• 한국정보통신학회논문지
• /
• 제5권1호
• /
• pp.133-143
• /
• 2001

본 논문은 직각파 및 뇌충격진류에 대한 봉상접지각의 과도임피던스 특성을 정상접지지항과 비교.분석하였다. 접지계는 단일$(\Psi10[mm], 1[m])$과 5[m]의 간격을 두고 서로 연접한 3연접 봉상접지극으로 구성하였으며, 과도 임피던스 특성을 분석하기 위하여 상승시간 30[ns], 펄스폭 $20[\mus]$의 직각파전류 발생장치를 설계 제작하였다. 실제 낙뢰에 의한 접지임피던스의 변화를 관찰하기 위하여, 국제규격 ANSI/IEEE, IEC에 규정되어 있는 뇌충격전류를 인가하여 이에 따른 특성변화를 측정.분석하였다. 접지계로 유입된 과도전류는 접지계의 전위를 상승시키며, 이 때의 전위상승과 유입전류의 비로써 접지임피던스를 산출하며, 뇌격전류에 대한 경제적인 보호 수준을 평가.예측하기 위하여 임피던스 파라미터를 측정결과로부터 산출하였다. 또한 연접에 따른 접지임피던스의 감소와 접지리드선이 미치는 영향도 분석하였다.

• 한국전자파학회논문지
• /
• 제21권2호
• /
• pp.170-178
• /
• 2010

논문에서는 전원부에서 노이즈가 발생되어 신호선에 노이즈가 유기될 때, 유전체의 손실 특성이 노이즈에 미치는 영향에 관해서 연구를 하였다. 이를 분석하기 위해 Full-wave 시뮬레이터인 Ansoft사의 HFSS(High Frequency Structure Simulation)와 CST사의 MWS(MicroWave Studio)의 계산 결과와 측정 결과를 비교하여 신뢰성을 확보하였고, 실제 사용되고 있는 4가지의 상용 기판에 대한 유기되는 노이즈를 해석하였다. 또한, TLM(Transmission Line Method)를 이용해서 전원면의 회로 모델 구성 시 기판의 유전체 손실을 반영할 수 있는 Debye 모델을 적용하여 주파수에 대한 임피던스를 분석할 수 있는 모델을 적용 측정 결과와 3 GHz까지 일치하는 모델을 얻었다.

• 대한전자공학회논문지SD
• /
• 제40권8호
• /
• pp.580-587
• /
• 2003

본 논문에서는 진행파형 전계흡수 변조기 (TW-EAM: traveling-wave electroabsorption modulator)의 선형성을 분석하기 위한 새로운 모델을 제시한다. TW-EAM은 소자의 길이, 마이크로파 손실 (microwave loss, ML), 그리고 임피던스 부정합에 의한 내부반사(internal reflection, IR) 등이 소자의 선형성에 영향을 미친다. 소자의 길이의 증가는 혼변조 왜곡 (intermodulation distortion, IMD)이 최소가 되는 전원전압의 크기를 감소시킨다. ML의 증가는 3차 혼변조 왜곡 (third-order IMD, IMD3)의 감소와 동시에 출력신호의 전력도 감소시킨다. IR은 입력주파수의 파장과 소자의 길이에 따라 각기 다른 IMD 특성을 나타낸다. ML 또는 IR에 의한 SFDR (spurious-free dynamic-range)의 변화는 거의 없었으며, TW-EAM의 IR을 이용하면 ML에 의한 신호 전력의 감쇄를 보상해 줄 수 있음도 알 수 있었다. 결과적으로 50 GHz 대역의 RF-광통신용 TW-EAM은 길이가 0.8 mm이고 출력단의 임피던스 부정합을 이용하면서 최소의 손실을 가지는 구조가 적당함을 알 수 있었다.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3272-3282
• /
• 2022

To improve the safety and life extension qualities of nuclear fuel rods which is currently made of zirconium (Zr) alloy, research on the application of chromium (Cr) coating was conducted. Cr coating has advantages such as increased corrosion resistance and reduced oxidation rate, but non-destructive thickness evaluation studies are needed to ensure the reliability of the steps taken to provide uniform coating thickness. Eddy current testing (ECT) is a representative non-destructive technique for such as thickness evaluation and surface defect inspection. To inspect changes in thickness at micron scale, the Swept Frequency Eddy Current Testing (SFECT) method was applied to select a frequency range sensitive to changes in thickness. The coating thickness was evaluated using changes in signals, such as that for impedance. In this study, basic research was performed to evaluate the thickness of the Cr coating on a rod using an encircling sensor and the SFECT technique. The sensor design parameters were determined through simulation, after which the new sensor was manufactured. A sensor capable of measuring the thickness of a non-uniformly Cr-coating rod was selected through an experiment evaluating the performance of the manufactured sensor. This was done using the impedance-difference of a Cr-coating rod and a Zr alloy rod. The possibility of evaluation of the Cr coating thickness was confirmed by comparing the experimental results with the selected sensor and the signals of the measured Cr-coating rod. All simulation results were verified experimentally.

• 한국지진공학회논문집
• /
• 제19권6호
• /
• pp.257-263
• /
• 2015

Recently two seismic cloaking methods of earthquake engineering have been suggested. One is the seismic wave deflection method that makes the seismic wave bend away and the other is the shadow zone method that makes an area that seismic waves cannot pass through. It is called as seismic cloaking. The fundamental principles of the seismic cloaking by variable refractive index were explained. A two-dimensional cylindrical model which was composed of 40 layers of different density and modulus was tested by numerical simulation. The center region of the model to be protected is called 'cloaked area' and the outer region of it to deflect the incoming wave is called 'cloaking area' or 'cloak area.' As the incoming surface wave is approaching to the cloaking area, the refractive index is decreasing and, therefore, the velocity and impedance are increasing. Then, the wave bends away the cloaked area instead of passing it. Three cases are tested depending on the comparison between the seismic wavelength and the diameter of the cloaked region. The advantage and disadvantage of the method were compared with conventional earthquake engineering method. Some practical requirements for realization in fields were discussed.

• Journal of the Korean Wood Science and Technology
• /
• 제17권2호
• /
• pp.26-33
• /
• 1989

The acoustic absorption coefficient and acoustic impedance of 5 species of softwood(sonamoo, sam namoo, gusang namoo, hwaback, sitka spruce) and 5 species of hardwood (Mulgusul namoo, Italian popular, white meranti, red meranti, kalantas) were measured by the standing wave method. which is simple in the setup and gives more accurate result than does any other measuring method. The dependence of the absorption coefficient and complex acoustic impedance on the wood sections. thickness of the sample itself and the back air gap was investigated experimentally in the frequency range from 200Hz to 1800Hz, and the result are as follows: 1. The acoustic absorption coefficient of wood sections was higher on the cross section than radial and tangential sections. 2) The acoustic absorption coefficient were higher in the frequency range from 400Hz to 600Hz, but decreased in the frequency above 600Hz. 3. The genenal tendency of the variation of the normal acoustic impedance was increased according to the frequency. 4. The acoustic absortion coefficient was increased in the to 7mm-thick sample and decreased in 9mm-thick sample. 5. The higher acoustic absorption coefficient was shown in the case with the backing an gap than in the case without the gap.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권3호
• /
• pp.35-39
• /
• 2013

In this paper, we present test results of developed 100 W class linear compressor for Stirling-type pulse tube refrigerator. The fabricated linear compressor has dual-opposed configuration, free piston and moving magnet type linear motor. Power transfer, efficiency and required pressure waveform are predicted with designed and measured specifications. In experiments, room temperature test with flow impedance is conducted to evaluate performance of developed linear compressor. Flow impedance is loaded to compressor with metering valve for flow resistance, inertance tube for flow inertance and buffer volumes for flow compliance. Several operating parameters such as input voltage, current, piston displacement and pressure wave are measured for various operating frequency and fixed input current level. Behaviors of dynamics and performance of linear compressor as varying flow impedance are discussed with measured experimental results. The developed linear compressor shows 124 W of input power, 86 % of motor efficiency and 60 % of compressor efficiency at its resonant operating condition.

• 한국통신학회논문지
• /
• 제30권12A호
• /
• pp.1136-1146
• /
• 2005

본 논문에서는 전력선 통신을 위해 사용되는 고압 배전선로에서 통신신호 및 잡음신호에 의해 방사되는 방사전계강도를 계산하였다. 전력선 통신 네트워크의 2포트 등가모델 및 기본적인 전송선로 이론을 이용해 입력임피던스를 계산하였다. 그리고 계산된 입력임피던스를 이용해 전력선상 전류를 계산하고 최종적으로 방사전계강도를 계산하였다. 전력선의 특성임피던스가 매우커서 입력 단에서의 반사가 심하기 때문에 입력임피던스는 일정한 주기를 가지는 정재파 형태를 가진다. 계산된 전류 및 방사전계 또한 이러한 형태임을 알 수 있었다. 실제 측정한 결과계산 치와 측정치가 매우 유사함을 알 수 있었다.

• 한국음향학회지
• /
• 제25권1호
• /
• pp.1-6
• /
• 2006

천해에서의 수중음장 계산에서 음향 임피던스를 해저면 입력인자로서 도입하는 방안의 가능성을 고찰하였다. 먼저 탄성 해저면에서의 음파반사 특성을 고찰한 결과, 임계 접지각 이하에서 음향 임피던스는 접지각이 거의 $0^{\circ}$에 가까울 때의 임피던스 $Z_0$ 1개 값으로 근사가 가능함을 나타내었다. 이러한 특성과 'effective depth' 개념을 접목시켜 전달손실을 계산한 결과, 수중음장 계산에서 임피던스를 해저면 음향 특성을 나타내는 입력인자로 사용하는 것이 가능성이 있음을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권3호
• /
• pp.18-27
• /
• 1996

The feasibility of using stress-wave technique in the transverse direction for the assessment of early stages of decay was investigated using compression test specimens having different annual ring orientations subjected to decay by Tyromyces palustris for various time intervals. Decay detection, quantitative assessment of decay, and the prediction of residual strength of decayed wood with less than five percent weight loss can be feasible using stress-wave parameters (wave velocity, wave impedance, and stress-wave elasticity) and their percent reduction due to decay, measured by stress-wave technique in the transverse direction. The use of stress-wave technique in the transverse direction for the application of this technique to structural members in service is desirable, when considering the easiness of attachment of accelerometers of stress-wave measuring device on the surface of members and also accurate detection of localized decayed areas. In stress-wave technique in the transverse direction, stress-wave parameters measured were different according to the angles between wave propagation path and annual ring, due to the anisotropy of wood structure. Therefore, it is recommended to use percent reduction in stress-wave parameters instead of stress-wave parameters. This evaluation method using percent reduction in stress-wave parameters is ideal when it is impossible to observe annual ring orientation on the transverse surface of wood.