• 센서학회지
• /
• 제19권1호
• /
• pp.36-42
• /
• 2010

This paper describes a multi channel measurement system which can measure the cellular respiration level in a solution containing cells by using a Clark-type sensor with the solution temperature control unit. The Clark-type sensor can measure the cellular respiration level in the solution because it can measure the reduction current depending on the dissolved oxygen level in the solution. This measurement system was maintained the temperature within ${\pm}0.1^{\circ}C$ of the setting temperature value by on/off control method in order to measure the precise cellular respiration level. The measurement system showed that the applied voltage to the working electrode was very stable(-0.8 V$\pm$ 0.0071 V) by using proportional control method. From the current measurement, the response time and the linearity correlation coefficient were 25 sec and 0.94, respectively, which are very close to the results of the commercial product. Using this system and the fabricated Clarktype sensor, the average ratio of the uncoupled OCR(oxygen consumption rate) to the coupled OCR was 1.35 and this is almost the same as that obtained from a commercial systems.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.308-308
• /
• 2013

본 연구에 염료감응형 태양전지(Dye Sensitized Solar Cells; DSSCs)의 광전변환효율을 높이기 위해 작업전극에 새로운 구조의 광투과층 및 산란층을 도입하였다. DSSCs 작업전극의 빛을 투과시키는 투과층에 크기가 10 nm 이하의 nanoparticle $TiO_2$를 적용하고, 투과된 빛이 산란되어 많은 전자가 여기 될 수 있도록 기존의 큰 입자 사이즈였던 산란층을 이용하는 대신 $TiO_2$ nanorod 및 nanotube 형태의 구조를 도입하여 기존의 작업전극과 비교하였다. 산란층에서 방향성을 가지는 rutile 상의 $TiO_2$는 저온에서 안정적인 anatase 상의 $TiO_2$보다 화학적으로 안정하며, 높은 산란율을 가지고, 광에 의해 여기된 전자를 직접적으로 집전전극에 전달해 줌으로서 소자의 효율을 증가시킨다고 보고되고 있다. Rutile 상의 $TiO_2$ 층 제작 시 수열합성법을 이용하면 nanorod 모양의 $TiO_2$층을 형성할 수 있고, 이와 같은 방법으로 성장시킨 산란층에 전기영동법의 식각 효과를 사용하면 nanotube 모양의 $TiO_2$층을 성장시킬 수 있어 산란효과의 극대화 및 전극의 표면적을 넓히는 장점이 있다. 각각의 방법을 이용하여 만든 구조 위에 입자 크기 10 nm의 $TiO_2$를 Dr blade 방법으로 도포하여 double layer (산란층+흡수층)로 구성된 작업 전극을 이용한 DSSCs를 제작한 후 I-V curve와 EIS (Electrochemical Impedance Spectroscopy)를 측정하여 효율 및 전기화학적 특성을 분석하였다.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.365-379
• /
• 1994

Pool boiling experiments were carried out to study the effect of electric field on nucleate boiling heat transfer. CFC-11 and its alternative HCFC-123 were used as working fluids. Boiling on both single tube and a bundle of five tubes was investigated. Heat flux varied from 5 to $25kW/m^2$ while the applied voltage changed from 0 to 1kV. The results showed that at low heat flux where boiling was not present or very weak, electric field-induced forced convection helped increase the heat transfer coefficients of CFC-11 and HCFC-123 significantly(4-15 times increase). However, at higher heat flux, nucleate boiling of CFC-11 which is a highly dielectric fluid, was not affected significantly by the application of electric field. In contrast to CFC-11, even at high heat flux, nucleate boiling of CFC-11 which has a relatively larger electric conductivity than CFC-11, was vigorously increased up to 2-4 times. The additional power required to apply the electric field was 1-2% of the total power consumption by the heater. The increase in overall heat transfer coefficient of evaporators with HCFC -123 was about 40%, suggesting a considerable reduction in evaporator size with EHD technique.

• 한국분말재료학회지
• /
• 제17권3호
• /
• pp.216-222
• /
• 2010

Self-standing $TiO_2$ nanotube arrays were fabricated by potentiostatic anodic oxidation method using pure Ti foil as a working electrode and ethylene glycol solution as electrolytes with small addition of $NH_4F$ and $H_2O$. The influences of anodization temperature and time on the morphology and formation of $TiO_2$ nanotube arrays were investigated. The fabricated $TiO_2$ nanotube arrays were applied as a photoelectrode to dye-sensitized solar cells. Regardless of anodizing temperature and time, the average diameter and wall thickness of $TiO_2$ nanotube show a similar value, whereas the thickness show a different trend with reaction temperature. The thickness of $TiO_2$ nanotube arrays anodized at $20^{\circ}C$ and $30^{\circ}C$ was time-dependent, but on the other hand its at $10^{\circ}C$ are independent of anodization time. The conversion efficiency is low, which is due to a morphology breaking of the $TiO_2$ nanotube arrays in manufacturing process of photoelectrode.

• 대한조선학회논문집
• /
• 제39권3호
• /
• pp.81-88
• /
• 2002

용접구조물의 루트부는 외력에 의한 응력 집중에 의해 파손되기 쉽다. 따라서 구조물의 안전성 및 신뢰성 측면에서 홈 가공한 그루브 용접에 의한 완전용입 용접이 일반적으로 요구되어진다. 하지만 필릿 T-이음부 용접은 루트부의 갭과 같은 불완전 용입부를 만들어내기 쉬움에도 불구하고 홈 가공 시간 및 용접봉 소모량을 줄이기 위해 이러한 필릿용접이 자주 행해지고 있다. 따라서, 본 연구에서는 필릿 용접구조물의 플래이트(또는 플랜지)와 웨브 부분에 발생하는 용접잔류 응력과, 특히 불완전 용입에 의한 루트부 갭을 갖는 양면 T-이음부의 노치부분에 발생하는 잔류응력 분포를 해석하고자 하였다. 해석을 위해서 서브머지드 아-크 용접에 의한 단층 및 다층패스용접 모델을 선정하였으며, 열전도 및 열탄소성 이론을 고려한 유한요소 프로그램을 사용하였다.

• 마이크로전자및패키징학회지
• /
• 제24권2호
• /
• pp.37-41
• /
• 2017

$Cu_2O$는 초저가 태양전지의 흡수층으로 적용될 수 있는 물질 중 하나로 direct band gap($E_g={\sim}2.1eV$)을 갖고 있으며 최대 650 nm 파장의 빛을 흡수 할 수 있는 높은 흡수율을 가지고 있다. 또한 무독성, 풍부한 매장량으로 낮은 비용 등의 여러 장점을 가지며 간단하고 저렴한 방법으로 대량으로 제작이 가능하다. 본 연구에서 Au가 증착된 $SiO_2/Si$ 기판 위에 전착법을 통해 $Cu_2O$ 박막을 제작하였다. 우리는 용액의 pH와 작업전극에 인가되는 전위, 용액의 온도와 같은 공정조건을 바꾸어주었고 최종적으로 XRD와 SEM 사진 분석을 통해 박막의 특성을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.380-381
• /
• 2007

This paper reports on the deposition conditions and properties of ITO films used as electrode layer in a organic light emitting diodes on a PET substrate. The deposition technique employed was specially designed roll-to-roll sputtering. The oxide was deposited at room temperature in an argon and oxygen plasma on a transparent conducting ITO layer on a PET film. The influence of deposition parameters such as DC power, working pressure and oxygen partial pressure has been investigated, in order to obtain the best compromise between a high deposition rate and adequate electro-optical properties. Electrical and optical properties of ITO films were analyzed by Hall measurement examinations with van der pauw geometry at room temperature and UV/Vis spectrometer analysis, respectively. In addition, the structural properties and surface smoothness were measured by x-ray diffraction and scaning electron microscopy, respectively. From optimized ITO films grown by roll-to-roll sputter system, good electrical$(6.44{\times}10^{-4}\;{\Omega}-cm)$ and optical(above 86 % at 550 nm) properties were obtained. Also, the ITO films exhibited amorphous structure and very flat surface beacause of low deposition temperature.

• 한국재료학회지
• /
• 제31권3호
• /
• pp.150-155
• /
• 2021

Zinc oxide (ZnO) based transparent conducting oxides (TCO) thin films, are used in many applications such as solar cells, flat panel displays, and LEDs due to their wide bandgap nature and excellent electrical properties. In the present work, fluorine and aluminium-doped ZnO targets are prepared and thin films are deposited on soda-lime glass substrate using a RF magnetron sputtering unit. The aluminium concentration is fixed at 2 wt%, and the fluorine concentration is adjusted between 0 to 2.0 wt% with five different concentrations, namely, Al2ZnO98(AZO), F0.5AZO97.5(FAZO1), F1AZO97(FAZO2), F1.5AZO96.5(FAZO3), and F2AZO96(FAZO4). Thin films are deposited with an RF power of 40 W and working pressure of 5 m Torr at 270 ℃. The morphological analysis performed for the thin film reveals that surface roughness decreases in FAZO1 and FAZO2 samples when doped with a small amount of fluorine. Further, optical and electrical properties measured for FAZO1 sample show average optical transmissions of over 89 % in the visible region and 82.5 % in the infrared region, followed by low resistivity and sheet resistance of 3.59 × 10-4 Ωcm and 5.52 Ω/sq, respectively. In future, these thin films with excellent optoelectronic properties can be used for thin-film solar cell and other optoelectronics applications.

• 한국환경과학회:학술대회논문집
• /
• 한국환경과학회 2019년도 정기학술대회 발표논문집
• /
• pp.83-83
• /
• 2019

Increasing the CO₂ concentration in the atmosphere induce high temperature and rising sea levels. So the technology that capture and reuse of the CO₂ have been recently become popular. Among other methods, CRR(CO2₂ reduction reaction) is typical method of CO₂ reusing. Electrocatalyst can show more higher efficiencies in CRR than photocatalyst because it doesn't use nature source. Nowadays, finding high efficient electrocatalyst by controlling electronic (affected by stoichiometry) and geometric (affected by atomic arrangement) factors are very important issues. Mono-atomic electro-catalyst has limitations on controlling binding energy because each intermediate has own binding energy range. So the Multi-metallic electro-catalyst is important to stabilize intermediate at the same time. Carbon monoxide(CO) which is our target product and important feedstock of useful products. Au is known for the most high CO production metal. With copper, Not only gold/copper has advantages which is they have FCC packing for easily forming solid solution regardless of stoichiometry but also presence of adsorbed CO on Cu promotes the desorption of CO on Au because of strong repulsion. And gold/copper bi-metal catalyst can show high catalytic activity(mass activity) although it has low selectivity relatively Gold. Actually, multi-metallic catalyst structure control method is limited in the solution method which is takes a lot of time. In here, we introduce CTS(carbo thermal shock) method which is using heat to make MMNP in a few seconds for making gold-copper system. This method is very simple and efficient in terms of time(very short reaction time and using carbon substrate as a direct working electrode) and increasing reaction sites(highly dispersed and mixing alloy structures). Last one is easy to control degree of mixing and it can induce 5 or more metals in one alloy system. Gold/copper by CTS can show higher catalytic activity depending on metal ratio which is altered easily by changing simple variables. The ultimate goals are making CO₂ test system by CTS which can check the selectivity depending on metal types in a very short time.

• 분석과학
• /
• 제21권2호
• /
• pp.129-134
• /
• 2008

순환전압전류법과 벗김전압 전류법을 사용한 폭발물(hexahydro-1,3,5-trinitro-1,3,5-triazine, RDX)의 흔적량 분석을 위하여 double-stranded ds calf thymus (DNA)와 카본 나노튜브 혼합 전극을 사용하였으며. 최적 분석 조건을 시험한 결과 0.2 V vs. Ag/AgCl 전위에서 봉우리 전류를 발견하였다, 이 전위를 사용하여 선형분석 농도 범위: 50-75 ug/의 순환전압전류법과, 5-80 ng/L의 벗김 전압 전류법에 도달하였으며, 10 ug/L의 농도에서15번 반복 측정한 상대 표준편차는 0.086% 이었다. 또한 300초의 벗김 분석 조건에서 0.65 ng/L ($2.92{\times}10^{-12}M$) (S/N=3)의 검출 한계에 도달 하였으며, 이 조건에서 폭약에 오염된 토양중의 RDX 흔적량을 분석 응용하였다.