• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 A
• /
• pp.371-373
• /
• 2005

An enhancement for a transmission and substation equipment in power system make the system impedance to be lower. In principle, if the system impedance become low, system stability will be better, but the fault current become very higher. It is a very big problem for CB operating. As a fact of CB operating performance, high amplitude of the fault current may cause CB operation failure because of exceeding standard value in TRV. So we simulated TRV by using the EMTP. Generally there are two types of TRV in actual power system. One is short line fault, the other is bus terminal fault. In this paper, we simulated the TRv at short line fault as installed current limit reactors to reduce fault current in 345kV ultra-high voltage system. Short line fault is caused from single line fault in transmission line.

• Journal of Power Electronics
• /
• 제18권2호
• /
• pp.588-603
• /
• 2018

This paper presents the idea of a smart load that can adjust the input power flow based on the intermittent power available from RESs (Renewable Energy Resources) to regulate the line voltage, and draw a constant power from the grid. To this effect, an innovative power flow controller is presented based on a Resistive ES (Electric Spring) in combination with a PEAT (Power Electronics based Adjustable Transformer), which can effectively shape the load power flow at the subnetwork level. With a PEAT incorporated in the step down transformer at the grid side, the proposed controller can supply non-critical loads through local RESs, and the critical loads can draw a relatively constant power from the grid. If there is an abundance of power produced by the RESs, the controller can supply both non-critical loads and critical loads through the RES, which significantly reduces the power demand from the grid. The principle, practicality, stability analysis, and controller design are presented. In addition, simulation results show that the power flow controller performs well in shaping the load power flow at the subnetwork level, which decreases the power demand on the grid. Experimental results are also provided to show that the controller can be realized.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.220-224
• /
• 2009

The effect of addition of single and binary additives on the performance of dye-sensitized $TiO_2$ solar cells based on 1,2-dimethyl-3-propylimidazolium iodide (DMPII) in ethylene carbonate (EC) and gamma-butyrolactone (GBL) has been evaluated at different cell temperatures in the $30-120^{\circ}C$ range. The electrolyte containing a single additive, 2-(dimethylamino)-pyridine (DMAP) showed best performance, which showed further enhancement for an electrolyte containing binary additives, DMAP and 5-chloro-1-ethyl-2-methylimidazole (CEMI) in equal molar ratio. The performance of the dye sensitized solar cell (DSC) based on electrolyte containing binary additives were found to be better than an acetonitrile based electrolyte. The dependence of different photovoltaic parameters (Voc, Jsc, ff, n) of the DSC upon temperature has been studied over the $30-120^{\circ}C$ range and only a small decrease in conversion efficiency has been observed. Thus the electrolyte containing binary additives (DMAP, CEMI) in EC/GBL solvent and show better performance in the investigated temperature range ($30-120^{\circ}C$).

• Journal of the Optical Society of Korea
• /
• 제18권6호
• /
• pp.753-761
• /
• 2014

We propose a two-step UV irradiation procedure to fabricate polymer-dispersed liquid crystal (PDLC) films by lamination. During the first UV treatment, before lamination, the UV-curable monomers coated on one film substrate are solidified through photo-polymerization as the phase separation between the liquid crystals and the monomers. Introducing an adhesion-enhancement layer on the other plastic substrate and controlling the UV irradiation conditions ensure that UV-induced cross-linkable functional groups remain on the surfaces of the photo-polymerized layers. Thereby, the adhesion stability between the top and bottom films is much improved during a second (post-lamination) UV treatment by further UV-induced cross-linking at the interface. Because the adhesion-enhancement and PDLC layers prepared by the bar-coating process are solidified before lamination, the PDLC droplet distribution and the cell gap between the two plastic substrates remain uniform under the lamination pressure. This ensures that the voltage-controlled light transmittance is uniform across the entire sample.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.708-713
• /
• 1994

A new flux observer based vector control system of an induction motor is constructed by using an observer in which the commanded stator currents are used to estimate the rotor flux. In this system, the flux observer is formulated by using a model of induction motor in a stationary coordinate system. By considering an observer of induction motor in a fixed co-ordinate system located on its secondary flux, a slip frequency controlled type of vector control system is also proposed. From these control schemes, the relation between the conventional slip frequency controlled type system and the observer based one is clarified. The steady-state error of the developed torque which is caused by the parameter change of induction motor is analyzed and discussed for the selection of observer gains. The poles of the observer error dynamics and those of the observer based vector control system are calculated analytically by neglecting the machine parameter change. In order to analyze the robust stability, a linear model of the observer based vector control system is proposed taking into account the machine parameter change. By using this model, the trajectories of the poles and zeros of the torque transfer function are computed and discussed. To test validity of the theoretical analysis, experiments are conducted by using a digital signal processor (TMS320C30) and a current controlled voltage source PWM inverter.

• 대한전자공학회논문지SD
• /
• 제44권8호
• /
• pp.1-7
• /
• 2007

고주파 응용을 위한 AB급 바이폴라 선형 트랜스컨덕터들을 제안한다. 이들 트랜스컨덕터는 전압 폴로워, 저항기, 그리고 전류 폴로워로 구성된다. 폴로워 회로들은 트랜스리니어 셀들로 실현되기도 하고, 단위-이득 버퍼들로 실현되기도 한다. 제안된 트랜스컨덕터들은 8 GHz 바이폴라 트랜지스터-어레이 파라미터를 이용하여 SPICE 시뮬레이션 되었다. 시뮬레이션 결과는, 트랜스리니어 셀들을 이용한 트랜스컨덕터가 단위-이득 버퍼들을 이용한 그것보다 더 좋은 선형성을 가지는데 반해, 후자는 전자보다 더 좋은 온도 특성과 더 높은 입력 저항을 가진다는 것을 보여준다. 제안된 트랜스컨덕터들의 실용성을 검증하기 위하여, 이들 트랜스컨덕터로 중간 주파수(IF) 대역의 4차 대역-통과 여파기를 구현하였다.

• 대한임베디드공학회논문지
• /
• 제8권3호
• /
• pp.129-136
• /
• 2013

In this paper, a motion control system based on 2-axis gimbal system is designed and implemented to drive a high speed and precision. The proposed system consists of the RS-422 interface, 2-axis gimbal platform, servo control unit integrated with a high speed DSP chip-set, servo amplifier unit, potentiometer sensor unit, and resolver sensor unit. The servo control unit using the high speed DSP firmware is designed to get a fast response without an overshoot with step input and a RMS error of low probability with ramp input. The servo amplifier unit using a voltage control is designed to resolve the zero-crossing distortion for precise motion. To verify the performance and stability of the implemented system, experiments are performed through a measurement of the time and frequency domain response in a laboratory environment by using a PXI(PCI eXtentions for Instrumentation).

• 한국초전도ㆍ저온공학회논문지
• /
• 제7권4호
• /
• pp.28-31
• /
• 2005

To verify the feasibility of bifilar winding type superconducting fault current limiter (SFCL) using BSCCO tape, two types of magnets were fabricated and tested by short-circuit in this research. Even if the FCL using high Tc superconducting (HTS) tape has zero resistance in normal state, it needs to be wound as a bifilar winding for zero inductance. Solenoid type and pancake type bifilar winding magnets are designed and fabricated with the same length of BSCCO tape. The test system consists of AC power supply, transformer, fault switch, load and bifilar winding magnet. The applied AC voltages during fault duration, 0.1s, were from 0.5V to 20V. The test results without bifilar winding magnet were compared with those with each type magnets. The test results include voltage against magnet, transport current and generated resistance curve. Thermal stability, the recovery time, was studied from the results of two type magnets. The pancake type was the most effective to limit fault current but the solenoid type was thermally the most stable. From this research, short-circuit characteristics of the two types were obtained.

• 한국전자통신학회논문지
• /
• 제10권3호
• /
• pp.357-364
• /
• 2015

본 연구에서는 아날로그 메모리를 이용한 DC-DC 컨버터 제어기를 설계하였다. 이 방식은 기존의 폐루프 방식의 컨버터 제어기가 안고 있는 안정도 문제를 근본적으로 해결하는데 기여하게 될 것이다. 본 연구에서 아날로그 메모리는 컨버터의 출력과 이에 대응되는 최적의 시비율 판단을 위한 연상메모리를 구현하는데 이용된다. 메모리의 읽기 동작은 연상메모리의 최적 함수 선택을 위하여 절대값 회로와 승자전취 메커니즘 회로가 사용되며, 병렬의 고속 쓰기와 읽기 동작뿐만 아니라 고집적을 가능하게 하는 시스템 구성이 제안된다.

• 전기화학회지
• /
• 제12권3호
• /
• pp.245-250
• /
• 2009

Crosslinked membrane based on sulfonated polyimide was prepared by the introduction of crosslinkable monomer in polymerization process and crosslinking during membrane casting. Crosslinked membranes showed different properties from non-crosslinked membranes. Crosslinking decreased methanol crossover and therefore unit cell using crosslinked membrane showed increased open circuit voltage, 0.81 V, in comparison with unit cell using noncrosslinked membrane, 0.71 V. In addition, water uptake of crosslinked membrane, 40.5%, was lower than that of non-crosslinked membrane, 57.0%, and this resulted in improved dimensional stability. However, proton conductivity of crosslinked membranes showed rather low relative to non-crosslinked membrane due to reduced water uptake.