• 한국재료학회지
• /
• 제28권12호
• /
• pp.709-713
• /
• 2018

To improve the etch rate of $Si_3N_4$ thin film, $H_2SiF_6$ is added to increase etching rate by more than two times. $SiO_3H_2$ is gradually added to obtain a selectivity of 170: 1 at 600 ppm. Moreover, when $SiO_3H_2$ is added, the etching rate of the $SiO_2$ thin film increases in proportion to the radius of the wafer. In $Si_3N_4$ thin film, there is no difference in the etching rate according to the position. However, in the $SiO_2$ thin film, the etching rate increases in proportion to the radius. At the center of the wafer, the re-growth phenomenon is confirmed at a specific concentration or above. The difference in etch rates of $SiO_2$ thin films and the reason for regrowth at these positions are interpreted as the result of the flow rate of the chemical solution replaced with fresh solution.

• 한국재료학회지
• /
• 제24권12호
• /
• pp.715-719
• /
• 2014

(PDDA/$SiO_2$) thin films that consisted of positively charged poly (diallyldimethylammonium chloride) (PDDA) and negatively charged $SiO_2$ nanoparticles were fabricated on a glass substrate by an applying voltage layer-by-layer (LBL) self-assembly method. In this study, the microstructure and optical properties of the (PDDA/$SiO_2$) thin films coated on glass substrate were measured as a function of the applied voltage on the Pt electrodes. When 1.0 V was applied to a Pt electrode in a PDDA and $SiO_2$ solution, the thickness of the $(PDDA/SiO_2)_{10}$ thin film increased from 79 nm to 166 nm. The surface roughness also increased from 15.21 nm to 33.25 nm because the adsorption volume of the oppositely charged PDDA and $SiO_2$ solution increased. Especially, when the voltage was applied to the Pt electrode in the $SiO_2$ solution, the thickness increase of the (PDDA/$SiO_2$) thin film was larger than that obtained when using the PDDA solution. The refractive index of the fabricated (PDDA/$SiO_2$) thin film was ca. n = 1.31~1.32. The transmittance of the glass substrate coated by (PDDA/$SiO_2$)6 thin film with a thickness of 106 nm increased from ca. 91.37 to 95.74% in the visible range.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제2권3호
• /
• pp.164-169
• /
• 2002

This paper mainly discusses the hard breakdown of 2.2-nm-thick $SiO_2$ films. It is shown that the hard breakdown event of a 2.2-nm-thick $SiO_2$ film greatly depends on the applied electric field. It is strongly suggested that the local weak spots created by applying a low initial stress to a 2.2-nm-thick $SiO_2$film resist the onset of hard breakdown. In other words, it is anticipated that the stored electrostatic energy is fast dissipated by trap-assisted tunneling in 2.2-nm-thick $SiO_2$ film. Consequently, it is strongly suggested that 2.2-nm-thick $SiO_2$ films are intrinsically quite robust.

• 센서학회지
• /
• 제9권2호
• /
• pp.90-95
• /
• 2000

$Si_3N_4/SiO_2/Si_3N_4$/Si 판위에 MgO 박막을 성장하여 MgO 단결정과 결정배향성이 유사한 초전형 적외선 센서용 기판을 제작하였다. RF 마그네트론 스퍼터링법으로 MgO 박막을 성장하였고, 그 위에 Pt 하부전극과 PLT 박막을 성장시킨 후 c축 배향성을 조사하였다. $500^{\circ}C$의 기판온도와 30 mTorr의 분위기 압력 및 160 W의 RF power에서 성장된 MgO 박막이 단결정 MgO가 가지는 배향성 정도의 우수한 a축 배향성을 보였고, 그 위에 성장된 PLT 박막은 MgO 단결정 기판위에 성장된 것과 거의 회절강도 변화가 유사한 c축 배향성을 보였다.

• 한국표면공학회지
• /
• 제53권2호
• /
• pp.59-66
• /
• 2020

Effects of Na₂SiO₃ concentration added into 0.1 M NaOH + 0.05 M NaF solution on the formation behavior and properties of PEO films on AZ91 Mg alloy were investigated under 1200 Hz of alternating current (AC) by voltage-time curves, in-situ observation of arc generation behavior and measurements of film thickness, surface roughness and micro vickers hardness. In the absence of Na₂SiO₃ in the 0.1 M NaOH + 0.05 M NaF solution, about 4 ㎛ thick PEO film was formed within 1 min and then PEO film did not grow but white spots were formed by local burning. Addition of Na₂SiO₃ up to 0.2 M caused more increased formation voltage and growth of PEO film with uniform generation of arcs. Addition of Na₂SiO₃ from 0.2 M to 0.4 M showed nearly the same voltage-time behavior and uniform arc generation. Addition of Na₂SiO₃ more than 0.5 M resulted in a decrease of formation voltage and non-uniform arc generation due to local burning. PEO film growth rate increased with increasing added Na₂SiO₃ concentration but maximum PEO film thickness was limited by local burning if added Na₂SiO₃ concentration is higher than 0.5 M. Surface roughness of PEO film increased with increasing added Na₂SiO₃ concentration and appeared to be proportional to the PEO film thickness. PEO film hardness increased with increasing added Na₂SiO₃ concentration and reached a steady-state value of about 930 H_V at more than 0.5 M of added Na₂SiO₃ concentration.

• E2M - 전기 전자와 첨단 소재
• /
• 제16권9호
• /
• pp.63.2-64
• /
• 2003

Epitaxial yttrium-stabilized HfO$_2$ thin films were deposited on p-type (100) Si substrates by pulsed laser deposition at a relatively lower substrate temperature of 550. Transmission electron microscopy observation revealed a fixed orientation relationship between the epitaxial film and Si; that is, (100)Si.(100)HfO$_2$ and [001]Si/[001]HfO$_2$. The film/Si interface is not atomically flat, suggesting possible interfacial reaction and diffusion, X-ray photoelectron spectrum analysis also revealed the interfacial reaction and diffusion evidenced by Hf silicate and Hf-Si bond formation at the interface. The epitaxial growth of the yttrium stabilized HfO$_2$ thin film on bare Si is via a direct growth mechanism without involoving the reaction between Hf atoms and SiO$_2$ layer. High-frequency capacitance-voltage measurement on an as-grown 40-A yttrium-stabilized HfO$_2$ epitaxial film yielded an dielectric constant of about 14 and equivalent oxide thickness to SiO$_2$ of 12 A. The leakage current density is 7.0${\times}$ 10e-2 A/$\textrm{cm}^2$ at 1V gate bias voltage.

• 한국전기전자재료학회논문지
• /
• 제22권11호
• /
• pp.969-973
• /
• 2009

In this study, the electrical and optical properties of $(SiO_2)_x(ZnO)_{100-x}$ (SZO) films prepared on the coming 7059 glass substrates by using rf-magnetron sputtering method are investigated. The deposition rate becomes maximum near 3 wt.% and gradually decreases when the $SiO_2$ content further increases. The growth rates of the SZO film with $SiO_2$ content of 3 wt.% is $4\;{\AA}/s$. We found that the average transmittance of all films is over 80% in the wavelength range above 500 nm. The optical band gap were decreased from 3.52 to 3.33 eV as an increase the deposition thickness. X-ray diffraction patterns showed that the film with a relatively low $SiO_2$ content (< 4 wt.%) is amorphous. SZO film with the $SiO_2$ contents of 2 wt.% showed the resistivity of about $3.8{\times}10^{-3}\;{\Omega}{\cdot}cm$. The sheet resistance decreases with increasing the heat treatment temperature.

• 전자공학회논문지A
• /
• 제32A권11호
• /
• pp.35-43
• /
• 1995

To obtain high quality of $Ta_{2}O_{5}$ film, two dielectric layers of $Si_{3}N_{4}$ and $Ta_{2}O_{5}$ were subsequently formed on Si wafer. Silicon nitride films were thermally grown in 10 Torr ammonia ambient by R.F induced heating system. The thickness of thermally grown $Si_{3}N_{4}$ film was able to be controlled in the range of tens $\AA$ due to the self-limited growth property. $Ta_{2}O_{5}$ film of 200$\AA$ thickness was then deposited on the as-grown $Si_{3}N_{4}$ film about 25$\AA$ thickness by sputtering method and annealed at $900^{\circ}C$in $O_{2}$ ambient for 1hr. Stoichiometry film was prepared by the annealing in oxygen ambient. Despite the high temperature anneal process, silicon oxide layer was not grown at the interface of the layered films because of the oxidation barrier effect of Si$_{3}$N$_{4}$ film. The fabricated $Ta_{2}O_{5}$/$Si_{3}N_{4}$ film showed low leakage current less than several nA and high dielectric breakdown strength.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.657-661
• /
• 2003

잉크젯 프린터 헤드용 기능성 막으로 많이 활용하고 있는 다층박막(SiO$_2$/poly-Si/SiN/SiO$_2$, 두께, 2.77 $\mu\textrm{m}$)과 다이아몬드 박막(두께, 1.6 $\mu\textrm{m}$)을 미소 외팔보($\mu$-CLB) 형태로 가공한 후 nanoindenter를 이용한 굽힘 시험 방법으로 탄성계수와 굽힘 강도를 측정하였으며 다층막을 이루는 박막 중 SiO$_2$ 박막(두께, 1 $\mu\textrm{m}$)과 SiN 박막(두께, 0.43 $\mu\textrm{m}$)의 탄성계수를 미소 외 팔보 굽힘 시험 방법과 nanoindentation 방법으로 측정한 후 그 결과를 비교하였다. 미소 외팔보 굽힘 시험방법으로 측정한 다층막의 탄성계수와 파괴강도는 외팔보의 폭이 18.5 $\mu\textrm{m}$에서 58.5 $\mu\textrm{m}$로 증가함에 따라 각각 68.08 ㎬과 2.495 ㎬에서 56.53 ㎬과 1.834 ㎬로 감소하였다. SiO$_2$ 박막의 탄성계수 측정값은 외팔보의 폭이 29.6$\mu\textrm{m}$ 와 59.5 $\mu\textrm{m}$ 범위에서 변하여도 영향을 받지 않고 68.16$\pm$0.942 ㎬이었으며, SiN 박막의 탄성계수는 215.45 ㎬이었다. Nanoindentation 방법으로 측정한 SiO$_2$ 박막과 SiN 박막의 탄성계수는 각각 98.78 ㎬, 219.38 ㎬이었다. 이 결과로부터 미소 외팔보 굽힘 시험방법으로 측정한 박막의 탄성계수가 nanoindentation 방법으로 측정한 탄성계수와 2% 미만의 차이를 보이며 일치함을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.612-616
• /
• 2000

This paper describes on the fabrication and characteristics of hot-film type micro-flowsensors integrated with Pt-RTD(resistance thermometer device) and micro-heater on the Si membrane in which MgO thin-film was used as medium layer in order to improve adhesion of Pt thin-film to SiO$_2$layer. The MgO layer improved adhesion of Pt thin-film to SiO$_2$layer without any chemical reactions to Pt thin-film under high annealing temperatures. Output voltages increased due to increase of heat-loss from sensor to external. The output voltage was 82 mV at $N_2$flow rate of 2000 sccm/min heating power of 1.2 W. The response time($\tau$:63%) was about 50 msec when input flow was stepinput