• Journal of the Korea Furniture Society
• /
• v.25 no.3
• /
• pp.207-212
• /
• 2014

With increased interests in environmental issues, people are looking for new materials that serve special and bio-activated functions. One of interesting materials is charcoal which has excellent adsorption ability for harmful volatile organic compounds, fireproof performance, far-infrared ray emission, and electromagnetic shielding. Since non-crack carbonized board was developed from wood-based composite materials, carbonization method might be applied to woodcraft products such as wood cup and bamboo. In this study, manufacture of wood charcoal bowl was conducted with carbonization method developed in 2009 in order to activate wood products market. Ash tree(Fraxinus rhynchophylla) cup was carbonized at $600^{\circ}C$ with two pretreatments which were phenol resin and wood tar solution treatment. After carbonization of ash tree cup, non-crack charcoal cup were successfully manufactured. Phenol resin treatment affected on charcoal cup manufacturing both positively and negatively. For a positive way, it prevented shrinkage. For a negative way, it decreased water repellency. On the contrary, wood tar treatment accelerated shrinkage a bit and increased water repellency. Based on the results, wood tar can be used as pre-treatment solution for reducing post-treatment costs. We confirmed woodcraft products can be carbonized without deformation, so carbonization may provide a high value-added products from wood.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.1
• /
• pp.55-68
• /
• 1989

This experiment was carried out to investigate the crack of coated Nitrocellulose Lacquer on flatand edge-grained boards of Quercus acutissima, ring-porous wood, and Betula platyphylla var. japonica, diffuse-porous wood, by variations of moisture contents at 7, 13 and 21%. Cold check system was used as an accelerating method for crack development, in which one cycle of the system consisted of 10 replications of each unit cycle, $60^{\circ}C$ for 4hr followdd by $-20^{\circ}C$ for 4hr. The analysis of Nitrocellulose Lacquer characteristics was made by means of water permeation measurement, F.T.I.R. spectroscopy, N.M.R. spectroscopy, gel permeation chromatography, gas chromatography, and D.S.C. The results obtained were as follows: 1. The number of cracks increased with the increasing moisture content of board. 2. The crack of coated film on flat-grained board was fewer in number than on edge-grained board. 3. The crack occurred in Quercus acutissima was more numerous on edge-grained board but less frequent on flat-grained board compared with that in Betula platyphylla var. japonica, respectively. 4. The cold crack vertically developed to the grain both in Quercus acutissima and Betula platyphylla var. japonica. 5. Water permeability in intermediate coated film was lower than in under and top coated film, but the difference was not confirmed between under and top coated film.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.15-22
• /
• 1993

This study was carried out to investigate the fracture criterion of glulam. The mixed mode fracture of glulam was investigated by means of single edge notched specimens with various crack inclination in the longitudinal-radial plane. While fracture of wood is not completely understood, the study on linear-elastic fracture mechanics is a rational and valuable tool for studying the strength behavior of glulam. The results are summarized as follows : 1. Glue line has no effect on fracture strength. 2. There is a definite interaction between fracture toughness $K_I$ and $K_{II}$ during the mixed mode fracture of glulam. Several criterions for mixed mode failure were compared. The criterion was expressed in the following form: $(\frac{K_I}{K_{IC}})^2+(\frac{K_{II}}{K_{IIC}})^2=1$ 3. As crack inclination increases, $K_{IC}$ value and $K_{IIC}$ value decreases. The equations relating crack angle to $K_{IC}$ and $K_{IIC}$, respectively, were obtained as follows; $K_{IC}$ = -77.42${\gamma}$+153.72 ($R^2$ = 0.78) $K_{IIC}$ = -9.17${\gamma}$+34.90 ($R^2$ = 0.48)

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.11a
• /
• pp.123-126
• /
• 2006

Existing Deck Plate for a one of system forms, there is various advantage and application actual results increasing rapidly. But design of deck is depending on engineering data collections or design data on deck manufacture ordinarily. When construct, is responsible for deflection occurrence, And Because confirmation of crack occurrence region is impossible, there is difficulty of repair, reinforcement about crack and water leakage. According to got following conclusion as result that economic performance, preservation administration and repair reinforcement develops easy using steel truss snap tie by wedge pin on coating plywood that is slab Panel Wood System Form method of construction there is Deck Plate's advantage. (1) In stab lower part is exposed disjointing in which a criminal is fastened to be interrogated after construction acceptance and repair, reinforcement of crack is possible (2) Construction cost curtailment effect of about 29.2% than conventional type and about 10% than deck plate (3) Construction period reduction of about 3 day than conventional type and about 0.3 day than deck plate (4) Labor curtailment effect more than about $29{\sim}50%$ from conventional type

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.5
• /
• pp.343-351
• /
• 2012

A large diameter roundwood is an important element of Korean traditional buildings, Hanok, and is hard to be dried without surface cracks. Four different pretreatments, such as pre-cracking, oil heating, kerfing-oil heating and PEG impregnation, were investigated for reducing the surface cracks of large-diameter roundwood specimens during heat treatment. The roundwood specimens of pre-cracking, oil heating and kerfing-oil heating showed surface cracks during pretreatment, but that of PEG impregnation did not. It was confirmed that kerfing reduced the total crack width. Among the four pretreatments and control only the PEG impregnation roundwood specimen had no crack on both outer and inner surfaces after heat treatment. The PEG impregnation specimen shrank only 1.6% in the tangential direction while the pre-cracking did 8.0%.

• Journal of Korea Multimedia Society
• /
• v.19 no.8
• /
• pp.1275-1280
• /
• 2016

This research is for the visualization of wooden cracking phenomena in the virtual world. Timber supplies has been traditionally used for buildings in the all over the world. Wood has a characteristic that is more prone to be influenced and distorted under the external environments compared with other materials like as stone and concrete. Many related researches say that moisture content change is a largest impact factor for the distortion and crack of timber supplies. This is the reason why we focus on the relationship between the moisture variations and the wood distortion, especially crack. In this research, it is mathematically explained that the diminutions of tensile strength caused by repeated contraction and expansion according to the moisture variations under the changes of weather. Finally, we suggest a way to visualize it for pine timbers.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.10a
• /
• pp.124-128
• /
• 1991

Wood, laminates, reinforced concrete, and some special types of metals systems with controlled grain orientation are often orthotropic and at least rectilinearly anisotropic from point to point, if regarded as homogeneous media. Orthotropic bodies where a crack is not associated with a plane of elastic symmetry may be conveniently treated as a crack problem in a generally anisotropic body. At this work, approach for the determination of the stress intensity factors (SIF) of anisotropic body using crack tip singular elements is presented. Caculated values are in good agreement with the others.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2021.07a
• /
• pp.645-647
• /
• 2021

본 논문에서는 목조건물의 Crack만을 움직여 Data set을 증강하는 기법을 제안한다. 이 기법은 이미지 내 Crack Detection의 학습 데이터를 만들기 위해 이미지의 전체적인 값으로 Flip, Rotation, Shift, Rescale 등의 변환을 통해 Data Augmentation을 진행하는 대신 Crack이라는 하나의 Object만을 가지고 새로운 데이터를 생성한다. 이때 Object는 관심 영역 내에서만 연산되어 기존의 방법보다 더욱 많은 데이터를 얻을 수 있으며, Crack이 관심 영역 밖으로 이동하지 않기 때문에 이상치 혹은 결측치가 존재하지 않는 데이터를 얻을 수 있다. 또한 Crack이 존재하지 않는 이미지에도 임의적으로 Crack을 생성하여 새로운 데이터를 만들 수 있다. 결론적으로 본 논문에서는 Crack Detection의 학습을 위하여 기존 방법보다 우수한 성능의 Data Augmentation을 제안하였다.

• Journal of the Korean Institute of Rural Architecture
• /
• v.21 no.1
• /
• pp.37-44
• /
• 2019

Recently, various tourist products using hanok have increased rapidly. In the meantime, there is a steady demand for Hanok architecture. However, there are many negative perceptions about wood deformation and biodeterioration. Wood deformation and biodeterioration are related to moisture content. And the cracks occur in the process of removing water from the wood. Therefore, this study investigates the moisture content and cracks of dried hanok made of wood according to the drying method of wood. Drying methods include natural seasoning and artificial seasoning. There was a difference in moisture removal depending on drying period and method of natural seasoning. Drying time should be about 3 years for natural seasoning, so the moisture content of the wood is stable. In addition, the moisture absorption rate was low even in a humid environment where the voids were removed. However, natural seasoning is time consuming. Artificial seasoning, on the other hand, can quickly remove moisture from the wood and reduce porosity, but it is costly. Cracks that occur during the drying of wood may become problematic in appearance and stability due to wider spacing over time. As a result, the difference in the moisture content of the timber depending on the drying method and drying period of the wood was maintained even after the formation. These gaps appeared to be differences in moisture absorption in a wet environment.

• Journal of the Korea Furniture Society
• /
• v.24 no.3
• /
• pp.302-308
• /
• 2013

To collection of field data for development of maintenance manual of Han-ok, we investigated defects which occurred in members of Han-ok by field investigation. The noticeable defects were wood cracks, gaps that developed between wood pillar and wall or wood window frame and tenon joints. The most common biological defect was blue stain which was created in log. The mold generation was observed on exterior wood and wall which get wet by precipitation. The gaps between members of Han-ok pointed out as defect that is urgently improved by residents of Han-ok. The reason is mainly due to poor of insulation in winter by bad confidentiality. The maintenance work of defect such as gap was conducted personally. As a result, the repair parts were ugly for unfamiliar repair work.