The key points of the CTP board is as follows: Film, brightness, plate exposure is eliminated, the reduction of personal expenses, and the reduction of time consumption. But above all, the accurate reappearance of the highlighting and shadow portion as well as self modification of the dust edge portion stands out as the most impressive improvements. In this paper, using a digital test from 4.0 and a Thermal CTP color printing control, the two parts of the Thermal CTP utilized a 1%-99% dot reappearance. Also, using an opposite line target, the results of the CTP plates and printing were compared. Finally, research was made on the printing quality on the slur development of the plate and the result when there was a lack of weave connection.

Recently as color image processing to be become independent have been desired at the light source in an image processing and it have been enlarged. An image processing of the light source which is become independent means an image processing which uses a spectral reflectance information. We improved it in the spectral reflectance estimation method which uses existing 3-band image in this research that the improvement of an identity color population generation method which uses the hue angle and the processing speed improvement and introduces a labelling method. The precision of a spectral reflectance estimation appeared to the ${\Delta}E^*_{ab}$ of an average 2.7 comparing with the measurement price. The practical use possibility came to be fast and appeared a processing speed compared with existing method.

A piece of coating color or base paper picked during printing is called coating pick. Loosely bonded materials of coating color or broken piece of fiber could be adhered to the blanket or would be mixed with ink during printing. Because the coating pick can make troubles in printing press such as piling, hickey and collecting, the coating pick of a paper has been one of the most serious problems in printing. In this paper, two influential factors to the coating pick in the printing, those are latex content and ash content of the coating color, are studied. The surface resistance of coating paper is directly proportional to the latex content, otherwise inversely proportional to the ash content. We propose a different way to evaluate the picking and used a homemade pick test device.

With increasing interests in environment matters over the world, incessant efforts to develop products which meet these environmental requirements have been made also in paint industry. Among the efforts in this field, UV(Ultra Violet) curing system is focused as one of most potential system. It is because this system not only proved to be environmentally friendly compared with heat curing system or other system but also has economical merit of smaller facility, less energy consumption, and better productivity. Superior properties in many application is surely one of its dominant merit. With these advantage UV system is applied to a variety of industrial fields and expected to have continuous growth in the future. As practical application of UV system has shown lasting progress, R&D on basic material of this system keeps up with. This is a study on photo-initiator that is a fundamental substance in UV curing method and amine, its aid for better effect. After reviewing on them in the aspects of function, economy, and stability, optimal foumula is pursued through experiments when applied to real products.

A novel evaluation method is investigated for measuring the ability of acid amplification of acid amplifier. The method is based on the measurement of conductivity change by the acid generation according to UV radiation. It is found that the decrease of conductivity is caused by photopolymerization of epoxy monomer during UV curing process of ink film and the by the rate of UV curing. In this paper, the novel acid amplifiers were synthesized and measured thermal stability by means of DSC. It was found that mono-type acid amplifiers were more stable than di-type. It is possible to make the dynamical evaluation the curing rate of UV curable ink in curing process by this method.

The CRT(cathode ray tube) in oscilloscope consists of an electron gun, horizontal vertical deflection system and a phosphor screen. When the electron beam strikes the phosphor screen, the phosphor generates light. The phosphor screen has formed by CRT precipitation method. But, this method has some defects that are complex process, low yield, much consumption of raw-material, dirty working environment, waste problem, require of high cost. Moreover phosphor for oscilloscope used at present has been imported from Japan. Therefore developments of new phosphor and new method(the screen printing) top form phosphor screen for oscilloscope are required to improve these matters. This study was developed novel method(the screen printing) to form the phosphor screen for oscilloscope used new phosphor. This screen printing method has advantages of simple process, high yield, clean working environment, saving raw material and running-cost.

This study analyzed the main bodies, sizes of litters, spaces between letters, Words, lines, length of lines, sizes of main body and margin, Position of the main bodies of PDF(Portable Document Format) in high schools and "the criteria of reading system for the textbooks" which was suggested by the Department of Education and Provided some suggestions for the improvement. First, it is judged that spaces of the main body of textbooks should be shrunken to make the ratio of 50:50 between the main body and space margin. Second, it is judged that the main body should be placed in the center of text page. Third, the results of the above findings showed that it would be difficult to deal with the task of deciding space and position or the main body and marginal space in a form of single project, because there are many variables involved and psychologically complicated elements which can not be measured objectively.

The photoluminescence and electroluminescence of poly(9-vinylcarbazole) (PVCz) containing different ratio 1.3,5-dimethly-3,5-di-tert-butyl-4,4-diphenoquinone (MBDQ), 1.3,5-diemthyl-3.5-di-tert-butyl-4,4-stylbenquinone (MBSQ) were characterized. As the contents of DQ and SQ increased, the intensity of peaks at 516 and 540nm increased in PL spectra. The results of TOF measurement were shown that the hole mobility of PVCz decreased as the ratio of DQ or SQ increased. On the other hand, the electron mobility of PVCz increased. Therefore Electron transport is more favorable than hole transport in these charge transfer complexes, due to the stronger localization of the holes. Evidence for better electron transport is the higher mobility of electrons in pure DQ or SQ compared to hole mobility in pure PVCz, and lower DQ or SQ concentration required for equivalent mobilities in the charge-transfer complexes.

PSR ink is used to insulation coating material that heat resistance is. The use purpose is used for bridge prevention, circuit protection, stabilization of insulation. Heat-cured resin was used mainly on the materials of PSR inks. But, UV-curing type resin in used. Also, because of recently environmental problem, ink is going to water type. Purpose of this study is to develop PSR ink that can develop in pure water. and experiment did that do from that find suitable oligomer and monomer and does brand ratio differ. Specially Knew that is extent water soluble UV resin develop possible is DPHA 10~50% that A/A1924 is 50~90wt %, monomer. As a result, when ratio of A/A1924 and DPHA low viscosity epoxy resin is 5:1.5:1.5, could get high sensibility pattern repeatability, tack and alkali-resistance.