• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3463-3473
• /
• 1996

The characteristics of wave propagation along a catenary depend on various impedance conditions; i.e., spatial impedance of catenary, impedance of boundaries. In this study, wave propagation along a simple catenary system is studied with arbitrary impedance conditions such as impedance of pantograph, boundary, catenary etc. Seven coupled equations which determine the characteristics of wave propagation along catenary system have been derived and numerically solved. Results demonstrate the role of each impedance condition in the dynamics of catenary system, i.e. the way in which the conditions affect waves on catenary as well as contact force of pantograph. The formulation and suggested solution method can be certainly used for desinging an optimal catenary system for a given pantograph.

• 전기의세계
• /
• 제14권1호
• /
• pp.26-34
• /
• 1965

The radiation patterns and impedance of the half wave solt on the wide side of rectangular wave guide are analyzed. The measuring methods and procedures are described. And that the experimental data of the pattern and impedance of the slot are presented which are consistent with the theoretical values. The causes of error are also considered and are believed to be tolerable for the pattern and input impedance measurements. The usefulness of the slot antenna tested are also described.

• Journal of the Korean Wood Science and Technology
• /
• 제25권1호
• /
• pp.8-14
• /
• 1997

Stress wave velocity, wave impedance, and stress wave elasticity of small, clear bending specimens of five domestic softwoods (Pinus densiflora, Pinus koraiensis, Chamaecyparis obtusa, Cryptomeria japonica, and Larix leptolepis) and four tropical hardwoods(Kempas, Malas, Taun, and Terminalia) were correlated with static bending modulus of elasticity(MOE) and modulus of rupture(MOR). The degree of correlation between stress wave parameters and static bending properties was dependent on wood species tested. Stress wave elasticity and wave impedance were better predictors for static bending properties than stress wave velocity for each species individually and for softwood or hardwood species taken as a group, even though elasticity and impedance were nearly equally correlated with static bending properties apparently. Based upon the correlation coefficient between stress wave parameters and static properties, stress wave elasticity and wave impedance were found as stress wave parameters which can be used for the purpose of the reliable and successful prediction of bending properties. The degree of correlation between static MOE and MOR was also different according to wood species tested. Static MOE was nearly as well correlated with MOR as was stress wave elasticity. The results of this research are encouraging and can be considered as a basis for further work using full-size lumber. From the results of this study, it was concluded that stress wave measurements could provide useful predictions of static bending properties and was a feasible method for machine stress grading of domestic softwoods and tropical hardwoods tested in this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.325-329
• /
• 2003

In this paper. the stability and performance analysis of wave-based teleoperation system is presented. For stability and performance analysis with respect to the variation of characteristic impedance b, loop gains of communication channel and minimum value of trasmitted impedance from slave side to the master side are considered. The stability of slave side may be enhanced by increasing characteristic impedance b, whereas exssively high value of b may degrade the performance, which imply a tradeoff between stability and performance.

• 한국전자파학회논문지
• /
• 제15권4호
• /
• pp.345-352
• /
• 2004

본 논문은 페라이트 필름을 기반으로 하는 마이크로스트립 선로로부터 여기되는 정자표면파의 복사 임피던스를 full-wave모멘트 해석법을 이용하여 계산하였다. 마이크로스트립 선로 폭과 페라이트 필름 두께 변화에 따른 여 기 특성 변화도 분석하였다. 정자파 근사에 의하여 계산된 복사 저항값은 주파수가 증가할수록 실험 값과 차이가 심해지나, full-wave 해석에 의하여 계산된 복사 저항값은 실험값에 매우 근접함을 알 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.423-430
• /
• 2002

A feasibility of a trial test method was evaluated analytically, in which the elastic modulus of a soil deposit was tried to estimate by analyzing dynamic signals measured during conducting the SPT. If there existed a reliable relationship between the impedance ratio of a rod to a soil and the amplitude ratio of a reflected to an incident wave signal at the tip of steel rod contacting the soil surface, it was expected that one could determine the impedance of soil, and then roughly estimate the elastic modulus from the impedance. For a simple rod-soil system, the existence of the relevant relationship was verified in this study by analyzing computed wave signals propagating up and down through the rod. On the basis of these results, thus, a potential of the test method to practical applications could be seen. However, apparent theoretical shortcomings possessed in this approach were also realized since the soil part had an unconfined contact area where contacted with the rod. Therefore, it was concluded that further studies needed to be conducted, in which the reliable theoretical relationship between the impedance and the amplitude ratio as well as the effective contacting soil area contributing to wave reflection should be justified.

• 한국전기전자재료학회논문지
• /
• 제26권6호
• /
• pp.472-477
• /
• 2013

This paper carried out the comparative analysis on ground impedance of a carbon block and a copper rod. Two types of grounding electrode were compared ; a carbon block (L : 1 m, ${\Phi}$ : 245 mm) buried at a depth of 0.8 m and a three-linked copper rod (L : 1 m, ${\Phi}$ : 10 mm) of equilateral triangles with 1 m spacing. Ground impedance depending on applied current source was evaluated by the application of a sine wave current with 60 Hz ~ 3.5 MHz, a fast-rise pulse with rising time of 200 ns, a standard lightning impulse of $8/20{\mu}s$ and a 600 Hz square wave. Ground impedance for both electrodes were almost the same value below 100 kHz, and increased rapidly afterwards. The maximum ground impedance appeared $400{\Omega}$ at around 1.5 MHz. Ground impedance of the carbon block was lower at the square wave and was higher at fast-rise pulse than that of the copper rod. Also, ground impedance as ages showed no difference for the last 8 months. From the results, it is likely that ground performance for both electrodes shows no difference against commercial frequency and lightning impulse current, while the copper rod shows better performance against a fast-rise pulse with rise-time of a few hundred ns.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2059-2071
• /
• 1992

본 연구에서는 물리적 상황을 구체적으로 표현하기 위하여 카테너리를 연속적 인 임피던스를 갖는 동력학계로 모델링하고 팬터그래프를 1자유도를 갖는 진동계로 간 주하여 카테너리의 시간 공간적 운동 및 카테너리에 작용하는 압상력의 변화를 예측하 고자 한다.

• The Journal of the Acoustical Society of Korea
• /
• 제26권2E호
• /
• pp.50-55
• /
• 2007

SBN (Structure-Borne Noise) reduction in resiliently mounted machineries are predicted by using mass-spring model and wave model. In mass-spring model, mount is modeled as a spring, while in wave model, mount is considered as an equivalent elastic rod for taking account into longitudinal wave propagation. The predictions for SBN reduction through mounts are compared to the measurements for four different pumps. It is found that the mass-spring model is valid only in low frequency range below few hundred Hz, while for high frequency ranges longitudinal wave propagation in the mount must be considered to explain the measurements. It is also shown that impedance of the floor slightly affects low frequency behaviour in mass-spring and wave model below 50 Hz - 80 Hz, so that in engineering practice the effect of floor impedance may be neglected in computing mount performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.86.6-86
• /
• 2002

This work presents a study on development of a practical and quantitative technique for assessment of the healthy state of a structure by piezoelectric impedance-based technique associated with longitudinal wave propagation measuring method. A truss structure embedded with piezoelectric patches is investigated for a fundamental study on estimation of the looseness of bolts in the joint. In order to evaluate the minute mechanical impedance change due to loosening bolt, a harmonic longitudinal elastic wave is applied to the structure by a pair of PZT patches and their electric impedance is measured simultaneously. According to the experimental results, the change of the electric impedance of P...