• Clean Technology
• /
• v.25 no.3
• /
• pp.245-255
• /
• 2019

Pressurized oxy-fuel combustion is a promising technology for $CO_2$ capture with a benefit of improving power plant efficiency compared with atmospheric oxy-fuel combustion. Prior to $CO_2$ compression in this process, a flue gas condenser (FGC) is used to remove $H_2O$ while recovering the latent heat. At the same time, the FGC has a potential for high-efficiency removal of $SO_x$ and $NO_x$ by exploiting their good solubility in water. In this study, experiments were carried out in a lab-scale, direct contact FGC under different pressures varying between 1 and 20 bar to evaluate the removal efficiency of $SO_2$ and $NO_x$ for individual gases and their mixture. In the tests for individual gases, 20% and 76% of $NO_x$ was removed at 1 bar and 10 bar, respectively. Even higher removal efficiencies were achieved for $SO_2$, and also these were maintained for longer as the pressure increased. In the tests for $SO_2$ and $NO_x$ mixture, the removal efficiency of $NO_x$ increased from 13% at 1 bar to 56% at 20 bar because of higher solubility at elevated pressures. $SO_2$ in the mixture was initially dissolved almost completely and then increased by 1,219 ppm at 1 bar and by 165 ppm at 20 bar. Overall, the removal efficiency of $SO_2$ and $NO_x$ was increased at elevated pressures, but it was lower in the mixture compared with individual gases at identical conditions because of a lower pH and associated chemical reactions in water.

• Composites Research
• /
• v.32 no.3
• /
• pp.148-157
• /
• 2019

In this study, $C_f/SiC$, $SiC_f/SiC$ and $C_f-SiC_f/SiC$ ceramic composites reinforcing carbon fiber, SiC fiber and hybrid fiber were fabricated by hybrid TGCVI and PIP process. After the thermal shock cycle, 3-point bending and Oxy-Acetylene torch test, their mechanical behavior, oxidation and erosion resistance were evaluated. The $C_f/SiC$ composite showed a decrease in mechanical property along with increasing temperature, a pseudo-ductile fracture mode and a large quantity of erosion. The $SiC_f/SiC$ composite exhibited stronger mechanical property and lower erosion rate compared to the $C_f/SiC$, but brittle fracture mode. On the other hand, hybrid type of $C_f-SiC_f/SiC$ composite gave the best mechanical property, more ductile failure mode than the $SiC_f/SiC$, and lower erosion rate than the $C_f/SiC$. During the Oxy-Acetylene torch test, the $SiO_2$ formed by reaction of the SiC matrix with oxygen prevented further oxidation or erosion of the fibers for $C_f-SiC_f/SiC$ and $SiC_f/SiC$ composites particularly. In conclusion, if a hybrid composite with low porosity is prepared, this material is expected to have high applicability as a high temperature thermo-structural composite under high temperature oxidation atmosphere by improving low mechanical property due to the oxidation of $C_f/SiC$ and brittle fracture mode of $SiC_f/SiC$ composite.

• Korean Journal of Materials Research
• /
• v.6 no.7
• /
• pp.700-708
• /
• 1996

Electroless plating technique was utilized to flip chip bonding to improve surface mount characteristics. Each step of plating procedure was studied in terms pf pH, plating temperature and plating time. Al patterned 4 inch Si wafers were used as substrstes and zincate was used as an activation solution. Heat treatment was carried out for all the specimens in the temperature range from room temperature to $400^{\circ}C$ for $30^{\circ}C$ minutes in a vacuum furnace. Homogeneous distribution of Zn particles of size was obtained by the zincate treatment with pH 13 ~ 13.5, solution concentration of 15 ~ 25% at room temperature. The plating rates for both Ni-P and Au electroless plating steps increased with increasing the plating temperature and pH. The main crystallization planes of the plated Au were found to be (111) a pH 7 and (200) and (111) at pH 9 independent of the annealing temperature.

• Horticultural Science & Technology
• /
• v.34 no.6
• /
• pp.886-897
• /
• 2016

The physical properties of rooting media for the establishment of plugs in a greenhouse are modified according to variations in the greenhouse environment throughout the season. In this study, we established a standard for rooting media for the production of plug seedlings for each growing season (summer, winter and spring fall). Eight types of peatmoss (PM) and 4 types of perlite (PL) commonly used in Korea were collected and blended with the ratio of 7 parts PM to 3 parts PL (v/v) to make 32 different rooting media blends. We determined the total porosity (TP), container capacity (CC), air-filled porosity (AFP), pH, and electrical conductivity (EC) of the 32 media blends, and 6 media blends were selected for seasonal use. We also conducted additional analyses for plant easily available water (EAW), buffering water (BW), cation exchange capacity (CEC), and nutrient contents in the 6 media blends. The TP, CC, and AFP of the 32 media blends ranged from 64.7 to 96.0%, 42.9 to 90.1%, and 1.3 to 27.8%, respectively, indicating that the physical properties were strongly influenced by the type of PM and PL. The pH and EC of the PMs ranged from 2.96 to 3.81 and 0.08 to $0.47dS{\cdot}m^{-1}$, respectively. However, after blending the PM with the PL the pH was raised and the EC was lowered The media blends selected for the summer growing season were Blonde Golden peatmoss (BG) + No. 1 perlite size < 1 mm (PE1) and Latagro 0-10 mm (L1) + No. 2 perlite size 1-2 mm (PE2). These two media blends had 89.8-90.9% of TP, 80.8-81.3% of CC, and 9.0-9.7% of AFP. The media blends selected for the winter growing season were Sfagnumi Turvas (ST) + PE2 and Latagro 20-40 mm (L3) + PE2. These media blends had 79.9-86.7% of TP, 60.4-74.9% of CC, and 11.8-19.6% of AFP. The TP, CC, and AFP of two media blends, BG + No.3 perlite 2-5 mm (PE3) and Orange peatmoss (O) + PE3, selected for the spring and fall growing seasons, respectively, were 85.2-87.3%, 77.9%, and 7.4-9.4%, respectively. The percentage of EAW of the media blends selected for the spring, summer, and winter growing seasons ranged from 24.2-24.9%, 22.0-28.6%, and 18.0-21.8%, respectively, but the percentages of BW were not significantly different among the selected root media blends. The pH, EC, and CEC of the 6 selected media blends ranged from 3.11-3.97, $0.06-0.26dS{\cdot}m^{-1}$, and $97-119meq{\cdot}100g^{-1}$, respectively.

• KSBB Journal
• /
• v.23 no.4
• /
• pp.323-328
• /
• 2008

This study was accomplished using Anaerobic/Anoxic/Oxic biofilm reactors with fixed media and post-treatment reactor for natural purification with aquatic floating plants. The objectives of this study was to investigate the characteristics of organics, nitrogen and phosphorus removal from sewage with the HRT. The average removal efficiency of SS and $COD_{Cr}$ increases as increasing the hydraulic retention time (HRT) until 12 hr of the HRT, and it was constant over 12 hr of the HRT. The removal efficiency of them was about 93% and 89% respectively over the 12 hr of HRT. The average $BOD_5$ and $COD_{Mn}$ increases as increasing the HRT and the removal efficiency of them was 84.91 % and 76.03% respectively at the 26 hr of HRT. The removal efficiency of T-N and T-P increases as increasing the HRT until 61 hr of the HRT, and it was constant over 61 hr of the HRT. At the HRT of 61 hr, it was 70.20%, 77.86% respectively. It was found that the optimum HRT was 61 hr in case of the nutrients. Before and after experiment, the nitrogen content was similar in leaves of the water hyacinths but the nitrogen content in roots after experiment was 5.5% more than its content before experiment. It was known that the nitrogen was absorbed by the water hyacinths.

• Korean Journal of Food Science and Technology
• /
• v.44 no.3
• /
• pp.263-268
• /
• 2012

Novobiocin is a coumarin-containing antibiotic, and has a longer half-life in various animals than other veterinary medicines. A simple and rapid high-performance liquid chromatography assay for the determination of residual novobiocin levels in chicken, beef and milk has been developed and validated. The separation condition for HPLC/UVD was optimized by a MG II $C_{18}$ (4.6 mm $ID{\times}250$ mm, 5 ${\mu}m$) column with 0.1% formic acid in $H_2O$/0.1% formic acid in Acetonitrile (40/60, v/v) as the mobile phase at a flow rate of 1.0 mL/min and the detection wavelength was set at 340 nm. Residues were extracted from tissue by blending with methanol. After liquid-liquid partitioning, lipid materials were removed with n-hexane and purification as Silica (1 g, 6 mL) cartridge with 10 mL acetone/dichloromethane (10/90, v/v). Limit of quantification and linearity performed by the analytical method were 0.02 mg/kg and 0.999 ($r^2$), and the recovery range was $88.8{\pm}5.6-100.3{\pm}4.4$, $88.8{\pm}7.2-97.0{\pm}3.2$ and $88.1{\pm}4.3-92.8{\pm}3.6%$. It is expected that this analytical method with regards to novobiocin in chicken, beef and milk could be applied as an official method to administer food safety on veterinary medicines.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.178-184
• /
• 2001

Transparent and highly oriented KLN thin films have been grown by an rf- magnetron sputtering deposition method. A homogeneous and stable KLN target was prepared by calcine and sintering process. For KLN target, stoichiometry and composition excess with K of 30% and 60%, and Li of 15% and 30% respectively, was prepared. The targets were sintered at low temperature to prevent vaporization of K and Li. KLN thin films were fabricated by rf-magnetron sputtering method using those targets. In this experiment, using the target of composition excessed with K of 60% and Li of 30%, single phase KLN thin film was produced. KLN thin film has excellent crystallinity and highly c-axis oriented on Corning 1737 substrate. Transmittance of thin film in visible range was 90%, absorption edge is 333 nm and refractive index at 632.8 nm was 1.93.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.3
• /
• pp.83-88
• /
• 2015

Coating materials used in the electron beam (EB) deposition method, which is being studied as one of the fabrication methods of thermal barrier coating, are exposed to high power electron beam at focused area during the EB deposition. Therefore the coating source for EB process is needed to form as ingot with appropriate density and microstructure to sustain their shape and stable melts status during EB deposition. In this study, we tried to find the optimum powder condition for fabrication of ingot of 8 wt% yttria stabilized zirconia which can be used for EB irradiation. It seems that the ingot, which is fabricated through bi-modal type initial powder mixture which consists of tens of micro and nano size particles, was shown better performance than the ingot which is fabricated using monolithic nanoscale powder when exposed to high power EB.

• Microbiology and Biotechnology Letters
• /
• v.41 no.3
• /
• pp.327-334
• /
• 2013

For the development of hardy kiwi wine, we arranged for the post-maturity of hardy kiwi fruit, treated them with calcium carbonate and a pectinase enzyme complex, investigated the resulting physicochemical properties and conducted a sensory evaluation. The period determined for creating post-maturity in the hardy kiwi fruit was determined as 5 days storage at room temperature following maturity. During this time the yield of fruit juice was increased from 22.1% to 53.5% using 0.1% (v/v) cytolase PCL5 for 2 h at room temperature. 0.1% (w/v) calcium carbonate was also added during the process of aging, for the reduction of the sour taste. The fermentation trial of the hardy kiwi wine was prepared using water (25% or 50%), sugar ($24^{\circ}brix$), 0.1% (w/v) $CaCO_3$, 0.1% (v/v) cytolase PCL5, $K_2S_2O_5$ (200 ppm), and yeast ($1.5{\times}10^7$ cell/ml). Fermentation then occurred for 2 weeks at $20^{\circ}C$. The pH value, total acidity, alcohol, and reducing sugar content of the resulting hardy kiwi wines of 25% (v/w) and 50% (v/w) water, were in a range of pH 3.4-3.7, 1.12-1.21%, 14.3-14.4%, and 15-16 g/l, respectively. Citric acid and fructose constituted the major organic acids and the free sugar of the 25% and 50% hardy kiwi wine, respectively. Volatile flavor components, including 10 kinds of esters, 8 kinds of alcohols, 5 kinds of acids, 3 kinds of others and aldehydes, were determined by GC analysis. The results of sensory evaluation demonstrated that 50% hardy kiwi wine is more palatable than 25% hardy kiwi wine.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.872-879
• /
• 2010

Layered copper hydroxides [LCHs, $Cu_2(OH)_3{\cdot}NO_3$] has the agricultural potentials as a fungicide because of its high crystallinity, excellent anion exchange capacity, and its regular layered particle size. The study, for the first time, has synthesized LCHs in highly concentrated solution and evaluated its physicochemical properties including the crystallinity and suspension stability. Optimal synthetic condition of LCHs was determined by crystallinity and stability of suspension as follow; 1) concentrations of $Cu(NO_3)_2$ and NaOH solutions were 3.0 M respectively, 2) reaction temperature and solution pH were $25^{\circ}C$ and 6.0, respectively, and 3) aging time after reaction was 2hr. Crystallinity of LCHs enhanced with increase in pH up to 9.0. Whereas, stability of suspension was decrease by increase in crystal size. Especially, increase in reaction temperature decreased stability of suspension. XRD patterns and SEM images exhibited that LCHs had regular layered particle size with 0.2~0.8 ${\mu}m$ and high crystallinity in optimal synthetic condition. The particle size was increased with increase in reaction temperature and pH. These results showed that LCHs synthesized in highly concentrated solution exhibited high stability of suspension as well as high crystallinity suitable to their potential as a fungicide.