• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.3
• /
• pp.33-38
• /
• 2021

Recently, rollable and foldable displays are attracting great attention in the flexible display market due to their excellent form factor. To predict and prevent the mechanical failure of the display panels, it is essential to accurately understand the mechanical properties of brittle SiN_x thin films, which have been used as an insulating film in flexible displays. In this study, tensile properties of the ~130 nm- and ~320 nm-thick SiN_x thin films were successfully measured by coating a ~190 nm-thick organic nano-support-layer (PMMA, PS, P3HT) on the fragile SiN_x thin films and stretching the films as a bilayer state. Young's modulus values of the ~130 nm and ~320 nm SiN_x thin films fabricated through the controlled chamber pressure and deposition power (A: 1250 mTorr, 450 W/B: 1000 mTorr, 600 W/C: 750 mTorr, 700 W) were calculated as A: 76.6±3.5, B: 85.8±4.6, C: 117.4±6.5 GPa and A: 100.1±12.9, B: 117.9±9.7, C: 159.6 GPa, respectively. As a result, Young's modulus of ~320 nm SiN_x thin films fabricated through the same deposition condition increased compared to the ~130 nm SiN_x thin films. The tensile testing method using the organic nano-support-layer was effective in the precise measurement of the mechanical properties of the brittle thin films. The method developed in this study can contribute to the robust design of the rollable and foldable displays by enabling quantitative measurement of mechanical properties of fragile thin films for flexible displays.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.3
• /
• pp.133-140
• /
• 2002

The Ti-Si-N coating layers were synthesized on SKD 11 steel substrate by a DC reactive magnetron co-sputtering technique with separate Ti and Si targets. The high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS) analyses for the coating layers revealed that microstructure of Ti-Si-N layer was nanocomposite, consisting of nano-sized TiN crystallites surrounded by amorphous $Si_3$$N_4$ phase. The highest hardness value of about 39 GPa was obtained at the Si content of ~11at.%, where the microstructure had fine TiN crystallites (about 5nm in size) dispersed uniformly in amorphous matrix. As the Si content in Ti-Si-N films increased, the TiN crystallites became from aligned to randomly oriented microstructure, finer, and fully penetrated by amorphous phase. Free Si appeared in the layers due to the deficit of nitrogen source at higher Si content. Friction coefficient and wear rate of the Ti-Si-N coating layer significantly decreased with increase of relative humidity. The self-lubricating tribe-layers such as $SiO_2$ or (OH)$Si_2$ seemed to play an important role in the wear behavior of Ti-Si-N film against steel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.537-540
• /
• 2001

This paper presents the characteristics of Ta-N thin-film for high precision resistors, which were deposited on Si substrate by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(4~16 %)$N_2$). Structural properties studied using X-ray diffraction(XRD) indicate the presence of TaN, $Ta_3N_5$ or a mixture of Ta-N phases in the films depending on the amount of nitrogen in the sputtering gas. The chemical composition are investigated by auger electro spectroscopy(AES). The optimized conditions of Ta-N thin-film resistors were deposited in 4 % $N_2$ gas flow ratio. Under optimum conditions, the Ta-N thin-film resistors are obtained a high resistivity, $\rho=305.7{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-36 $ppm/^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.115-118
• /
• 2017

Highly photosensitive and wide bandgap amorphous silicon oxide (a-$SiO_x$:H) films were developed at low temperature ranges ($100{\sim}150^{\circ}C$) with employing plasma-enhanced chemical vapor deposition by optimizing $H_2/SiH_4$ gas ratio and $CO_2$ flow. Photosensitivity more than $10^5$ and wide bandgap (1.81~1.85 eV) properties were used for making the a-$SiO_x$:H thin film solar cells, which exhibited a high open circuit voltage of 0.987 V at the substrate temperature of $100^{\circ}C$. In addition, a power conversion efficiency of 6.87% for the cell could be improved up to 7.77% by employing a new n-type nc-$SiO_x$:H/ZnO:Al/Ag triple back-reflector that offers better short circuit currents in the thin film photovoltaic devices.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.619-625
• /
• 2008

The effects of thermal cycling on residual stresses in both inorganic passivation/insulating layer that is deposited by plasma enhanced chemical vapor deposition (PECVD) and organic thin film that is used as a bonding adhesive are evaluated by 4 point bending method and wafer curvature method. $SiO_2/SiN_x$ and BCB (Benzocyclobutene) are used as inorganic and organic layers, respectively. A model about the effect of thermal cycling on residual stress and bond strength (Strain energy release rate), $G_c$, at the interface between inorganic thin film and organic adhesive is developed. In thermal cycling experiments conducted between $25^{\circ}C$ and either $350^{\circ}C$ or $400^{\circ}C$, $G_c$ at the interface between BCB and PECVD $ SiN_x $ decreases after the first cycle. This trend in $G_c$ agreed well with the prediction based on our model that the increase in residual tensile stress within the $SiN_x$ layer after thermal cycling leads to the decrease in $G_c$. This result is compared with that obtained for the interface between BCB and PECVD $SiO_2$, where the relaxation in residual compressive stress within the $SiO_2$ induces an increase in $G_c$. These opposite trends in $G_cs$ of the structures including either PECVD $ SiN_x $ or PECVD $SiO_2$ are caused by reactions in the hydrogen-bonded chemical structure of the PECVD layers, followed by desorption of water.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.72-78
• /
• 1998

This paper is focused on the fabrication of reliable novel antifuse, which could operate at low voltage along with the improvement in OFF and ON-state properties. The fabricated antifuse consists of Al/BaTi$_{2}$O$_{3}$/SiO$_{2}$/TiW-silicide structure. Through the systematic analyses for bottom metal and the intermetallic insulator, material and electri cproperties were investiaged. TiW-silicide as the bottom electrode had smooth surface with average roughness of 11.angs. at 10X10.mu.m$^{2}$ and was bing kept as-deposited SiO$_{2}$ film stable. Amorphous BaTi$_{2}$O$_{3}$ film as the another insulator was chosen because of its low breakdown strength (2.5MV/cm). breakdown voltage of antifuse is remarkably reduced by using BaTi$_{2}$O$_{3}$ film, and leakage current of that maintained low level due to the SiO$_{2}$ film. Low ON-resistance (46.ohm./.mu.m$^{2}$) and low programming voltage(9.1V) can be obtained in theses antifuses with 220.angs. double insulator layer and 19.6X10$^{-6}$ cm$^{2}$ area, while keeping sufficient OFF-state reliability (less than 1nA).

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.1
• /
• pp.22-25
• /
• 2000

Polycrystalline SBTN layered ferroelectric thin film with various Nb mole ratios were prepared by sol-gel method Pt/ $SiO_2$/Si (100) substrates. The films were annealed at different temperature and characterized in terms of phase and microstructure. The films were crystallized with a high (105) diffraction intensity and had rodike structure, SBTN films fired at 800$^{circ}C$ revealed standard hysteresis loops with no fatigue for up to 10$^{10}$ cycles. At an applied voltage of 5V the dielectric constant($varepsilon$) , dissipation factor (tan $delta$), remanent polarization(ZPr) and coercive field(Ec) of typical S $r_{0.8}$B $i_{2.3}$(T $a_{1-x}$ N $b_{x}$) $O_{9+}$$alpha$/ thin film(x=0.1) prepared on Pt/ $SiO_2$/Si (100) were about 277.7, 0.042, 3.74$mu$C/$textrm{cm}^2$, and 24.8kv/cm respectively.ly.y. respectively.ly.y.y..

• Journal of the Semiconductor & Display Technology
• /
• v.4 no.1 s.10
• /
• pp.55-59
• /
• 2005

The ($Sr_{1-x}Ca_{x})Ti_{3}$(SCT) thin film are deposited on Pt-coated electrode (Pt/TiN/$SiO_{2}$/Si) using RF sputtering method. The maximum dielectric constant of SCT thin film is obtained by annealing at 600[$^{\circ}C$]. The temperature properties of the dielectric loss have a value within 0.02 in temperature lunges of -80 $\∼$ +90[$^{\circ}C$]). The capacitance characteristics had a stable value within ${\pm}4\%$. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films is observed above 200[kHz).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.94-98
• /
• 2000

Polycrystalline SBTN ferroelectric thin films were prepared by sol-gel method with various Nb mole ratios on Pt/ $SiO_2$/Si (100) substrates. The films were annealed at different temperatures and characterized in terms of phase and microstructure. Relatively a well saturated hysteresis pattern was obtained at x =0.2 in S $r_{0.8}$B $i_{2.3}$(T $a_{1-x}$ N $b_{x}$)$_2$ $O_{9+}$$\alpha$/ thin films. At an applied voltage of 5V, the dielectric constant ($\varepsilon$$_{r}$) and dissipation factor (tan $\delta$) of typical S $r_{0.8}$B $i_{2.3}$(T $a_{1-x}$ N $b_{x}$)$_2$ $O_{9+}$$\alpha$/ thin film (x=0.2) were about 236.2 and 0.034. Measured remanent polarization (2Pr) and coercive field (Ec) were 4.28C/c $m_2$, and 38.88kv/cm respectively. No fatigue was observed up to 6$\times$10$_{10}$ switching cycles at 5V and the normalized polarization reduced by a factor of only 4%.%. 4%.%. 4%.%.%.%.%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.468-470
• /
• 1999

One of the most critical problem in etching of platinum was generally known that the etch slope was gradual. therefore, the addition of $N_2$ gas into the Ar/C1$_2$ gas mixture, which has been proposed the optimized etching gas combination for etching of platinum in our previous article, was performed. The selectivity of platinum film to oxide film as an etch mask increased with the addition of N2 gas, and the steeper etch slope over 75 $^{\circ}$ could be obtained. These phenomena were interpreted the results the results of a blocking layer such as Si-N or Si-O-N on the oxide mask. Compostional analysis was carried out by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). Moreover, it could be obtained the higher etch rate of Pt film and steeper profile without residues such as p.-Cl and Pt-Pt ant the addition N\ulcorner of 20 % gas in Ar(90)/Cl$_2$(10) Plasma. The Plasma characteristic was extracted from optical emissionspectroscopy (OES).