• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.10 no.1
• /
• pp.104-114
• /
• 2000

This study was carried out to estimate current status of dust concentrations in the factories producing non-metallic products in Korea. Data were gathered from the environmental monitoring reports by 40 workplace environmental monitoring institutes and the questionnaire designed for the study by the authors. A total of 1838 dust samples from 368 plants were obtained from the reports and were analyzed with no data modifications. But data on asbestos, rock wool, and welding fumes were excluded in this evaluation. The factories were classified into eight groups according to the standard industrial classification scheme in Korea. The results of this study were as follows; 1. The factories included were glass, non-refractory ceramic, refractory ceramic ware, structural non-refractory clay and ceramic, cement and lime, articles of concretes, and stone. Mean(geometric mean) concentrations of total dust samples ranged from $1.75(0.84)mg/m^3$ to $5.87(2.84)mg/m^3$. Statistically significantly higher dust concentrations were found in the cement and lime industries compared with other industries. 2. The non-compliance rates were 15.2% in glass and 20.6% in other non-metallic mineral products industries. Although all institutions surveyed utilized the identical sampling and classification scheme for dusts as specified in the current occupational exposure limits, wide discrepancies were found in collecting samples and classifying dusts. Further problems were discovered in classifying dusts. A dust sample collected could be classified into any of the three groups regardless of silica content. The results of this study showed that dust concentrations in the non-metallic products industries varied widely. Also discovered was classification errors of dust types among workplace monitoring institutes. These errors could adversely affect the results of exposure assessments and the true nature of dust hazards. Further, no institutions performed respirable dust sampling and analysis of crystalline silica. In order to correct these malpractices, current standards of occupational exposure limits should be revised and tight supervision by the Ministry of Labour be suggested.

• Journal of Environmental Health Sciences
• /
• v.43 no.4
• /
• pp.324-333
• /
• 2017

Objectives: The purpose of this study was to assess the correlation relationship between personal exposure and urinary hippuric acid in biological monitoring for airborne toluene in an industrial complex and in general environments. Methods: Personal exposure to toluene and its metabolite, hippuric acid, in urine were simultaneously measured in occupational environments area near an industrial complex and in general environments. The study subjects were divided into three types: 137 workers who use organic solvents in the workplace, 210 residents living near a dyeing industrial complex, and 379 residents living in general environments. The toluene exposures of workers and residents were measured by a passive sampler for four days. The urine of participants was sampled when the passive samplers of personal exposure were collected. Results: The toluene and hippuric acid concentrations of workers were the highest, followed by the concentrations of residents living near a dyeing industrial complex and residents living in general environments. The coefficient of correlation between the concentrations of toluene and hippuric acid among workers was 0.749 (p<0.01) in the workplace. On the contrary, correlations between the concentrations of toluene and hippuric acid among residents living near a dyeing industrial complex and residents living in general environments were all not significant. The relationship between the concentrations of hippuric acid and toluene in three types could be described by the exponential growth model. Conclusions: This study analyzed the relationships between toluene exposure and the concentrations of hippuric acid in urine in high, middle, and low exposure environments, and could be described by the exponential growth model.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.2
• /
• pp.272-280
• /
• 1996

This study was to evaluate the associations between urinary S-Phenyl-mercapturic acid(S-PMA) as a new indicator of biological monitoring for low level of exposure to benzene and independent variables such as the air concentration of benzene in the breathing zone of workers, the years of work, and smoking. In this study the subjects were the total of 145 drawn from 53 workers who were occupationally exposed to benzene and 92 workers who were not. The results were as follows: 1. In the workplace geometric mean concentration of benzene in the breathing zone of workers was 0.31 ppm(0.02 - 3.26 ppm) for the spraying workers and 0.25 ppm(0.02 - 3.95 ppm) for the printing workers. 2. The geometric mean of uninary S-PMA for non exposed group was $8.9{\mu}g/g$ creatinine($0.6-72.3{\mu}g/g$ creatinine), 80.3% (74 workers) of the total non-exposed workers indicated less than $20{\mu}g/g$ creatinine of uninary S-PMA. The difference of uninary S-PMA by sex, age, smoking was not significant. 3. The geometric mean of urinary S-PMA for workers who were exposed to benzene was $37.2{\mu}g/g$ creatinine, and was four times higher than that of workers who were not exposed. And 79.3% (42 workers) of the total exposed workers indicated more than $20{\mu}g/g$ creatinine of urinary S-PMA. 4. Regarding the level of benzene in the air, urinary S-PMA was the highest level of $147.9{\mu}g/g$ creatinine in the workers who were exposed to air concentration of 0.5 ppm of benzene and was higher as the level in the air was increased. 5. The correlation coefficient between log urinary S-PMA and log benzene concentration in the breathing zone was 0.80, and the following linear equation was found between urinary log S-PMA and log benzene concentration in the breathing zone : log S-PMA(${\mu}g/g$ creatinine) = 0.564 log benzene in air(ppm) + 0.192 (n=53, r=0.80, p=0.000) In conclusion, the concentration of S-PMA in urine proved to be good parameter for biological monitoring benzene exposure at the workplace even at low level of benzene in air.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.2
• /
• pp.45-51
• /
• 2018

In this paper, we propose a Designed and Developed home router management system. Through the fourth industrial revolution and development of IoT technology, now people can experience a wide range of IoT related services at their workplace or daily lives. At the industrial site, IoT devices are used to improve productivity such as factory automation, and at home, IoT technology is used to control home appliances from a remote distance. Usually IoT device is integrated and controlled by the router. Home router connects different IoT devices together at home, however when security issues arise, it can invade personal privacy. Even though these threats exist, the perception for home router security is still insufficient. In this paper, we have designed and developed home router management system using DEVS methodology to promote the safe use of home router. Through the DEVS methodology, we have designed the system and developed the mobile application. This management system enables users to set up security options for home router easily.

• Journal of Korea Multimedia Society
• /
• v.22 no.9
• /
• pp.1011-1019
• /
• 2019

In this paper, we propose a system that can more precisely identify and monitor the position of the tool used in the assembling workplace such as automobile production. The proposed positioning monitoring system is a combination of UWB communication module and MEMS IMU sensor. Since UWB does not need modulation and demodulation function and has low power density, UWB is widely used in indoor positioning field. However, it may cause positioning error due to errors in RF transmission and reception process, which may cause positioning accuracy. Therefore, in this paper, we propose an algorithm that uses IMU as an auxiliary means to compensate for errors that may occur in positioning using only UWB. The tag and anchor of UWB module measure the transmission / reception time by transmitting signals to each other and then estimate the distance between tag and anchor. The MEMS IMU sensor serves to provide positioning calibration information. The tag, which is a mobile node and attached to a moving tool, measures the three-dimensional position of the tool and transfers the coordinate data to the anchor. Thus, it is possible to confirm whether or not the specific tool is properly used according to the prescribed regulations.

• Journal of Radiation Protection and Research
• /
• v.38 no.2
• /
• pp.68-77
• /
• 2013

Derived Investigation levels(DILs) were calculated to protect the workers from the effects of both radiological hazard and chemical toxicity by uranium intake. Investigation Levels(ILs) of committed effective dose of 2 mSv $y^{-1}-6$ mSv $y^{-1}$ and uranium concentration of 0.3 ${\mu}g$ $g^{-1}$ in kidney, based on Korean Nuclaer Safety Act, Korean Occupational Safety and Health Act and current scientific studies of uranium intake were assumed. DILs of radiological hazard and chemical toxicity were then calculated based on the concentration of uranium in air of workplace, the lung monitoring and urine analysis, respectively. As a result, in case of the nuclear fuel fabrication plant where 3.5% enriched uranium is handled, derived investigation level(DIL) for the control of the concentration of uranium in the air of workplace assumed with 15-min acute inhalation was 0.6 mg $m^{-3}$ for all types of uranium. DILs for the control of the average concentration of uranium in air of workplace, assuming an 8-hour workday, were 15.21 ${\mu}g$ $m^{-3}$ of Type F uranium, 0.41-1.23 Bq $m^{-3}$ and 0.13-0.39 Bq $m^{-3}$ for Type M and Type S uranium, respectively. DILs for the lung monitoring assumed with a period of 6-month interval were 0.37-1.11 Bq and 0.39-1.17 Bq in acute and chronic inhalation for Type M, respectively and 0.30- 0.91 Bq and 0.19-0.57 Bq in acute and chronic inhalation for Type S, respectively. Since a detection limit of typical germanium detector for the measurement of 235U activity is 4 Bq, DILs calculated for the lung monitoring were not appropriate. DILs for urine analysis, for which an interval was assumed to be 1 month, were 14.57 ${\mu}g$ $L^{-1}$ based on chemical toxicity after acute inhalation. In addition, acute and chronic inhalation of Type M were calculated 2.85-8.58 ${\mu}g$ $L^{-1}$ and 1.09-3.27 ${\mu}g$ $L^{-1}$ based on the radiological hazard, respectively.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.3
• /
• pp.375-383
• /
• 2023

Objectives: Coal-fired power plants feature diverse working conditions, including multi-layered employment structures and irregular work cycles due to outsourcing and non-standardized tasks. The current uniform occupational environment measurement systems have limitations in accurately assessing and evaluating these varied conditions. This study aims to propose alternative measurement and assessment strategies to supplement existing methods. Methods: Major domestic coal-fired power plants were selected as the study targets. To prepare for the study and establish strategies, work processes were identified and existing occupational environment measurement results were compared and analyzed. The study proceeded by employing three strategies: specific exposure groups (SEGs) measurement, continuous monitoring, and supplementary measurements, which were then compared and discussed. Results: Previous exposure index evaluations (5,268 cases) indicated that crystalline silica, a type of respirable particulate matter, had detection limits below the threshold (non-detectable) in 82.6% (4,349 cases) of instances. Exposures below 10% of the exposure limit were observed at a very low concentration of 96.1%. Similar exposure group measurements yielded results where detection limits were below the threshold in 38.2% of cases, and exposures below 10% of the limit were observed in 70.6%. Continuous monitoring indicated detection limits below the threshold in 12.6% of cases, and exposures below 10% of the limit were observed in 75.6%. Instances requiring active workplace management accounted for more than 30% of cases, with SEGs at 11.8% (four cases), showing a higher proportion compared to 3.0% (four cases) in continuous monitoring. For coal dust, exposures below 10% of the limit were highest in legal measurements at 90.2% (113 cases), followed by 74.0% (91 cases) in continuous monitoring, and 47.0% (16 cases) in SEGs. Instances exceeding 30% were most prevalent in SEGs at 14.7% (five cases), followed by legal measurements at 5.0% (eight cases), and continuous monitoring at 2.4% (three cases). When examining exposure levels through arithmetic means, crystalline silica was found to be 104.7% higher in SEGs at 0.0088 mg/m³ compared to 0.0043 mg/m³ in continuous monitoring. Coal dust measurements were highest in SEGs at 0.1247 mg/m³, followed by 0.1224 mg/m³ in legal measurements, and 0.0935 mg/m³ in continuous monitoring. Conclusions: Strategies involving SEGs measurement and continuous monitoring can enhance measurement reliability in environments with irregular work processes and frequent fluctuations in working conditions, as observed in coal-fired power plants. These strategies reduce the likelihood of omitting or underestimating processes and enhance measurement accuracy. In particular, a significant reduction in detection limits below the threshold for crystalline silica was observed. Supplementary measurements can identify worker exposure characteristics, uncover potential risks in blind spots of management, and provide a complementary method for legal measurements.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.249-252
• /
• 2004

The automatic determination of vehicle operation status as well as continuous tracking of vehicle location with intelligent management is one of major elements to achieve the goals. Especially, vehicle operation status can only be analyzed in terms of expert experiences with real-time location data with scheduling information. However the scheduling information of individual vehicle is very difficult to be interpreted immediately because there are hundreds of thousand vehicles are run at the same time in the national wide range workplace. In this paper, we propose the location-based knowledge management system(LKMs) using the active trajectory analysis method with routing and scheduling information to cope with the problems. This system uses an inference technology with dispatching and geographic information to generate the logistics knowledge that can be furnished to the manager in the central vehicle monitoring and controlling center.

• Journal of Power System Engineering
• /
• v.20 no.3
• /
• pp.64-73
• /
• 2016

In this research work, an algorithm development on tracking end-point of aerial work platform with jib profile and bend-linked boom was carried out to find the X, Y and Z direction value using coordinate transformation matrix. This matrix consists of device status value(length and angle) based on camera position axis, which are sent from device controller PLUS+1 by CAN protocol. These values are used to measure the distance and angle from the camera to the end-point. Using these distance and angle value, monitoring system controls FAN/TILT/ZOOM status of camera to get an adequate scene of workplace. This program was written in Java, C# and C for mobile device. These results provide the information to the aerial work device for secure operation.

• Safety and Health at Work
• /
• v.3 no.3
• /
• pp.192-198
• /
• 2012

Objectives: Slip and fall accidents in the workplace are one of the top causes of work related fatalities and injuries. Previous studies have indicated that fall risk was related to postural and dynamic stability. However, the usage of this theoretical relationship was limited by laboratory based measuring instruments. The current study proposed a new method for stability assessment by use of inertial measurement units (IMUs). Methods: Accelerations at different body parts were recorded by the IMUs. Postural and local dynamic stability was assessed from these measures and compared with that computed from the traditional method. Results: The results demonstrated: 1) significant differences between fall prone and healthy groups in IMU assessed dynamic stability; and 2) better power of discrimination with multi stability index assessed by IMUs. Conclusion: The findings can be utilized in the design of a portable screening or monitoring tool for fall risk assessment in various industrial settings.