• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2004년도 수소연료전지공동심포지움 2004논문집
• /
• pp.293-296
• /
• 2004

고용량 $LiNi_{1-y}M_yO_2$(M=Al, Zn and Ti, y=0.000, 0.005, 0.010, 0.025, 0.050 and 0.100) 양극재료를 합성하기 위하여 연소법을 사용하였다. 합성한 시료들을 X-선회절 분석, 미세구조관찰, 전자침미세분석(EPMA)을 하였다. battery 충${\cdot}$방전기를 사용하여 리튬의 삽입${\cdot}$추출 반응으로 인하여 나타나는 충${\cdot}$방전 곡선의 변화를 조사하였고, 합성한 각 시편에 대해 충${\cdot}$방전 싸이클 수에 따른 방전용량의 변화를 조사하였다. XRD pattern 분석결과 모든 조성에서 $R\bar{3}m$ 구조를 보여주었다. Ni 자리에 Al, Zn, Ti를 치환한 결과 방전용량은 감소하였으나 M=Al 시료는 싸이클 특성이 증가하였다.

• 한국세라믹학회지
• /
• 제49권1호
• /
• pp.84-89
• /
• 2012

Attempts were made to develop a stable gray pigment at reducing atmosphere, substituting Ti in $ZrTiO_4$ with Mn, Fe, Co and Cu The pigment synthesized at $1300~1500^{\circ}C$ by solid state method with the composition of $ZrTi_{1-x-y}A_xB_yO_4$ (x = y = 0.005, 0.015, 0.035, 0.055, 0.075, 0.095, 0.115, 0.135, 0.155, 0.175 and 0.195 mole, A = Mn(III), Fe(III), Co(II, III) and Cu(II) (chromophores), B = Sb (counterion). The pigments were fired at $1400^{\circ}C$ for 3 h with substitute amount changes of Mn, Fe, Co and Cu to $ZrTiO_4$ crystals, and analyzed by Raman spectroscopy to figure out substitute limits. Results indicated 0.035 mole for Mn, 0.115 mole for Fe, 0.015 mole for Co and 0.015 mole for Cu as substitute limits, respectively. Figs. 1, 2, 3, and 4 represent each substitute pigments of Mn, Fe, Co and Cu. Synthesized pigment was applied to a lime and a lime-magnesia glaze at 7 wt% each, and fired at reducing atmosphere of $1240^{\circ}C$, soaking time 1h. Gray color was obtained with CIE-$L^*a^*b^*$ values at 44.55, -0.65, 1.19(Mn), 40.36, -0.90, 0.30(Fe), 42.63, -0.03, -1.49(Cu) and -40.79, -0.28, -0.91(Co), respectively.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권5호
• /
• pp.434-439
• /
• 1997

It this paper, the piezoelectric and electro-induced strain properties of (P $b_{1-}$2x/3/B $i_{x}$ )[N $i_{1}$3/N $b_{2}$3/)$_{0.4}$( $Ti_{0.6}$Z $r_{0.4}$)$_{0.6}$] $O_3$ceramics (x=0, 0.005, 0.02) were investigated with the substitution of B $i^{3+}$, and the feasibility of the application for bimorph actuator was evaluated by measuring the dynamic properties of the piezoelectric bimorph fabricated with above ceramics. Dielectric constant was enhanced with the increase of B $i^{3+}$ substitution, and appeared the maximum value of 5032 at x=0.01 composition. Increasing the substitution of B $i^{3+}$, the electromechanical coefficient( $k_{p}$ , $k_{31}$ ) was increased up to the substitution of 0.5 mol% B $i^{3+}$, showed the value of 0.656, 0.439, respectively. The piezoelectric constant( $d_{33}$ $d_{31}$ ) had the highest value of 344, 825 with the substitution of 0.5 mol% B $i^{3+}$. The strain, generated by 60 Hz AC electric field, had the largest value of 1200($\times$10$^{-6}$ $\Delta$1/1) in the composition with the substitution of 0.5 mol% B $i^{3+}$. The dynamic properties of the bimorph actuator, fabricated with the composition substitution of 0.5 mol% B $i^{3+}$, showed the largest value of 325 $\mu$m at $\pm$150 V square pulse. square pulse.are pulse..

• 한국발생생물학회지:발생과생식
• /
• 제18권1호
• /
• pp.33-41
• /
• 2014

We investigated the process of yolk absorption in Korean rose bitterling, Rhodeus uyekii, and determined the changes in its morphometric characteristics. The R. uyekii from 1 days post hatching (DPH) to 21 DPH, the eye diameter (ED) was 5.4 at 5 DPH. Thereafter, the ED/total length (TL) ratio increased to 10.7 at 21 DPH (p<0.05). The yolk length (YL) decreased from 95.4 to 1.1 by 21 DPH, and this rate of decrease was greater than that for any other dimension (p<0.05). 12 morphometric dimensions/TL for the R. uyekii were measured at each sampling day from 21 DPH to 170 DPH. At just hatching, the average TL and BW were $6.1{\pm}0.09mm$ and $4.9{\pm}0.07mg$, respectively. At 53 DPH, the average TL was $12.9{\pm}0.28mm$ and the average BW was $14.7{\pm}0.72mg$; the total length growth equation was $TL=5.507e^{0.038t}$ ($R^2=0.916$). Further, the body weight growth equation was $BW=3.3647e^{0.0296t}$ ($R^2=0.9354$). The dimensions with regard to body depth showed the greatest growth rates in the external characteristics of the fish (p<0.05). The patterns of the morphometric characteristics measured in this study can be classified in three ways. The patterns were shown to be increased (y=0.0992x+12.07, $R^2=0.8333$), decreased (y=-0.0569x+42.029, $R^2=0.8395$) or maintained (y=0.005x+18.263, $R^2=0.3678$) from 21 DPH to 170. These results will provide useful indices for the successful rearing of the R. uyekii.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.451-451
• /
• 2014

중고온 열전재료로서의 응용 가능성이 높은 HMS (higher manganese silicide)는 높은 제백계수, 낮은 전기저항, 높은 산화 저항성뿐만 아니라 구성 원소가 풍부하며 친환경적인 열전재료이다. HMS는 주로 용해/응고법, 단결정 성장법에 의해 합성되지만, 구조적인 불균질성 및 많은 합성 에너지를 소비하는 단점이 있다. 또한 진성 HMS는 비교적 낮은 열전특성을 나타내기 때문에 도핑에 의한 열전특성의 개선이 필요하다. 본 연구에서는 HMS의 한 종류인 MnSi1.73에 Cr을 도핑한 화합물 MnSi1.73:Crx (x=0, 0.005, 0.01, 0.02, 0.03)를 고상반응(solid state reaction)과 진공 열간압축성형(hot pressing)을 통해 제조하였다. XRD와 Rietveld refinement를 통해 상변화 및 상분율을 분석하였고, 323~823 K까지 전기적 및 열적 특성을 측정하여 열전 성능지수(ZT)를 평가하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권1호
• /
• pp.5-8
• /
• 2009

MgO nanodots have been deposited and formed on top of the substrate surface. Mg was sputtered to form the MgO nanodots on the single crystal substrates by rf-sputtering method and followed by heat treatment in the oxygen ambient. The deposition and formation of MgO nanodots have been controlled systematically using the process variables such as substrate temperature, sputtering time, and rf-power. As the substrate temperature increased from the room temperature the density of MgO nanodots decreased. The optimal conditions of MgO nanodots formation using the rf-sputtering was investigated and the maximum density of more than $230/{\mu}m^2$ on single crystal substrates was obtained when the rf-power of 100 watts was applied for 30 seconds at room temperature. The typical size of MgO nanodots was identified to be <160 nm(diameter) and 4-30nm (height) by atomic force microscopy. The modulated surface morphology was examined through surface images and cross-section analysis and discussed for the artificial pinning sites in the superconducting films.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.450.2-450.2
• /
• 2014

열전재료는 열-전기가 상호 가역적으로 변하는 재료로서, 최근 에너지 변환소재 분야에서 각광받고 있다. 열전재료의 특성 효율은 무차원 열전 성능지수(dimensionless figure of merit, $ZT={\alpha}2{\sigma}T/{\kappa}$)로 나타낼 수 있다. 여기서 ${\alpha}$는 제벡계수(Seebeck coefficient), ${\sigma}$는 전기전도도(electrical conductivity), ${\kappa}$는 열전도도(thermal conductivity), T는 Kelvin 온도를 나타낸다. 500 K에서 800 K까지의 중온 영역에서 우수한 열전특성을 보이는 $Mg_2X$ (X=Si, Ge, Sn)와 이들의 고용체는 성분원소가 독성이 없고, 매장량이 많아 친환경 열전 재료로 각광받고 있다. $Mg_2X$ 고용체 중 $Mg_2Si_{1-x}Ge_x$는 기존 $Mn_2Si$, $Mg_2Ge$, $Mg_2Sn$계 보다 더 우수한 열전 성능지수를 보인다. 다양한 제조 방법들이 시도되고 있으나, 조성설계 및 구조, 성능 조절의 어려움이 있고, Mg의 산화와 휘발 및 Mg, Si, Ge의 융점 차이가 크고 중력 편석과 반응하지 않은 원소들로 인해 제조가 상당히 어렵다. Sb가 도핑된 $Mg_2Si_{0.5}Ge_{0.5}Sb_y$ (y=0, 0.005, 0.01, 0.02, 0.03) 고용체를 고상반응으로 합성하고 진공열간 압축성형을 통해 성공적으로 제조하였다. 고용 상을 확인하기 위하여 X선 회절분석을 실시하였고, 고용체 형성과 도핑에 따른 전기적 특성변화를 평가하기 위해 Hall 효과를 측정하여 전자 이동특성을 분석하였고, 323~823 K까지 전기전도도, 제벡계수, 열전도도의 측정을 통해 열전 성능지수를 평가하였다.

• 한국응급구조학회지
• /
• 제15권3호
• /
• pp.57-70
• /
• 2011

Purpose : The purpose of this study was to reveal some factors of ROSC & survival for cardiac arrests from sport & leisure activities(CASLs). Methods : A retrospective study of the 1,341 out of hospital cardiac arrests(OHCAs) treated by EMS in Gyeonggi Provincial Fire and Disaster Headquarters from January to December in 2008 was conducted. The primary end-point was admission to emergency room. To clarify the factors through comparison of CASLs(n=58) with ROSCs & survivals(n=58), Answer Tree analysis for data mining with the CHAID algorithm was performed and alpha was set at .05. Mean, median, and percentile of time intervals, distances, and age on the 58 CASLs, 75 ROSCs, and 27 survivals(patients admitted to emergency room) were analysed. Results : Fourteen CASLs(24.1%), 41 ROSCs(54.7%), 16 survivals(59.3%) were treated with CPR within 5 min., and only 2 CASLs(3.4%), 11 ROSCs(14.7%), 10 survivals(37.0%) were treated with defilbrillation within 10 min. from arrest. If time recording from arrest to defilbrillation, the patients were classified 81.0%($X^2=9.83$, p=.005) into ROSCs & survivals. And the patients with no history, 100.0%($X^2=5.44$, p=.020). The other patients with no intention, 87.5%($X^2=7.00$, p=.024). Whereas the other patients with intention, treated with CPR after 4 min. from arrest were classified 67.2%($X^2=3.99$, p=.046) into CASLs. Conclusion : CPR within 4 minutes was the most important factor that discriminates between CASLs and ROSCs & survivals to record cardiac arrests-defilbrillation time. CPR within 4 min. from arrest, no history, and no intention were factors for improved ROSC & survival.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.10-14
• /
• 2014

Niobium nitride coatings have many potential thin film applications due to their chemical inertness, good mechanical properties, temperature stability and superconducting properties. In this study, $NbN_x$ coatings were prepared by inductively coupled plasma (ICP) assisted DC magnetron sputtering method on the surface of AISI 304 austenitic stainless steels. Effects of target power were studied on mechanical and chemical properties of the coatings. The coating structure was analyzed by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The coating hardness was measured by micro-knoop hardness tester. The coating thickness was measured using a 3D profiler and wear characteristics were estimated using a ball-on-disk wear tester. The thickness of the $NbN_x$ coatings increased linearly from 300 nm to 2000 nm as the Nb target power increased, and it showed over $HK_{0.005}$ 4000 hardness above Nb target power of 300 W. Hexagonal ${\delta}^{\prime}$-NbN phase and cubic ${\delta}$-NbN phase were observed in the coating films and the hardness of the NbNx coatings was higher when these two peaks were mixed. The corrosion resistance increased with the increase of the Nb target power.

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.92-96
• /
• 2005

YBCO thin films on metal substrates were prepared by the metal-organic deposition using trifluoroacetates (TFA-MOD). To compensate the loss of Ba element from the precursor films due to the reaction with $CeO_2$ cap layer, we have employed Ba-excessive precursor solutions of $YBa_{2+x}Cu_{3}O_{7-{\delta}}$ ($0{\le}x{\le}0.1$). The precursor solutions were dip-coated on the metal substrates with $CeO_2$ cap layer, initially heated up to $400^{\circ}C$, and finally fired at the various high temperatures for 2 h in a reduced oxygen atmosphere. With this approach, YBCO films possessing critical temperature over 85 K could be successfully prepared on the metal substrates. The highest $T_{c,zero}$ value of 86 K was obtained from the Ba-excessive YBCO film of x=0.005 in $YBa_{2+x}Cu_{3}O_{7-{\delta}}$ fired at $750^{\circ}C$ for 2 h. However, unexpected $T_c$ suppression even in Ba-excessive YBCO samples requires further identification.