• Journal of Environmental Science International
• /
• v.29 no.11
• /
• pp.1025-1032
• /
• 2020

This work was performed to develop a dip injection wet scrubber (DIWS) system with chlorine dioxide as the oxidant. The exhaust pollutants from a lime kiln of paper-mill were introduced to the system. When NaClO₃ was used to oxidize NO into NO₂, the oxidation was unsatisfactory and the combination of HNO₃ or H₂SO₄ was required for 100% oxidation. ClO₂ is recommended to oxidize NO and SO₂ effectively. With the combination of 1^st stage of DIWS and ClO₂, 57.1% of NOx and 98% of SO₂ were effectively removed. In the case of 2^nd stage of DIWS and ClO₂, 93.5% of NOx and 99% of SO₂ were removed. The ClO₂+DIWS process was superior to the ClO₂+Scrubber process in terms of investment, running cost and NOx removal efficiency.

• Korean Journal of Materials Research
• /
• v.27 no.2
• /
• pp.113-118
• /
• 2017

Natural and expandable graphites were chemically treated in acidic aqueous solutions such as acetic acid or mixtures of acetic acid and nitric acid. Structures and thermal conductivities of the as-treated graphites were characterized in detail. Both graphites were significantly oxidized in the mixed acidic solution of $H_2SO_4$ and $HNO_3$, which condition was generally used for the oxidation of carbon nanotubes. This considerable oxidation of graphites caused a depression of their thermal conductivity. The structural characteristics, obtained by XRD and XPS, show that the graphites treated in the relatively weak acidic conditions (acetic acid or mixture of acetic acid and nitric acid) were quite similar to the untreated graphites. However, the thermal conductivities of both acidic-treated graphites were remarkably increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.248-249
• /
• 2014

Photocatalytic cement is receiving attention due to its high oxidation power that oxidizes nitrogen oxides (NOx), thus contributing to clean atmospheric environment. However, there has not been a thorough investigation on durability of a parent material, cementitious material, as a result of photocatalytic reactions. In this study, durability of photocatalytic cementitious materials exposed to nitrogen dioxide (NO₂) gas was examined. Titanium dioxide (TiO₂) nanoparticles containing cement paste samples were exposed to cycles of NO₂ with UV light, followed by wetting and drying to simulate environmental condition. The surface of samples was characterized mechanically, chemically, and visually during the cycling. The results indicate that the photocatalytic efficiency decreased with continued NO₂ oxidation due to calcium carbonate formation. The pits found from SEM demonstrate that chemical deterioration have occurred, such as acid attack or leaching. In conclusion, the photocatalytic reactions and its product could alter cementitious materials chemically and mechanically which could further affect long-term durability.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.12
• /
• pp.647-655
• /
• 2016

Lead dioxide ($PbO_2$) is an electrode material that is effective for organic pollutant degradation based on hydroxyl radical ($^{\bullet}OH$) attack. Representative parameters for $PbO_2$ electrodeposition are summarized to current, temperature, reaction time, concentration of Pb(II) and electrolyte agent. In this study, $Ti/PbO_2$ electrodes were fabricated by electrodeposition method under controlled reaction time, current density, temperature, concentration of $HNO_3$ electrolyte. Effects of deposition parameters on $^{\bullet}OH$ evolution were investigated in terms of electrochemical bleaching of p-Nitrosodimethylaniline (RNO). As major results, the $^{\bullet}OH$ evolution was promoted at the $PbO_2$ that was deposited in longer reaction time (1-90 min), lower current density ($0.5-50mA/cm^2$), higher temperature ($5-65^{\circ}C$) and lower $HNO_3$ concentration (0.01-1.0 M). Especially, the $PbO_2$ which was deposited in 0.01 M of lowest $HNO_3$ concentration by applying $20mA/cm^2$ for above 10 min was most effective on $^{\bullet}OH$ evolution. The performance gap between $PbO_2$s that was best and worst in $^{\bullet}OH$ evolution was about 41%. Among the properties of $PbO_2$ related on $^{\bullet}OH$ evolution performance, conductivity of $Ti/PbO_2$ significantly influenced on $^{\bullet}OH$ evolution. The increase in conductivity promoted $^{\bullet}OH$ evolution. In addition, the increase in crystal size of $PbO_2$ interfered $^{\bullet}OH$ evolution at surface of some $PbO_2$ deposits.

• Analytical Science and Technology
• /
• v.22 no.2
• /
• pp.186-190
• /
• 2009

The oxidation studies of a sulfur to a sulfate ion by various oxyhalide oxidants in organic (thiourea, methionine) and inorganic (sulfate, thiophosphate) compounds were carried out in an acidic solution. The optimized result of the oxidation reaction was obtained when a bromate compound (${BrO_3}^-$) as an oxidant and a 3 M $HNO_3$ solvent were used. The chemical yield for the oxidation of the organic and inorganic sulfur compounds to a sulfate ion was monitored as 80% for thiophosphate, 87% for methionine, and 100% for thiourea and sulfate within 5% RSD. The oxidations of thiourea required at least 1.6 equivalents of the bromate in an acidic solution. In the case of the oxidation of methionine and thiophosphate, the oxidation yields were above 80% if the bromate was used at 20 times higher than that of the substrates. The sulfate ion was quantitatively measured by using a GPC counting of $^{35}S$ followed by precipitates of $BaSO_4$. A quenching correction curve for the $^{35}S$ counting was obtained to use the difference via the precipitate weight result.

• Journal of the Korean Chemical Society
• /
• v.45 no.4
• /
• pp.298-303
• /
• 2001

The trace-level mercury in bio-materials has been determinated by the anodic stripping square wave voltammetry (ASSWV)-technique at glassy carbon electrode. Prior to the analysis, the bio-materials were digested with $HNO_3/H_2SO_4$ mixture and KMnO4 was added to complete an oxidation process of the mixture. The detection limit of the mercury varied greatly with deposition time, deposition potential, pH and stirring rate. When the deposition was carried out for 240 sec on 400 rpm stirring at -1.0 volts vs. Ag/AgCl, the detection limit was below 0.5 ppb ($2.5{\times}10^{-9}M$). The accumulated mercury was high in the kidney and liver, and low in the brain according to the determination of mercury accumulation for a white rat by this method.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.61-65
• /
• 2013

In this work, the anodic oxidation of carbon fibers was carried out to enhance the mechanical interfacial properties of carbon fibers-reinforced epoxy matrix composites. The surface characteristics of the carbon fibers were studied by FTIR, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Also, the mechanical interfacial properties of the composites were studied with interlaminar shear strength (ILSS), critical stress intensity factor ($K_{IC}$), and critical strain energy release rate ($G_{IC}$). The anodic oxidation led to a significant change in the surface characteristics of the carbon fibers. The anodic oxidation of carbon fiber improved the mechanical interfacial properties, such as ILSS, $K_{IC}$, and $G_{IC}$ of the composites. The mechanical interfacial properties of the composites anodized at 20% sulfuric/nitric (3/1) were the highest values among the anodized carbon fibers. These results were attributed to the increase of the degree of adhesion at interfaces between the carbon fibers and the matrix resins in the composite systems.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.149-153
• /
• 2001

This paper describes on the fabrication of Fe-Co hydrophilic magnetic fluids from the waste pickling liquor of steel. By adding with HNO$_3$in the waste liquor oxidation is proceeded from Fe$^{3+}$ion at 6$0^{\circ}C$ with air blowing. Ultra-fine Co-ferrite particles with the mean particle size of 50 $\AA$ were produced at pH 12 after adjusting the ratio of Fe$^{3+}$Co$^{2+}$=7/3(wt%) and Fe-Co particles with the mean particle size of 94 $\AA$ were produced by reducing the Co-ferrite particle with H$_2$at the temperature of 50$0^{\circ}C$. After triple adsorption of oleic acid dodecyl benzene sulfonate(D.B.S.) and tetra methyl ammonium(T.M.A.) ions on the surface of Fe-Co particles Fe-Co hydrophilic magnetic fluid was produced by dispersing the Fe-Co particles in ethylene glycol solution. The magnetization of the Fe-Co hydrophilic magnetic fluid increased with increasing the Fe-Co concentration. The magnetic fluid containing 70% (g/cc) Fe-Co showed 73 emu/g in magnetization at the magnetic intensity of 10 kOe.kOe.e.

• Analytical Science and Technology
• /
• v.5 no.1
• /
• pp.143-152
• /
• 1992

Corrosion resistances in various acids and high temperature oxidation properties have been investigated for the Ni-base superalloy KM 1557. Corrosion tests were performed in $H_2SO_4$, HCl, $HNO_3$, $H_3PO_4$ and $CH_3COOH$. Oxidation tests were carried out in air for 20 and 110hrs at $900^{\circ}C$, $950^{\circ}C$ and $1050^{\circ}C$. Hot corrosion tests were done in salt bath of 75% $Na_2SO_4-25%$ NaCl at $900^{\circ}C$ for 20hrs. After the tests, the samples were observed by optical microscopy and analysed by EPMA and X-ray mapping in order to investigate the distribution of composition. It was shown that corrosion resistances in various acids and hot salt bath were proven to be excellent. It was suggested that the amounts of oxides were determined mainly by the depth of internal and intergranular $Al_2O_3$ oxide layers.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.4
• /
• pp.346-351
• /
• 2020

The removal characteristics of copper (Cu) from electrochemical surface by voltage-activated reaction were reviewed to assess the applicability of electrochemical-mechanical polishing (ECMP) process in three types of electrolytes, such as HNO₃, KNO₃ and NaNO₃. Electrochemical surface conditions such as active, passive, transient and trans-passive states were monitored from its current-voltage (I-V) characteristic curves obtained by linear sweep voltammetry (LSV) method. In addition, the oxidation and reduction process of the Cu surface by repetitive input of positive and negative voltages were evaluated from the I-V curve obtained using the cyclic voltammetry (CV) method. Finally, the X-ray diffraction (XRD) patterns and energy dispersive spectroscopy (EDS) analyses were used to observe the structural surface states of a Cu electrode. The electrochemical analyses proposed in this study will help to accurately control the material removal rate (MRR) from the actual ECMP process because they are a good methodology for predicting optimal electrochemical process parameters such as current density, operating voltage, and operating time before performing the ECMP process.