• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.121-127
• /
• 2012

The study is to investigate the mixing stability, fuel properties, and macroscopic spray characteristics of diesel-gasoline blended fuels in a common-rail injection system of a diesel engine. The test fuels were mixed diesel with gasoline fuel, which were based volume fraction of gasoline from 0 to 100% in 20% intervals. In order to analyze the blended effect of gasoline to diesel fuel, the properties of test fuels such as density, viscosity, and surface tension were measured. In addition, the spray behavior characteristics were studied by investigating the spray tip penetration and spray angle using a spray images through a spray visualization system. It was revealed that the density, kinematic viscosity and surface tension of diesel-gasoline blending fuels were decreased with the increase of gasoline fuel. The injection quantity of test fuels were almost similar level at short energizing duration condition. On the other hand, the increase of energizing duration shows the decrease of injection quantity compared to short energizing duration. The test blending fuels have similar growth in Spray tip penetration and Spray cone angle.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.7
• /
• pp.35-42
• /
• 2016

There are many reclamation projects domestically and internationally which requires large quantity of reclaimable materials. To provide enough reclaimable soils which are limited in land, there have been various research focusing on the dredged soils in the marine environments. As a part of this research, a GIS based 3D dredging reclamation visualization program was developed for the volume estimation of dredged soils in 2015. The developed program is based on the digitized spatial information of the site investigation data with a consideration of the reliability of the data. Prior to the validation with the comparisons with the actual dredged volume measurement data, the developed program was compared with the commercial 3D visualization program with 3D visualized results from the test site near the Gunjang harbor. The validation of the developed program was performed in terms of the degree of visualized precision, the sectional and profiling of soil layers and the dredged volume estimation results. Based on the comparisons, both commercial and developed program show similar dredged volume with minor discrepancies in soil layers.

• Journal of Practical Engineering Education
• /
• v.12 no.1
• /
• pp.31-39
• /
• 2020

Big data analysis is analyzed and used in a variety of management and industrial sites, and plays an important role in management decision making. The job competency of big data analysis personnel engaged in management analysis work does not necessarily require the acquisition of microscopic IT skills, but requires a variety of experiences and humanities knowledge and analytical skills as a Data Scientist. However, big data education by state-run and state-run educational institutions and job education institutions based on the National Competency Standards (NCS) is proceeding in terms of software engineering, and this teaching methodology can have difficult and inefficient consequences for non-technical majors. Therefore, we analyzed the current Big Data platform and its related technologies and defined which of them are the requisite job competency requirements for field personnel. Based on this, the education courses for big data analysis and visualization techniques were organized for non-technical-based majors. This specialized curriculum was conducted by working-level officials of financial institutions engaged in management analysis at the management site and was able to achieve better educational effects The education methods presented in this study will effectively carry out big data tasks across industries and encourage visualization of big data analysis for non-technical professionals.

• Journal of Gifted/Talented Education
• /
• v.8 no.2
• /
• pp.69-89
• /
• 1998

The purpose of this study is to develop a test which can be used in identification of the gifted students in the area of mathematics. This study was carried out for two years from 1996. Mathematical giftedness is, in this study, regarded as a result of interaction of mathematical thinking ability, mathematical creativity, mathematical task committment, background knowledge. This study presumed that mathematical thinking ability is composed of seven thinking abilities: intuitive insights, ability for information organization, ability for visualization, ability for mathematical abstraction, inferential thinking ability(both inductive and deductive thinking abilities), generalization and application ability, and reflective thinking. This study also presupposed that mathematical creativity is composed of 3 characteristics: fluency, flexibility, originality. The test for mathematical creative problem solving ability was developed for primary, middle, and high school students. The test is composed of two parts: the first part is concentrated more on divergent thinking, while the second part is more on convergent thinking. The major targets of the test were the students whose achievement level in mathematics belong to top 15~20% in each school. The goodness of the test was examined in the aspects of reliability, validity, difficulty, and discrimination power. Cronbach $\alpha$ was in the range of .60~.75, suggesting that the test is fairly reliable. The validity of the test was examined through the correlation among the test results for mathematical creative problem solving ability, I. Q., and academic achievement scores in mathematics and through the correlation between the scores in the first part and the scores in the second part of the test for mathematical creative problem solving ability. The test was found to be very difficult for the subjects. However, the discrimination power of the test was at the acceptable level.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.278-285
• /
• 1991

The authors propose to use the slot system in order to improve of the efficiency for the cambered otter boards. The experiment is divided into 2 parts, one is the efficiency model test, and the other is the visualization model test. The hydrodynamic characteristics of the model otter boards were tested by efficiency model test to measure the shearing, drag force of the models and visualization test using hydrogen bubble method to observe the streak-line and time-line of flow around the models, and milk spout method to observe the separation zone in the wake behind the models. This study tested for 5 models such ad without slot, slot position 0.2C, 0.4C, 0.6C and 0.8C. The results obtained are as follows: \circled1 The maximum C sub(L) of model otter board with slot position 0.6C in attack angle 27$^{\circ}$ was the highest of all models, it's value was 1.59. \circled2 In general, the L/D ratio of the one slot otter boards were 16~28% higher than otter board without slot. \circled3 The slot position 0.6C was better than any other slot position, and it's conformed by visiualization. \circled4 As to the model otter board with slot position 0.6C, flow speed of the back side was faster 1.3 to 1.7 times than in the front side. \circled5 The size of the separated zone in case of the model otter board with 0.6C was smaller than that of any other models.

• Korea-Australia Rheology Journal
• /
• v.16 no.2
• /
• pp.63-73
• /
• 2004

Flow in a channel with an obstruction at the entry can be reverse, stagnant or forward depending on the position of the obstruction. These flow phenomena have potential applications in the control of energy and various flows in process engineering. Parameters that affect this flow inside and around the test channel are the gap (g) between the obstruction geometry and the test channel, the Reynolds number (Re) and the length (L) of the test channel. The influence of these parameters on the flow behavior was investigated using a flat plate obstruction at the entry of the channel. A low concentration polyacrylamide solution (0.018% by weight) showing a powerlaw fluid behavior was used as the fluid in this investigation. The flow phenomena were investigated by the velocity measurement and the flow visualization and their results were compared with numerical simulation. These results of low concentration polyacrylamide solution are also compared with the results of water published elsewhere (Kabir et al., 2003). The maximum reverse flow inside the test channel observed was 20% - 30% of the outside test channel velocity at a g/w (gap to width) ratio of 1 for Reynolds numbers of 1000 to 3500. The influence of the test channel length (L) and the Reynolds number (Re) on the velocity ratio ($V_i$/$V_o$: inside velocity/outside velocity in the test channel) are also presented and discussed here.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.717-722
• /
• 2010

Supersonic/Hypersonic wind tunnel is a facility which is intended to test and to observe the physical phenomena around a model by creating supersonic flow in the test section. In designing an airplane, the wind tunnel test is demanded to analyzing aerodynamic characteristics of the model without making a prototype. In this research, the model aerodynamic facility(MAF) is modified for the purpose of increasing running time and its functionality. New pneumatic valves for remote control was installed for safety requirement, and new air tanks was installed on MAF as well. A pipe system is also modified to use those new valves and tanks, and the ceiling and side glasses of the test section are switched to ones with the larger surface area. After the MAF modification, a test is performed at Mach 2, 3 and 4. In this test, shadow graph technique, one of the flow visualization methods, is used to visualize supersonic flow field. The pressure in the settling chamber and working section at Mach 2, 3 and 4 was measured in each case. As a result, the possible model size and running time are obtained.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.173-183
• /
• 2010

Numerical analysis using a three dimensional finite element program(ABAQUS) is a powerful method which can evaluate the soil-pile-structure interaction under the dynamic loading and reduce the computation time significantly, but has not be widely used because modeling a soil-pile system and setting the parameter for the entire model are difficult and a three dimensional finite element program is not user friendly. However, a three dimensional finite element program is expected to be widely used because of advance in research of modeling technique and development of the modeling and visualization. In this study, ABAQUS is used to simulate the 1g shaking table model pile test, and the numerical results are compared with the 1g shaking table test results. The application about the soil stiffness and boundary condition change is estimated and then parametric study for various input acceleration amplitudes, various input frequencies, and various surcharge is carried out.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.11-17
• /
• 2007

In this paper, we present a design, analysis, fabrication and performance test of the novel DoD metal-jet system for application to the high-density and high-temperature-melting materials. The theoretical analysis of the metal-jet nozzle system is derived by using electro-mechanical analogy. Based on the theoretical analysis results, we design the metal-jet print head system and fabricate the metal-jet system, which can eject the droplet of lead-free metal solder in high-temperature. In the experimental test, we set up the test apparatus for visualization of the droplet ejection and measure the ejected droplet volume and velocity. As a result, the diameter, volume and the velocity of the ejected droplet are about 65 $\mu$m $\sim$ 70 $\mu$m, 145p1 $\sim$ 180 pl and 4m/s, which shows quite good agreement with the theoretical analysis results of the 75 $\mu$m-diameter and 220 pl-volume of droplet. In comparison with the experimental result, the errors of diameter and volume are 7% $\sim$ 13% and 18 $\sim$ 34%, respectively.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.359-364
• /
• 2007

Spray characteristics of the APU gas turbine engine were investigated. In order to understand blow out phenomena of the APU engine, we performed fuel spray test. In the test, four operating conditions such as sea level idle, sea level max power, 20,000 feet idle, 20,000 feet max power were used as spray experimental conditions. PDPA(phase Doppler Particle Analyzer) was used for measuring the particle diameter and velocity. Also spray visualization was performed by using ND-YAG sheet laser beam. From the test result, in the case of 20,000 feet idle condition, SMD is about 100 ${\mu}m$ and maximum particle velocity is about 10 m/s. For the flame stability, spray quality should be improved at 20,000 feet idle condition.