• Korean Journal of Materials Research
• /
• v.20 no.9
• /
• pp.451-456
• /
• 2010

A promising candidate material for a $H_2$ permeable membrane is SiC due to its many unique properties. A hydrogen-selective SiC membrane was successfully fabricated on the outer surface of an intermediate multilayer $\gamma-Al_2O_3$ with a graded structure. The $\gamma-Al_2O_3$ multilayer was formed on top of a macroporous $\alpha-Al_2O_3$ support by consecutively dipping into a set of successive solutions containing boehmite sols of different particle sizes and then calcining. The boehmite sols were prepared from an aluminum isopropoxide precursor and heated to $80^{\circ}C$ with high speed stirring for 24 hrs to hydrolyze the precursor. Then the solutions were refluxed at $92^{\circ}C$ for 20 hrs to form a boehmite precipitate. The particle size of the boehmite sols was controlled according to various experimental parameters, such as acid types and acid concentrations. The topmost SiC layer was formed on top of the intermediate $\gamma-Al_2O_3$ by pyrolysis of a SiC precursor, polycarbosilane, in an Ar atmosphere. The resulting amorphous SiC-on-$Al_2O_3$ composite membrane pyrolyzed at $900^{\circ}C$ possessed a high $H_2$ permeability of $3.61\times10^{-7}$ $mol{\cdot}m^{-2}{\cdot}s^{-1}{\cdot}Pa^{-1}$ and the $H_2/CO_2$ selectivity was much higher than the theoretical value of 4.69 in all permeation temperature ranges. Gas permeabilities through a SiC membrane are affected by Knudsen diffusion and a surface diffusion mechanism, which are based on the molecular weight of gas species and movement of adsorbed gas molecules on the surface of the pores.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.939-943
• /
• 2011

In this paper, reliability of the two sandwiched MIM capacitors of $Al_2O_3-HfO_2-Al_2O_3$ (AHA) and $SiO_2-HfO_2-SiO_2$ (SHS) with hafnium-based dielectrics was analyzed using two kinds of voltage stress; DC and AC voltage stresses. Two MIM capacitors have high capacitance density (8.1 fF/${\mu}m^2$ and 5.2 fF/${\mu}m^2$) over the entire frequency range and low leakage current density of ~1 nA/$cm^2$ at room temperature and 1 V. The charge trapping in the dielectric shows that the relative variation of capacitance (${\Delta}C/C_0$) increases and the variation of voltage linearity (${\alpha}$/${\alpha}_0$) gradually decreases with stress-time under two types of voltage stress. It is also shown that DC voltage stress induced greater variation of capacitance density and voltage linearity than AC voltage stress.

• Journal of the Korean Ceramic Society
• /
• v.54 no.5
• /
• pp.400-405
• /
• 2017

$P_2O_5-ZnO-SiO_2-R_2O$ glasses were synthesized as a sealing material for large scale dye-sensitized solar cells (DSSC). Compositional effects of $P_2O_5$ and ZnO were examined by varying their contents. Their viscosity and glass stability at sintering temperatures of less than $550^{\circ}C$ were examined by flow button test. Glass transition temperature and structural change upon compositional change were investigated. Chemical stability against electrolyte was also examined by immersing the glasses in the electrolyte for 72 h at $85^{\circ}C$.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.20-28
• /
• 2016

This study has developed an organic/inorganic hybrid solution by addition of $SiO_2$ polysilicate and Melamine to the urethane. The three types of cold rolled steel were evaluated a corrosion resistance properties by using these solutions. The urethane solution(U) and the urethane solution with $SiO_2$ polysilicate($US_7$) were generate a lot of corrosion. The urethane solution with $SiO_2$ polysilicate and melamine($US_7M_3$) was excellent in corrosion resistance, regardless of the steel type. In addition, corrosion resistance has been shown to depend on the tensile strength. The appearance of coating by U and $US_7$ solution is bumpy surface, and were a lot of fine defects. $US_7M_3$ solution is made a sophisticated molecular cross-linking structure inside the coating, it was a slick surface. Other characteristics are exhibited the excellent property for all solutions.

• Journal of Magnetics
• /
• v.19 no.2
• /
• pp.121-125
• /
• 2014

$CoFe_2O_4(CFO)/BaTiO_3(BTO)/CoFe_2O_4(CFO)$ multilayered thin films were deposited on $Pt/TiO_2/SiO_2/Si$ substrates by the pulsed laser deposition (PLD) system with KrF excimer laser (${\lambda}=248nm$). BTO, CFO, BTO/CFO and CFO/BTO/CFO structured thin films were prepared and their crystal structures and microstructures, as well as their magnetic and magneto-electrical properties, were studied. The C-V characteristics of these multilayered thin films with different capacitor structures were obtained to confirm the change in their capacitances under a magnetic field. Finally, the capacitance of the CFO/BTO/CFO thin film as a function of bias voltage under an in-plane magnetic field of 1,000 Oe increased to 951.04 pF at 1 MHz, from 831.90 pF measured under no magnetic field, indicating 14.3% increase in magnetocapacitance.

• Resources Recycling
• /
• v.29 no.6
• /
• pp.73-78
• /
• 2020

To use a tailing obtained from coal beneficiation as a raw material for glass material, the behaviors of phase transformation of the tailing was investigated according to sintered temperature with the addition of Na2CO3. As a result of the experiment, mullite was formed at 700~1,100 ℃, and the mullite and the cristobalite just only existed at 1,450 ℃. The glassification ratio of the coal tailing was to be 97.9 wt.% at 1,450 ℃ with the addition of Na2CO3 to tailing weight ratios of 10 wt.%. However, in the case of sample of coal tailing with 20 wt.% Na2CO3 added, nepheline(Na2O·Al2O3·2SiO2) was produced during the re-sintering(2nd sintering) at 1,100 ℃. From the results, the suitable addition amount of Na2CO3 for glassification of coal tailing was found around 10 wt.%.

• Journal of the Korean Ceramic Society
• /
• v.43 no.3 s.286
• /
• pp.169-172
• /
• 2006

We have synthesized a $Eu^{2+}-activated\;{(Sr,Ba)}_2SiO_4$ yellow phosphor and investigated the development of blue LEDs by combining the phosphor with a InGaN blue LED chip (${\lambda}_{em}$=405 nm). The InGaN-based ${(Sr,Ba)}_2SiO_{4}:Eu$ LED lamp shows two bands at 405 nm and 550 nm. The 405 nm emission band is due to a radiative recombination from a InGaN active layer. This 405 nm emission was used as an optical transition of the ${(Sr,Ba)}_2SiO_{4}:Eu$ phosphor. The 550 nm emission band is ascribed to a radiative recombination of $Eu^{2+}$ impurity ions in the ${(Sr,Ba)}_2SiO_4$ host matrix. In the preparation of UV Yellow LED Lamp with ${(Sr,Ba)}_2SiO_{4}:Eu$ yellow phosphor, the highest luminescence efficiency was obtained at the epoxy-to-yellow phosphor ratio of 1:0.45. At this ratio, the CIE chromaticity was x=0.4097 and y=0.5488.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.196-201
• /
• 2001

The dependence of CoFe interfacial layer thickness and plasma oxidation condition on tunneling magnetoresistance (TMR) in Ta/NiFe/FeMn/NiFe/Al$_2$O$_3$/NiFe/Ta tunnel junctions was investigated. As the CoFe layer thickness increases, TMR ratio rapidly increases to 13.7 % and decreases with further increase of the CoFe layer thickness. The increase of TMR with the CoFe thickness up to 25 was thought to be due mails to the high spin-polarization of CoFe. The maximum MR of 15.3% was obtained in the Si(100)/Ta(50 )/NiFe(60 )/FeMn(250 )/NiFe(70 )/Al$_2$O$_3$/NiFe(150 )/Ta(50 ) magnetic tunnel junction with a 16 Al oxidized for 40 sec using a Ar/O$_2$ (1:4) mixture gas.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.293-297
• /
• 2003

Silicon dioxide (SiO$_2$) layers were fabricated on Si$_3$N$_4$/SiO$_2$/Si layer structures by low pressure chemical vapor deposition (LPCVD). Potassium and aluminum were then coimplanted by implanting potassium ions with the energy of 100 ［keY］ and dose of 5x10$^{16}$ [cm￣$^2$］ and 1x10$^{17}$ [cm￣$^2$］ into an aluminum buffer layer on the SiO$_2$Si$_3$N4/SiO$_2$/Si structure. The pH, pNa, and pK ion sensitivities of the resulting layers were investigated and compared to those of as-deposited silicon dioxide layer. The pK-sensitivity of the silicon dioxide was enhanced by the K and Al coimplantation. On the contrary, the pH and pNa-sensitivities of the coimplanted silicon dioxides were quite lower than that of the as-deposited silicon dioxide.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2288-2292
• /
• 2007

The catalytic activities of nickel-based catalysts were estimated for oxidizing acetaldehyde of VOCs exhausted from industrial facilities. The catalysts were prepared by sol-gel methods of SiO2 and SiO2-TiO2 as a xerogel followed by impregnating Al2O3 powder with the nickel nitrate precursor. The crystalline structure and catalytic properties for the catalysts were investigated by use of BET surface area, X-ray diffraction (XRD), Xray photoelectron spectroscopy (XPS) and temperature programmed reduction (TPR) techniques. These results show that nickel oxide is transformed to NiAl2O4 spinel structure at the calcination temperature of 400 °C in response to the steps with after- and co-impregnation of Al2O3 powder in sol-gel process. The NiAl2O4 could suppress the oxidation reaction of acetaldehyde by catalysts. The NiO is better dispersed on SiO2-TiO2/Al2O3 support than SiO2/Al2O3 and SiO2-TiO2-Al2O3 supports. From the testing results of catalytic activities for oxidation of acetaldehyde, Catalysts showed a big difference in conversion efficiencies with the way of the preparation of catalysts and the loading weight of nickel. The catalyst of 8 wt.% Ni/TiO2-SiO2/Al2O3 showed the best conversion efficiency on acetaldehyde oxidation with 100% conversion efficiency at 350 °C.