• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.1
• /
• pp.535-540
• /
• 2006

The relationship between the observable noise model and the satellite elevation angle can be modeled quite well by an exponential function.[Jin, 1996] Noise size and dependence on the elevation angle are, however, different for each observation and receiver type. Therefore, the coefficient determination of this model is an issue, and various methods including PR-CP, single difference, and time difference have been suggested. The limitations of them are difficulty to model the carrier phase noise and to eliminate bias. To overcome these disadvantages for using Jin's model, we suggest zero baseline double difference (DD) and noise sorting algorithm. Data DD technique in zero baseline is useful to eliminate all the troublesome GPS biases, and the remaining error is the sum of GPS measurement noises from two satellites. These DD residuals for hours should be sorted by the combination of satellite elevation angles, and then variance value of the residual for each combination can be estimated. Using these values, we construct an over-determined linear equation whose solution is a set of noise variance for each satellite elevation angle. With 24hr Trimble 4000ssi data, we easily worked out the coefficients of the noise model not only for pseudorange but also for carrier phase. We estimated the standard deviation of the measurement DD using our model, and plotted 1 and 3 sigma lines for every epoch to verify the representation of the residual error. 63.3% of pseudorange residual and 65.9% of phase error did not exceed the 1 sigma lines. Additionally, 99.2% and 99.5% of them lied within 3sigma line. These figures prove that the Gaussian property of measurement noise, and that the suggested model by our algorithm corresponds to the observable noise information.

• 한국주조공학회지
• /
• 제33권5호
• /
• pp.215-225
• /
• 2013

The alloys required for fossil power plants are altered from stainless steel that has been used below $600^{\circ}C$ to Ni-based alloys that can operate at $700^{\circ}C$ for Hyper Super Critical (HSC) steam turbine. The IN740 alloy (Special Metals Co. USA) is proposed for improved rupture strength and corrosion resistance at high temperature. However, previous studies with experiments and simulations on stable phases at about $700^{\circ}C$ indicated the formation of the eta phase with the wasting of a gamma prime phase, which is the most important reinforced phase in precipitation hardened Ni alloys, and this resulted in the formation of precipitation free zones to decrease the strength. On the basis of thermodynamic calculation, the new Ni-based superalloy named LESS 1 (Low Eta Sigma Superalloy) was designed in this study to improve the strengthening effect and structure stability by depressing the formation of topologically close packed phases, especially sigma and eta phases at high temperature. A thermal exposure test was carried out to determine the microstructure stability of LESS 1 in comparison with IN740 at $800^{\circ}C$ for 300 hrs. The experimental results show that a needle-shaped eta phase was formed in the grin boundary and it grew to intragrain, and a precipitation free zone was also observed in IN740, but these defects were entirely controlled in LESS 1.

• 한국해양공학회지
• /
• 제23권4호
• /
• pp.52-57
• /
• 2009

The effect of aging treatment on the microstructure and mechanical properties of super duplex stainless steel with W was investigated. The phase was precipitated mainly at the early stage of aging and a lower aging temperature under $750^{\circ}C$, but the phase was formed after long-term aging treatment between $600^{\circ}C$ and $900^{\circ}C$. The volume fraction of the phase increased with aging temperature up to $750^{\circ}C$ and then decreased up to $900^{\circ}C$. With an increase in the aging time, the volume fraction phase at the early stage of aging increased slightly, and then increased rapidly beyond a certain time. The rapid increase in the tensile strength and hardness and decrease in the elongation and impact toughness were measured with aging temperatures up to $750^{\circ}C$. On the other hand, the tensile strength and hardness decreased slightly, and the elongation and Charpy impact toughness were unchanged with aging temperatures over $750^{\circ}C$. The tensile strength and hardness increased rapidly at the early stage of aging, and then increased slowly beyond a certain time. The elongation and Charpy impact toughness decreased rapidly at the early stage of aging, and then remained unchanged beyond a certain time. The phase that formed at the early stage of aging and the lower aging temperature had a considerable effect on the elongation and Charpy impact toughness of the super duplex stainless steel with W.

• 열처리공학회지
• /
• 제12권4호
• /
• pp.320-326
• /
• 1999

In rapidly solidified $Al_{92-x}Nd_8$(Cu,Ag)x ($0{\leq}X{\leq}10at%$) alloys, amorphous single phases were obtained in the ranges of $Oat%{\leq}X{\leq}4at%$ for Al-Nd-Cu system and $Oat%{\leq}X{\leq}6at%$ for Al-Nd-Ag system, respectively. Mesoscopic structures consisted of amorphous and crystalline phases were formed above solute ranges. It was founded that the mesoscopic structures were also formed near 1st exothermic peak on DSC curve by aging in amorphous single phase alloys. For example, amorphous $Al_{92-x}Nd_8$(Cu,Ag)x (X=2.4at%) alloys containing nanoscale Al particles and compounds, i.e., mesoscopic structure, exhibited higher tensile fracture strength(${\sigma}_f$) than those of amorphous single phase alloys with the same composition. The ${\sigma}_f$ showed a maximum value in the $V_f$ ranges of 10~15%. The reason is presumed that the nanoscale precipitates which have higher mechanical strength compared with the amorphous phase with the same composition act as an effective resistance to shear deformation of the amorphous matrix.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2006년도 정기학술발표대회 논문집
• /
• pp.478-482
• /
• 2006

국내 기업들은 치열한 국제경쟁력에서 시장의 선도적 위치를 확보하기 위하여 가격 및 품질 우위 전략을 꾸준히 추진하고 있다. 건설산업에서도 건설시장 개방에 따른 해외기업들과의 경쟁 상황에 놓이게 되면서 기업의 경영전략, 방향 및 핵심결정요소들에 대한 연구에 여념이 없으며, 따라서 무엇보다도 기업의 경쟁력 강화가 중요한 우선순위에 오르게 된다. 이러한 기업의 경쟁력 강화를 위하여 많은 기업으로부터 큰 관심을 유도하고 있는 기법이 6시그마(Sigma) 기법이다. 6 시그마 기법의 선행 연구들은 제조업과 서비스업을 대상으로 수행된 것이 대부분이다. 건설업과 관련한 연구는 6시그마의 도입 및 고찰 단계에 머물러 있으며, 실제 도입은 "S건설" 1개사만 도입하여 적용하고 있기 때문에 그 적용 성과에 대하여는 한계를 가질 수밖에 없다. 그렇지만 상기에 언급한 것처럼 시장 환경의 급격한 변화에 따른 국제 경쟁력 확보를 위하여 6시그마 도입은 필수적이라 판단하고, 이에 대한 논리적 타당성의 전개 및 이를 검증하기 위한 설문조사를 통하여 건설깅버의 6시그마 적용 가능성을 확인함으로서 6시그마 도입 적용의 한계성을 극복하는 것이 본 연구의 목적이라고 할 것이다.

• 대한전자공학회논문지SD
• /
• 제47권12호
• /
• pp.75-82
• /
• 2010

본 논문은 다중대역 송수신기 CMOS RFIC 단일 칩을 위한 광대역 델타시그마 분수분주형 주파수합성기에 관한 것이다. 광대역 VCO의 LC Tank에 6-bit Switched Capacitor Array Bank를 작용하여 2340~3940 MHz의 출력주파수 범위를 가지도록 하였으며, 위상동기 전 Capacitor Bank Code를 선택하기위한 VCO Frequency Calibration 회로는 전체 주파수대역에서 $2{\mu}s$이하로 보정을 마치는 뛰어난 성능을 보여준다. 광대역 VCO로부터 T-DMB/DAB/FM Radio의 LO 신호를 생성하기 위해 선택 가능한 다중분주비 ${\div}2$, ${\div}16$, ${\div}32$를 가지는 LO 신호 발생기는 L-Band (1173 ~ 1973 MHz), VHF-III (147 ~ 246 MHz), VFH-II (74~123 MHz)에서 I/Q신호를 생성한다. Integrated Phase Noise는 전체 대역에서 0.8 degree RMS 이하로 측정되어 매우 낮은 위상잡음을 보여주었다. 또한, VCO Frequency Calibration 시간을 포함하는 주파수합성기의 전체 동기시간은 $50{\mu}s$ 이하로 측정되었다. 이 광대역 델타시그마 분수분주형 주파수합성기는 $0.13{\mu}m$ CMOS공정으로 제작되었으며, 1.2 V 전원전압에서 15.8 mA의 전류를 소모한다.

• 전자공학회논문지
• /
• 제54권5호
• /
• pp.24-32
• /
• 2017

본 논문에서는 생체 신호 처리를 위한 12비트 이상의 고 해상도를 갖는 저 전력 CMOS 4차 델타-시그마 변조기를 설계하였다. 제안하는 4차 델타-시그마 변조기는 시간 분할 기법을 이용하여 회로를 시간에 따라 재구성해 4개의 연산증폭기가 필요한 회로를 1개의 연산증폭기만으로 구동 시켰다. 이를 통하여 일반적인 구조보다 전력소모를 75% 감소시킬 수 있다. 또한 kT/C 잡음과 칩 면적을 고려하여 변조기의 입력단과 출력 단의 커패시터들을 안정적으로 구동하기 위하여 적분기내 가변되는 증폭기를 설계하였다. 첫 번째와 두 번째 클럭 위상에서는 2단 연산 증폭기가 동작하고, 세 번째와 네 번째 위상에서는 1단 연산 증폭기가 동작한다. 이로 인하여 두 가지 위상 조건에서 연산증폭기의 위상여유가 60~90도 이내에 존재하게 하므로서 변조기의 안정성을 크게 향상시켰다. 제안한 변조기는 $0.18{\mu}m$ CMOS N-well 1 poly 6 metal 공정을 이용하여 제작되었으며, 1.8V의 공급전압에서 $354{\mu}W$의 전력소모가 측정되었다. 256kHz의 동작주파수, 128배의 오버샘플링 비율 조건에서 250Hz의 입력 신호를 인가하였을 때, 최대 SNDR은 72.8dB, ENOB은 11.8 비트로 측정되었다. 또한 종합 성능 평가지수인 FOM(Walden)은 49.6pJ/step, FOM(Schreier)는 154.5dB로 측정되었다.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.248-261
• /
• 1999

The fatigue life of mechanical components and structures has been influenced by mechanical, material and environmental conditions. It is important to search out the load type and size for accurate cause of fracture at the damaged surface of material. The fractographic method by x-ray diffraction can utilize residual stress $\sigma$_r and half-value breadth B and find out the types and the mechanical conditions of fracture. This study showed the relationship between fracture mechanical parameters $\Delta$K, $K_{max}$ and X-ray residual stress $\sigma$_r for normalized SS41 steel with homogeneous crystal structure and M.E.F. dual phase steel(martensite encapsulated islands of ferrite). The fatigue crack propagation tests were carried out under stress ratios 0.1 and 0.5. The x-ray diffraction technique according to crack propatation direction was applied to fatigue fractured surface. Residual stress $\sigma$_r was independent on stress ratios by arrangement of $\Delta$K. The equation of $\sigma$_r$\Delta$K was established by the experimental data. Therefore, fracture mechanical parameters can be estimated can be estimated by the measurement of X-ray parameters.

• Industrial Engineering and Management Systems
• /
• 제11권4호
• /
• pp.346-352
• /
• 2012

While systems engineering has been widely applied to complex system development, some evidences are reported about major budget and schedule overruns in systems engineering applied. On the other hand, many organizations have been deploying Design for Six Sigma (DFSS) to build Six Sigma momentums in the area of design and development for their products and processes. To explore the possibility of having a DFSS complement systems engineering process, this process reviews the systems engineering with their categories of effort and DFSS with its methodologies. A comparison of the systems engineering process and DFSS indicates that DFSS can be a complement to systems engineering for delivering higher quality products to customers faster at a lower cost. We suggest a simplified framework of systems engineering process, that is, PADOV which was derived from the generic systems engineering process which has been applied to the development of T-50 advanced supersonic trainer aircraft by Korea Aerospace Industries (KAI) with technical assistance of Lockheed Martin. We demonstrated that each phase of PADOV framework is comprehensively matched to the pertinent categories of systems engineering effort from various standards.

• Journal of Microbiology and Biotechnology
• /
• 제3권3호
• /
• pp.146-155
• /
• 1993

A DNA fragment from an alkali-tolerent Bacillus sp., conferring strong promoter activity, was subcloned into the promoter probe plasmid pPL703 and the nucleotide sequence of this promoter region was determined. The sequence analysis suggested that this highly efficient promoter region containing the complex clustered promoters comprised three kinds of promoters (P1, P2 and P3), which are transcribed by $\sigma^B (formerly \sigma^{37}), \sigma^E(formerly \sigma^{29}) and \sigma^A (formerly \sigma^{43})$ RNA polymerase holoenzymes which play major rules at the onset of endospore formation, during sporulation and at the vegetative phase of growth, respectively. S1 nuclease mapping experiments showed that all three promoters had staggered transcription initiation points. The results of chloramphenicol acetyltransferase assay after the subcloning experiments also indicated that the expression of these clustered promoters was correlated with the programs of growth and endospore development. Promoter P1, P2 and P3 were preceded by 75% AT, 79% AT and 81% AT regions, respectively, and a partial deletion of AT-rich region prevented transcription from promoter P1 in vivo. Two sets of 5 -AGTGTT-3 sequences and inverted repeat sequences located around the promoter P1 were speculated as the possible cis acting sites for the catabolite repression in B. subtilis. In vivo transcripts from these sequence regions may be able to form a secondary structure, however, the possibility that a regulatory protein induced by the excess amount of glucose could be bound to such a domain for crucial action remains to be determined.