• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.65-67
• /
• 2002

The gas metal arc welding(GMAW) is regarded as one of the best candidate for welding automation in industrial joining application. It is important to monitor the weld quality for the high performance of weld automation. The measured analog signal is frequency analyzed by digital signal process method. In order to observe the welding phenomena and control welding condition, arc light, voltage, and current are measured at the same time. They are analyzed and compared with arc sound. for these experiments, a power source of constant voltage characteristics was used in the pure metal transfer mode.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1267-1269
• /
• 2000

New switching signal pattern for four switches is proposed to prevent the shortage of PWM ac choppers. In the proposed technique, four signals to four power switches are generated without current transformer, while the conventional technique requires sensing the polarity of input voltage by voltage comparator and checking the direction of input current by the current transformer. The signal circuit built by the proposed technique is simple, and reduces also the switching loss.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.7
• /
• pp.110-116
• /
• 1994

In this paper a Duty Effective Overlap Scanning method (DEOS) for the improvement of driving efficiency of LC displays which have the RMS voltage responding characteristics is proposed and new processing method of data signals for optimum application of this method is also proposed. Proposed method has a few advantages such as the increment of duty ratio the increment of driving power loaded on LC cell and the decrement of RMS voltage error rate caused by signal attenuation on electrodes composing of display when compared with the conventional method which is called as optimum voltage amplitude selection method. And also by adopting new data signal processing method which has 3 kinds of voltage levels additional advantage much improving crosstalk phenomenon which is the most serious problems of simple matrix structured display is obtained. For the characteristic estimation new mathematical representation for new overlap scanning method and data signal processing method are induced and defined. And by the defined formula and simulation the characteristics of the proposed method and the conventional method are compared and analyzed. As a result of estimation this new method being able to optimize the overlap rate of scan signal and using 3 levels of data signals has the characteristic which can improve the driving efficiency of LC displays.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.4
• /
• pp.281-285
• /
• 2018

An isolated feedback method for measuring the inverter DC-link voltage is proposed. This method provides a simple and economical solution to inverter control systems that use a flyback converter as a controller power supply. In the proposed method, data on the DC-link voltage are acquired when the primary side voltage appears on the secondary side of the flyback transformer, thereby eliminating the need to adopt an extra signal isolation method. To solve the non-synchronization problem between the flyback converter switching and main controller sampling, the external interrupt function of the micro-controller is used as a trigger signal for the A/D conversion.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.706-711
• /
• 2014

A low power 6-bit flash ADC that uses an input voltage range detection algorithm is described. An input voltage level detector circuit has been designed to overcome the disadvantages of the flash ADC which consume most of the dynamic power dissipation due to comparators array. In this work, four digital input voltage range detectors are employed and each input voltage range detector generates the specific clock signal only if the input voltage falls between two adjacent reference voltages applied to the detector. The specific clock signal generated by the detector is applied to turn the corresponding latched comparators on and the rest of the comparators off. This ADC consumes 68.82 mW with a single power supply of 1.2V and achieves 4.3 effective number of bits for input frequency up to 1 MHz at 500 MS/s. Therefore it results in 4.6 pJ/step of Figure of Merit (FoM). The chip is fabricated in 0.13-um CMOS process.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.975-981
• /
• 2020

A 10 GHz LC voltage-controlled oscillator (VCO), which controls an amplitude of output signal, is proposed to improve the phase noise. The proposed amplitude control circuit for the LC VCO consists of a peak detector, an amplifier, and a current source. The peak detector is performed detecting the lowest voltage of the output signal by using two diode-connected NMOSFET and a capacitor. The proposed 10 GHz LC VCO with an amplitude control circuit for output signal is designed using a 55 nm CMOS process with a supply voltage of 1.2 V. Its area is 0.0785 ㎟. The amplitude control circuit used in the proposed LC VCO reduces the amplitude variation 242 mV generated in the output signal of the conventional LC VCO to 47 mV. Furthermore, it improves the peak-to-peak time jitter from 8.71 ps to 931 fs.

• Journal of Semiconductor Engineering
• /
• v.1 no.2
• /
• pp.64-73
• /
• 2020

As CMOS technology scales down, the design of analog signal processing circuit becomes far more difficult because of steadily decreasing supply voltage and smaller intrinsic gain of transistors. With sub-1V supply voltage, the conventional analog signal processing relying on high-gain amplifiers is not an effective solution and different approach has to be sought. One of the promising approaches is "time-domain analog signal processing" which exploits the improving switching speed of transistors in a scaled CMOS technology. In this paper, various time-domain analog signal processing techniques are explained with some experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.581-584
• /
• 2000

Generally, it is known that many partial discharges are occurred in one voltage cycle. In this case, it is not easy to distinguish between ultrasonic signals caused by the partial discharge. We describes a pattern of the ultrasonic signal by the partial discharge in transformer. The test setup for ultrasonic signal measurement was to simulate a internal partial discharge by using a needle to plane electrodes. We compared the number of partial discharge and ultrasonic signal in one voltage cycle. The results showed that it was possible to distinguish between ultrasonic signals by analysing partial discharge detection method and ultrasonic signal on time domain.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.5
• /
• pp.24-29
• /
• 1976

In the phase locked AM signal detection, phase locked loop is used to extract a synchronous carrier from an input AM signal. Under the assumption that input noise is white Gaussian and free-running frequency of voltage controlled oscillator is the same that of an input carrier, operational behaviours of phase locked loop is analyzed and signal to noise ratio of the detection is derived quentitatively. The results show that the phase locked AM signal detection method offers a higher degree of noise mmunity than conventional AM signal detections.

• Journal of the Korean Society of Safety
• /
• v.29 no.2
• /
• pp.12-17
• /
• 2014

This paper is aimed to analyze the characteristics of simultaneous voltage, current and temperature signals for poor connection on electrical connector. In order to attain this purpose, detected were the current and voltage signals on electric wire with series arc, named arc signals, and also monitored were the changes of RMS, instantaneous value of waveform in time domain and temperature value with video. Two states are made normal state over $5kgf{\cdot}cm$ and poor connections state below $0.5kgf{\cdot}cm$ by screw gage. In the voltage signal case, the voltage drop was increased with which the current was increased. In the current signal case, poor connections at the time interval 1~4A all showed "shoulder", as distinct difference from the normal state shown waveform pattern. In the temperature signal case, poor connections are twice at 1A and five times at 4A in the normal state. The temperature continues insulation of electrical wiring and connector can be carbonized. The results of this study will be effectively used in developing the preventive devices and system for electric fire by poor connections.