• Journal of the Semiconductor & Display Technology
• /
• v.21 no.1
• /
• pp.119-126
• /
• 2022

MAS-based glass, which has been studied to replace the ceramic material used in the plasma etching chamber, has problems such as forming and processing due to its high melting temperature. To solve this problem, in this study, fluoride was added to the existing MAS-based glass to increase the workability in the glass manufacturing and to improve the chemical resistance to CF₄/Ar/O₂ plasma gas. Through RAMAN analysis, the structural change of the glass according to the addition of fluoride was observed. In addition, it was confirmed that high-temperature viscosity and thermal properties decreased as the fluoride content increased and plasma resistance was maintained, it showed an excellent etching rate of up to 11 times compared to quartz glass.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3367-3371
• /
• 2013

MgO nanorods were fabricated by the thermal evaporation of $Mg_3N_2$. The influence of ZnO sheathing and hydrogen plasma exposure on the photoluminescence (PL) of the MgO nanorods was studied. PL measurements of the ZnO-sheathed MgO nanorods showed two main emission bands: the near band edge emission band centered at ~380 nm and the deep level emission band centered at ~590 nm both of which are characteristic of ZnO. The near band edge emission from the ZnO-sheathed MgO nanorods was enhanced with increasing the ZnO shell layer thickness. The near band edge emission from the ZnO-sheathed MgO nanorods appeared to be enhanced further by hydrogen plasma irradiation. The underlying mechanisms for the enhancement of the NBE emission from the MgO nanorods by ZnO sheathing and hydrogen plasma exposure are discussed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.93-99
• /
• 1997

High Temperature wear behavior of plasma sprayed ZrO$_2$ and MoS$_2$, $Fe_2O_3$ coatings were investigated for high temperature wear resistance applications. The MoS$_2$, $Fe_2O_3$ added powders containing 2.5, 5.0, 7.5, 10.0 mol% of $MoS_2$, $Fe_2O_3$ for plasma spray were made by spray drying method. Wear test were performed at temperature ranges from room temperature to 600$\circ$C. The microstructural change of coatings and the worn. surface were examined by SEM and XRD. In ZrO$_2$ coating, the coefficient of friction and wear amount of room temperature to 400$\circ$C was increased with temperature and decreased with temperature over 400$\circ$C. The coefficient of friction and wear amount of MoS$_2$ added coatings were increased with temperature, but those of $Fe_2O_3$ added coatings had lower coefficient of friction and higher wear resistance than ZrO$_2$ coating.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.491-491
• /
• 2013

A novel plasma system has been developed for 3-dimensional modification of the carbon nano-powders. Improvement of dispersion of these nano materials are studied by plasma discharge, not using chemical modification. The plasma process is considered to great advantages over wet chemical process due to environmental, economic viewpoint, and uniformity over the treated volume. The uniform dispersion is a critical factor for these material's nano composite applications. Using this plasma system, graphene, carbon black, and CNT was treated and functionalized. Several key discharge conditions such as Ar/H2/O2 or Ar/H2/NH3 gas ratio, treatment time, power, feeder's vibration frequency are investigated. Hydrophobic of graphene has turned some more into hydrophilic by reaction test with water, electrophoresis, surface contact angle test, and turbidity analysis. The oxygen content ratio in the plasma treated CNT has increased about 3.7 times than the untreatedone. In the case of graphene and carbon black, the oxygen- and nitrogen- content has been enhanced average 10%. O-H (N-H) peak, C-O (C-N) peak, and C=O (C=N) peak data have been detected by FTIR measurement and intensified compared to before-plasma treatment due to O2 or NH3 content.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.15-19
• /
• 2007

This paper reports the effects of Ar ion beam surface treatment on a $SiO_2$ dielectric layer in organic thin film transistors. We compared the electrical properties of pentacene-based OTFTs, treated by $O_2$ plasma or Ar ion beam treatments and characterized the states of the surface of the dielectric by using atomic force microscopy and X-ray photoelectron spectroscopy. For the sample which received $O_2$ plasma treatment, the mobility increased significantly but the on/off current ratio was found very low. The Ar ion beam-treated sample showed a very high on/off current ratio as well as a moderately improved mobility. XPS data taken from the dielectric surfaces after each of treatments exhibit that the ratio of between Si-O bonds and O-Si-O bonds was much higher in the $O_2$ plasma treated surface than in the Ar ion beam treated surface. We believe that our surface treatment using an inert gas, Ar, carried out an effective surface cleaning while keeping surface damage very low, and also the improved device performances was achieved as a consequence of improved surface condition.

• Journal of the Korean Ceramic Society
• /
• v.48 no.2
• /
• pp.160-167
• /
• 2011

Plasma sprayed ceramic coatings inherently contain pores and usually also cracks. Post-treatment of the plasma sprayed coatings is a way to close the connected pores and cracks. In this study, post-sealing treatment in plasma sprayed $Al_2O_3$ coatings was employed to overcome the reduction of coating properties. $Al_2O_3$ plasma thermal spray coating was made on aluminum alloys plate, $CrO_3$ post coating and heat treatment at $550^{\circ}C$ was carried out in order for final $Cr_2O_3$ to be saturated through phase transformation. Chromia sealing began at the fine defect in coated microstructure, while larger pores were permeated later. The increase in concentration and treatment frequency of sealing solution resulted in the decrease of porosity of coating layer, while cracks occurred partially after the third treatment. After twice treatment of 10M $CrO_3$ solution, microhardness and breakdown voltage of $Al_2O_3$ coatings were found to increase by ${\fallingdotseq}$ 50% and ${\fallingdotseq}$ 390% respectively than without post-treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.254-254
• /
• 2016

Tin dioxide (SnO2) thin film is one of the most important n-type semiconducting materials having a high transparency and chemical stability. Due to their favorable properties, it has been widely used as a base materials in the transparent conducting substrates, gas sensors, and other various electronic applications. Up to now, SnO2 thin film has been extensively studied by a various deposition techniques such as RF magnetron sputtering, sol-gel process, a solution process, pulsed laser deposition (PLD), chemical vapor deposition (CVD), and atomic layer deposition (ALD) [1-6]. Among them, ALD or plasma-enhanced ALD (PEALD) has recently been focused in diverse applications due to its inherent capability for nanotechnologies. SnO2 thin films can be prepared by ALD or PEALD using halide precursors or using various metal-organic (MO) precursors. In the literature, there are many reports on the ALD and PEALD processes for depositing SnO2 thin films using MO precursors [7-8]. However, only ALD-SnO2 processes has been reported for halide precursors and PEALD-SnO2 process has not been reported yet. Herein, therefore, we report the first PEALD process of SnO2 thin films using SnCl4 and oxygen plasma. In this work, the growth kinetics of PEALD-SnO2 as well as their physical and chemical properties were systemically investigated. Moreover, some promising applications of this process will be shown at the end of presentation.

• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.37-43
• /
• 2009

Silicon dioxide as gate dielectrics was grown at $400^{\circ}C$ on a polycrystalline Si substrate by inductively coupled plasma oxidation using a mixture of $O_2$ and $N_2O$ to improve the performance of polycrystalline Si thin film transistors. In conventional high-temperature $N_2O$ annealing, nitrogen can be supplied to the $Si/SiO_2$ interface because a NO molecule can diffuse through the oxide. However, it was found that nitrogen cannot be supplied to the Si/$SiO_2$ interface by plasma oxidation as the $N_2O$ molecule is broken in the plasma and because a dense Si-N bond is formed at the $SiO_2$ surface, preventing further diffusion of nitrogen into the oxide. Nitrogen was added to the $Si/SiO_2$ interface by the plasma oxidation of mixtures of $O_2/N_2O$ gas, leading to an enhancement of the field effect mobility of polycrystalline Si TFTs due to the reduction in the number of trap densities at the interface and at the Si grain boundaries due to nitrogen passivation.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.1
• /
• pp.64-71
• /
• 2023

In this study, we investigated the effects of BiAlSiO glass composition on its glass forming range, thermal properties, and plasma resistance. The results showed that increasing the Al2O3 content suppressed the tendency for crystallization and hindered glass formation beyond a certain threshold. Bi2O3 was found to increase the content of non-bridging oxygen, resulting in a decrease in glass transition temperature and an increase in thermal expansion coefficient. Furthermore, the etching rate was found to improve with increasing Al2O3 content but decrease with increasing SiO2 content. It was concluded that the boiling point of fluorinated compounds should be considered to 900℃. Therefore, this study is expected to contribute to the understanding of the properties of BiAlSiO glass and its application to low temperature melting PRG compositions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.752-758
• /
• 2010

The etching characteristics of indium tin oxide (ITO) thin films in an $O_2/BCl_3/Ar$ plasma were investigated. The etch rate of ITO thin films increased with increasing $O_2$ content from 0 to 2 sccm in $BCl_3$/Ar plasma, whereas that of ITO decreased with increasing $O_2$ content from 2 sccm to 6 sccm in $BCl_3$/Ar plasma. The maximum etch rate of 65.9 nm/m in for the ITO thin films was obtained at 2 sccm $O_2$ addition. The etch conditions were the RF power of 500 W, the bias power of 200 W, the process pressure of 15 mTorr, and the substrate temperature of $40^{\circ}C$. The analysis of x-ray photo electron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of ITO thin films and etch species.