• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.5
• /
• pp.63-73
• /
• 2022

Investigation on operation of the test apparatus for the M4 semi-freejet tests with a full-scale vehicle model was carried out utilizing domestic facilities. An integrated design of the experimental apparatus and the vehicle model was obtained through iterative computational fluid dynamics (CFD) analysis. The test results showed that the M4 nozzle of the apparatus was fully expanded to provide required test conditions. It was also found that the intake of the vehicle model successfully started, and the corresponding shadowgraph images were recorded during the test. A variable nozzle of the model was set to adjust the back pressure of the model combustor, and wall-static pressures were measured to obtain the pressure distribution at the main locations of the model. The flame of torch ignitors and pilot fuel ignition were observed in a flame-holder of the combustor.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.645-651
• /
• 2015

The objective of this study is to experimentally investigate the effect of design parameter on the mass ratio of a central-driven ejector. The design parameters are the primary nozzle area and distance ratios, diffuser exit-area ratio and mixing-tube length ratio. The experimental setup was an open-loop continuous circulation system which has a movable nozzle ejector, an electric motor-pump, a water tank, a control panel and high-speed camera unit. We calculated the mass ratio using the measured primary and suction-flow rates with the experimental parameter of primary water-flow rate or pressure. The results showed that the mass ratio increased with the primary nozzle distance ratio and mixing tube length ratio, while the mass ratio decreased with the primary nozzle-area ratio and diffuser exit-area ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.237-240
• /
• 2011

Numerical simulation was carried out to investigate the effect of pintle inflection point on the performance of the SNECMA modulatable thrust devices. Results show that the effect of inflection points in the pintle is to decrease aerodynamic load while maintaining required thrust level.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.167-173
• /
• 2003

For the measurement of mass flow rate at a wide range of operation conditions, it is required that the critical nozzle gas different diameters, since the mass flow rate through the critical nozzle depends on the nozzle supply conditions and the nozzle throat diameter. In the present study, both computational and experimental investigations are performed to explore the variable critical nozzle. Computational work using the 2-dimensional, axisymmetric, compressible Navier-Stokes equations are carried out to simulate the gas flow through variable critical nozzle. In experimnet, a cylinder with several different diameters is inserted into the critical nozzle to vary the nozzle throat diameter. Computational results are compared with the experimented ones. The computed results are in close agreement with experiment. It is found that the displacement and momentum thickness of variable critical nozzle are given as a function of Reynolds numbers. The discharge coefficient of the variable critical nozzle is predicted using an empirical equation.

• Journal of computational fluids engineering
• /
• v.1 no.1
• /
• pp.142-149
• /
• 1996

이차원 노즐을 통하여 저밀도 환경으로 팽창하는 희박류의 분석에 있어서 불연속좌표법과 결합된 유한차분법(finite-difference method coupled with the discrete-ordinate method, FDDO)과 직접모사법(direct-simulation Monte-Carlo method, DSMC)이 비교되었다. FDDO를 이용한 분석에서는 충돌적분모델을 도입하여 간단해진 볼츠만식(Boltzmann equation)이 불연속좌표법을 이용하여 물리적 공간에서는 연속이나 분자속도 공간에서는 불연속좌표로 표시되는 편미분방정식군으로 변환되어 유한차분법에의하여 수치해석 되었다. 직접모사법에서는 분자모델로 가변강구모델(variable hard sphere model, VHS)이, 충돌샘플링모델로는 비시계수법(no time counter method, NTC)이 채택되었다. 전혀 다른 두 가지 방법에 의한 노즐 내부에서의 유체흐름 해석결과는 매우 잘 일치하였으며, 노즐 외부의 plume 영역에서는 FDDO에 의한 해석결과가 직접모사법에 의한 해석결과에 비하여 약간 느린 팽창을 보였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.275-278
• /
• 2010

By changing the nozzle throat area during the operation, thrust of a pintle thruster can be adjusted easily such as a liquid propulsion. In this paper, numerical analysis was carried out for SNECMA's pintle thruster with different pintle shapes. Flow field and aerodynamic load changed drastically with pintle shapes. Bore in the pintle decreased aerodynamic load significantly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.392-396
• /
• 2012

Experimental and computational study for steady-state pintle driven nozzle throat flow are carried out by changing four pintle shape. Results show that thruster performance is influenced by pintle shape greatly. This attributes to the distorted throat area and chamber pressure change as the pintle shape and its penetration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.213-217
• /
• 2011

Unsteady numerical simulations of pintle nozzles were implemented for solid rocket thrust vector control. The variation of pintle location was considered using unsteady numerical techniques, and dynamic characteristics of various pintle models were investigated. In order to consider the variation of the pintle location, a moving mesh method was applied. The effects of shape and location of the pintle nozzle have been analytically investigated. And the results were compared with numerical results. The chamber pressure, mass flow and thrust are analyzed to take account dynamic characteristics of pintle performance.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.29-35
• /
• 2020

Transition Nozzles are used in industrial air-cooled heat exchangers and widely used in industrial sites as an important component in the heat energy transfer between a heat source and an actuating fluid. There is a worldwide demand for transition nozzles with various materials and shapes, depending on the use environment. This paper aims to improve the transition nozzle forging process suitable for the production of many varieties using Steps 1 to 6 of the TRIZ Methodology for Problem Solving. By utilizing the TRIZ Methodology, this study derives a method to design a variable mold, which is more efficient and can reduce costs compared with having to use several molds. To verify the suitability of the methods derived using the TRIZ technique, a forging analysis is performed on a transition nozzle using DEFORMⓇ, a commercial program for plasticity analysis, and the nozzle material is evaluated for damage as a result of deformation of the transition nozzle thickness. The derived methods can be applied to transition nozzle formation equipment to improve the efficiency of the formation process.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.484-489
• /
• 2003

The mass flow rate of gas flow through critical nozzle depends on the nozzle supply conditions and the cross-sectional area at the nozzle throat. In order that the critical nozzle can be operated at a wide range of supply conditions, the nozzle throat diameter should be controlled to change the flow passage area. This can be achieved by means of a variable critical nozzle. In the present study, both experimental and computational works are performed to develop variable critical nozzle. A cone-cylinder with a diameter of d is inserted into conventional critical nozzle. It can move both upstream and downstream, thereby changing the cross-sectional area of the nozzle throat. Computational work using the axisymmetric, compressible Navier-Stokes equations is carried out to simulate the variable critical nozzle flow. An experiment is performed to measure the mass flow rate through variable critical nozzle. The present computational results are in close agreement with measured ones. The boundary layer displacement and momentum thickness are given as a function of Reynolds number. An empirical equation is obtained to predict the discharge coefficient of variable critical nozzle.