• The Journal of the Acoustical Society of Korea
• /
• v.24 no.1E
• /
• pp.7-15
• /
• 2005

This paper addresses issues encountered in measuring the general, 6-degree-of-freedom motion of a human head, A complete mathematical description for measuring the head motion using the six-accelerometer configured bite-bar is suggested, The description shows that the six-axis vibration cannot be completely obtained without the roll, pitch and yaw angular velocity components, A new method of estimating the three orthogonal (roll, pitch and yaw) angular velocities from the six acceleration measurements is introduced. The estimated angular velocities are shown to enable further quantitative error analysis in measuring the translational and angular accelerations at the head. To make this point clear, experimental results are also illustrated in this paper. They show that when the effects of angular velocities are neglected in the head vibration measurement the maximum percentage errors were observed to be more than $3 \%$ for the angular acceleration of the head and to be close to $5 \%$ for its translational acceleration, respectively. It means that the inclusion of all the angular velocity dependent acceleration components gives more accurate measurement of the head vibration.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.6
• /
• pp.814-819
• /
• 2010

This paper is presented to study the error minimization of angular velocity for AGV(autonomous ground vehicle). The error minimization of angular velocity is related to localization technique which is the most important technique for autonomous vehicle. Accelerometer, yaw gyro and electronic compass have been used to measure angular velocity. And methods for error minimization of angular velocity have been actively studied through probabilistic methods and sensor fusion for AGVs. However, those sensors still occure accumulated error by mathematical error, system characters of each sensor, and computational cost are increased greatly when several sensor are used to correct accumulated error. Therefore, this paper studies about error minimization of angular velocity that just uses encoder and gyro. To experiment, we use autonomous vehicle which is made by ourselves. In experimental result, we verified that the localization error of proposed method has even less than the localization errors which we just used encoder and gyro respectively.

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.836-844
• /
• 2000

In this research any abnormal motion of a vehicle is detected by utilizing the difference between the reference and actual yaw velocities as sell as the information on vehicle slip angle and slip angular velocity. This information is then used as a criterion for execution of the yaw moment control. A yaw moment control algorithm based on the brake control is proposed for improving the directional stability of the vehicle. The controller executes brake controls to provide each wheel with adequate brake pressures, which generate the needed yaw moment. It is shown that the proposed yaw moment control logic can provide excellent cornering capabilities even on low friction roads. This active control scheme can prevent a vehicle from behaving abnormally, and can assist normal drivers in coping with dangerous situations as well as experienced drivers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1426-1437
• /
• 2002

Using the Lagrangian explicit time-integration finite element code NET3D which can treat three-dimensional high-velocity impact problems, oblique penetration processes of long rod projectile with yaw against thin plate are simulated. Through the comparison of simulation result with experimental result and other code's computational result, the adaptability and accuracy of NET3D is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. Main research contents to be handled in this paper include the followings. First, the accuracy and efficiency estimation of NET3D code result obtained from the oblique penetration simulations of long rod projectile with yaw against thin plate. Second, the effect of increasing impact velocity. Third, the effect of initial yaw for the spaced-plate target. Residual velocities, residual lengths, angular velocities, and final deformed configurations obtained from the NET3D computations are compared with the experimental results and other code's computational results such as Eulerian code MESA and Lagrangian code EPIC. As a result of comparisons, it has been found that NET3D code is superior to EPIC code and MESA code in the prediction capability of residual velocity and residual length of penetrator. The key features obtained from the experiment can be successfully reproduced through NET3D simulations. Throughout the study, the applicability and accuracy of NET3D as a metallic armor system design tool is verified.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.2
• /
• pp.146-150
• /
• 2009

An Intelligent active roll angle controller design algorithm is discussed. The detailed mathematical formulation and analysis are discussed, and then modeling and design method for active roll angle controller are presented. This paper proposes a design method based upon intelligent robust controller design algorithm to control actively roll angle for improving cornering performance problems. The intelligent robust controller is designed for steady speed driving vehicle system model with representation of steering angle and yaw angular velocity parameters for cornering stability. And the detailed formulation and analysis for the objective vehicle system are investigated.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.261-268
• /
• 2013

In this paper, we propose the algorithm that improves the linearity of the walking assistant robot on lateral slopes. The walking assistant robot goes out of the course due to the rotational moment which is caused by the weight of the robot and the slope. To compensate this, we give the weight to each driving axle after comparing the real rotational angular velocity with the target rotational angular velocity which is entered by an user. The results of applying the algorithm to the real walking assistant robot show that the yaw axis deviation of the robot without the algorithm diverges, but the yaw axis deviation of the robot with the algorithm lies within 20cm, which can be recognized as stable. In addition, the changing rate of the course deviation is stabilized and shows no more course deviation, after moving 300cm.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.10
• /
• pp.992-997
• /
• 2009

This paper focuses on the calculation of the missile angular velocity under the reduced sensor condition and its verification using the Flight Motion Simulator(FMS). The missile angular velocity is usually measured by the body gyroscopes, but we assume that the inertial sensors on the missile body are in the absence of pitch and yaw gyroscopes. Under this reduced sensor condition, this paper shows the missile angular velocity can be calculated by using the gimbal seeker gyroscope, the roll body gyroscope, the gimbal angle and its rate. The FMS experiment was carried out to verify the proposed algorithm.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.1
• /
• pp.21-26
• /
• 2013

The objective of this study was to develop a system for handwriting recognition in three dimensions (3D) to authenticate users. While previous studies have used a stylus pen for two-dimensional input on a tablet, this study uses the Wii Remote controller because it can capture 3D human motion and could therefore be more effective means of recognition. The information obtained from a Wii Remote controller included x and y coordinates, acceleration (x, y, z), angular velocity (pitch, yaw, roll), twelve input buttons, and time. The proposed system calculates distances using six features extracted after preprocessing the data. In an experiment where 15 subjects wrote "AIZU" 10 times, we obtained a 94.8% identification rate using a combination of writing velocity, the peak value of pitch, and the peak value of yaw. This suggests that this system holds promise for handwriting-based authentication in the future.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.1
• /
• pp.1-9
• /
• 2013

This paper presents a new control algorithm for dynamic control of a unicycle robot. The unicycle robot motion consists of a pitch that is controlled by an in-wheel motor and a roll that is controlled by a reaction wheel pendulum. The unicycle robot doesn't have any actuator for a yaw axis control, which makes the derivation of the dynamics relatively simple. The Euler-Lagrange equation is applied to derive the dynamic equations of the unicycle robot to implement the dynamic speed control of the unicycle robot. To achieve the real time speed control of the unicycle robot, the sliding mode control and LQ regulator are utilized to guarantee the stability while maintaining the desired speed tracking performance. In the roll controller, the sigmoid-function based sliding mode controller has been adopted to minimize the chattering by the switching function. The LQR controller has been implemented for the pitch control to drive the unicycle robot to follow the desired velocity trajectory in real time using the state variables of pitch angle, angular velocity, angle and angular velocity of the wheel. The control performance of the two control systems form a single dynamic model has been demonstrated by the real experiments.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.2
• /
• pp.81-87
• /
• 2016

This paper presents a new approach to control of stable motion of single wheel driving robot system of a pitch that is controlled by an in-wheel motor and a roll that is controlled by a reaction wheel. This robot doesn'thave any actuator for a yaw axis control, which makes the derivation of the dynamics relatively simple. The Lagrange equations was applied to derive the dynamic equations of the one wheel driving robot to implement the dynamic speed control of the mobile robot. To achieve the real time speed control of the unicycle robot, the sliding mode control and optical regulator are utilized to prove the reliability while maintaining the desired speed tracking performance. In the roll controller, the sigmoid-function based robust controller has been adopted to reduce the vibration by the situation function. The optimal controller has been implemented for the pitch control to drive the unicycle robot to follow the desired velocity trajectory in real time using the state variables of pitch angle, angular velocity, angle and angular velocity of the driving wheel. The control performance of the control systems from a single dynamic model has been illustrated by the real experiments.