• 설비공학논문집
• /
• 제13권11호
• /
• pp.1049-1058
• /
• 2001

The performance and design analysis for a NWD cooling tower using a combined wet and dry type fill are numerically investigated and compared with the experimental results. The Stoecker's method is applied to the wet section and LMTD or NTU-Effectiveness method to the wet and dry sections. The efficiency ratio of the NWD cooling tower to a wet type crossflow cooling tower is 59.34%. The predicted result shows a good agreement with the experimental data within 1.4% error. Plume abatement is far better with a NWD cooling tower than a counterflow cooling tower. It costs less than a conventional wet/dry tower because the finned exchanger is eliminated. This method also leaves out complexity in structure and Intricacy in operation.

• 한국세라믹학회지
• /
• 제31권1호
• /
• pp.55-61
• /
• 1994

Mn-Zn ferrite powder was obtained by wet method that was to be coprecipitated the metal ions of Fe2+, Mn2+ and Zn2+ with alkali solution. The target composition of the ferrite powder was 52 mol% Fe2O3, 24 mol% MnO, and 24 mol% ZnO, that was based on the region of high permeability. And the other ferrite powder was prepared by the dry method that was to be mixed the metal oxides as the above chemical composition. The wet method was compared with dry method for the powder properties and the electromagnetic characteristics of sintered cores. The synthesized powder by wet method was smaller particle size, narrower particle distribution, and higher purity than that of dry method. The initial permeability of sintered sample prepared by the wet method was 14000~28000, on the other side, 9000~15500 in case of the dry method.

• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.158-162
• /
• 2001

In this report, a new process for patterning of YBaCuO thin films, ICP(inductively coupled plasma) method, is described by comparing with existing wet etching method. Two 100㎛ wide and 2mm long YBaCuO striplines on LaAlO$_3$ substrates have been fabricated using two patterning techniques. And the properties were compared with the critical temperature and the SEM photography. Then, the critical temperatures of two samples were about 88 K, but the cross section of sample using ICP method was shaper than that using the wet etching method. ICP method can be used as a good etching technique process for patterning of YBaCuO superconductor.

• 한국세라믹학회지
• /
• 제16권3호
• /
• pp.155-163
• /
• 1979

This study was to explore the characteristics of 6 mole% CaO stabilized $ZrO_2$ prepared by wet chemical methods. The results of the experiments were as follows: 1. The powder calcined at 1000$^{\circ}$-110$0^{\circ}C$ was partly agglomerated. The morphology of agglomerate was spherical of 0.5-1$\mu{m}$ in size for Hot Petroleum Drying Method, chain-like of 1-2$\mu{m}$ for Freeze Drying Method, and irreqular of 2-3$\mu{m}$ for Coprecipitation Method. 2. Optimum calcining conditions for powder prepared by wet chemical methods were found: 110$0^{\circ}C$, 2h in air for Hot Petroleum Drying Method and Freeze Drying Method, and 100$0^{\circ}C$, 2h in air for Coprecipitation Method. 3. When specimen was calcined at 1000$^{\circ}$-110$0^{\circ}C$ in air for 2h and then sintered at 1$600^{\circ}C$ in air for 4h, the specimens prepared by wet chemical methods showed a high sintered density (94% of theoretical density) and a low open porosity (<0.8%); however, the sintered density of the specimen prepared by Oxide Wet Mixing Method was 90%. 4. The amount of cubic phase of sintered body prepared by wet chemical methods was observed to be higher than the one prepared by Oxide Wet Mixing Method. 5. It was found that Hot petroleum Drying Method, Freeze Drying Method and Coprecipitation Method were nearly the same in respect of the results of stabilization grade and sintered density of CaO-stabilized $ZrO_2$.

• 한국안광학회지
• /
• 제13권4호
• /
• pp.59-63
• /
• 2008

목적: 본 연구의 목적은 수분제거 방법과 건조 방법에 따른 함수율 측정에 관하여 알아보고자 하였다. 방법: 다양한 함수율을 갖는(47%~58%) 72개의 하이드로젤 콘택트렌즈를 대상으로 중량측정법으로 함수율을 측정하였다. 실험실 온도는 $25^{\circ}C$, 습도는 21%로 유지하였다. 두 방법 모두 저온처리 후 실온에서 30분 건조하여 무게를 측정하는 방식으로 측정하였다. 결과: Dry blotting 방법은 함수율이 47.43${\pm}$8.48%로 측정되었으며, Wet blotting 방법은 48.15 ${\pm}$8.36%로 측정되었다. 또한 Wet blotting 방법으로 측정한 함수율이 약 0.7% 정도 높게 측정되었다. 건조 방법에 따른 함수율에서 vacuum oven을 사용하여 건조한 함수율이 47.89${\pm}$8.06%, microwave oven을 사용하여 건조하여 측정한 함수율이 49.56${\pm}$7.06%로 나타났으며, microwave oven을 사용하여 측정한 함수율이 약 1.67% 높은 함수율을 나타내었으나 통계적으로 유의한 차이를 나타내지는 않았다(p>0.05). 결론: 렌즈의 함수된 무게를 측정하기 위한 Dry blotting 방법과 Wet blotting 방법 중 Wet blotting에 의한 방법이 무게가 높게 측정되었으며, 함수율 역시 더 높게 측정되었다. 또한 건조된 무게를 측정하기 위해 렌즈를 건조시키는 방법에 있어 vacuum oven을 사용한 건조보다 microwave oven로 건조하여서 측정한 함수율이 더 높은 값을 나타내었으나 microwave oven을 사용할 경우 더 정확한 측정을 위해 그 microwave의 조사 강도나 시료의 위치에 있어 더욱 세심한 주의가 필요하다.

• Bulletin of the Korean Chemical Society
• /
• 제35권11호
• /
• pp.3280-3288
• /
• 2014

Alkoxyalcohols are used as solvents or preservatives in various consumer products such as wet wipes. The metabolites of alkoxyalcohols are known to be chronically toxic and carcinogenic to animals. Thus, an analytical method is needed to monitor alkoxyalcohols in wet wipes. The aim of this study was to develop a simultaneous analytical method for 14 alkoxyalcohols using headspace gas chromatography coupled with mass spectrometry to analyze the wet wipes. This method was developed by comparing with various headspace extraction parameters. The linear calibration curves were obtained for the method ($r^2$ > 0.995). The limit of detection of alkoxyalcohols ranged from 2 to $200ng\;mL^{-1}$. The precision of the determinative method was less than 18.20% coefficient of variation both intra and inter days. The accuracy of the method ranged from 82.86% to 119.83%. (2-Methoxymethylethoxy)propanol, 2-phenoxyethanol, and 1-phenoxy-2-propanol were mainly detected in wet wipes.

• 한국토양비료학회지
• /
• 제31권3호
• /
• pp.253-258
• /
• 1998

마이크로파 시료 분해법이 식물체와 퇴비 중의 K, Ca, Mg, Cu, Zn, Mn등을 분석하는데 적합한가를 검정하기 위하여 기존의 습식분해법과 비교하였다. 분석시간은 기존의 습식분해법이 4~6시간 걸리던 것에 비하여 마이크로파 분해법에서는 1시간 이하로 단축할 수 있었으며, 두 분석법간의 각 성분별 분석값의 상관계수($R^2$)는 각각 K 0.98, Ca 0.97, Mg 0.91, Zn 0.94, Mn 0.99, Cu 0.99를 나타내었다. 칼륨과 칼슘의 경우 기존 습식분해법의 분석값이 더 높은 경향을 나타내었고 구리, 망간, 아연의 경우는 마이크로파 분해법의 분석값이 더 높은 경향을 나타내었으나 마그네슘의 경우 일정한 경향이 없었다. 그러나 칼슘의 경우를 제외한 그 외 성분들의 편기도(biases)는 10% 이내였다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2004년도 학술발표회
• /
• pp.1331-1334
• /
• 2004

Wet/Dry phenomena typically incorporate a number of complex flow mechanism. These include a momentum transfer and turbulent mixing caused by the delivery of water. However currently available one dimensional schemes applicable to wet/dry process cannot effectively simulate such process. Two dimensional finite element model, SU/PG, is used to simulate complex flow in this study. The Wetted Area Method in SU/PG allows elements to transition gradually between wet and dry states. The model is applicable to a straight river reach with irregular bathymetry. Wet/dry calculation using the wetted area method can simulate simple numerical test. The computed results of velocity vectors and water depth agree with those of observed. The methodology Presented in this study will contributed to two-dimensional wet/dry analysis in a river in this country.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.624-628
• /
• 2008

Two-dimensional flow analysis is a way to provide good estimates for complex flow features in flow around islands and obstructions, flow at confluence and flow in braided channel. One of difficult problems to develop a two-dimensional hydraulic model is to analyze dry and wet area in river channel. Dry/wet problem can be encountered in river and coastal engineering problems, such as flood propagation, dam break analysis, tidal processes and so on. The objective of this study is to develop an accurate and robust two-dimensional finite element method with dry/wet technique in complex natural rivers. The dry/wet technique with Deforming Grid Method was developed in this study. The Deforming Grid Method was used to construct new mesh by eliminating of dry nodes and elements. The eliminated nodes and elements were decided by considering of the rising/descending velocity of water surface elevation. Several numerical simulations were carried out to examine the performance of the Deforming Grid Method for the purpose of validation and verification of the model in rectangular and trapezoidal channel with partly dry side. The application results of the model were displayed reasonable flow distribution.

• 한국축산식품학회지
• /
• 제39권1호
• /
• pp.54-64
• /
• 2019

Wet and dry aging methods were applied to improve the quality of three different beef cuts (butt, rump, and sirloin) from Hanwoo cows (quality grade 2, approximately 50-mon-old). After 28 d of wet aging (vacuum packaged; temperature, $2{\pm}1^{\circ}C$) and dry aging (air velocity, 2-7 m/s; temperature, $1{\pm}1^{\circ}C$; humidity, $85{\pm}10%$), proximate composition, cooking loss, water holding capacity, shear force, color, nucleotides content, and sensory properties were compared with a non-aged control (2 d postmortem). Both wet and dry aging significantly increased the water holding capacity of the butt cuts. Dry aging in all beef cuts induced lower cooking loss than that in wet-aged cuts. Shear force of all beef cuts was decreased after both wet and dry aging and CIE $L^*$, $a^*$, and $b^*$ color values in butt and sirloin cuts were higher in both wet and dry aging (p<0.05) groups than those in the non-aged control. Regardless of the aging method used, inosine-5'-monophosphate content among beef cuts was the same. The sensory panel scored significantly higher values in tenderness, flavor, and overall acceptability for dry-aged beef regardless of the beef cuts tested compared to non- and wet-aged cuts. In addition, dry-aged beef resulted in similar overall acceptability among the different beef cuts, whereas that in wet-aged meat was significantly different by different beef cuts. In conclusion, both wet and dry aging improved the quality of different beef cuts; however, dry aging was more suitable for improving the quality of less preferred beef cuts.