• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3386-3394
• /
• 1994

An experimental study has been performed on the flow over a rotating disk, where the diameter of the disk is 500 mm and the maximum vertical deviation of the upper surface is $50 \mu{m}$ for the whole range of the angular velocity up to 3400 rpm. The flow visualization experiment for the wall jet flow induced by impinging circular jet is carried out using schlieren system and measurements are made by 3-hole and 5-hole pitot tubes. Schlieren photographs show that as the rotating speed increases the wall jet flow becomes more stable and the size of the largest eddies becomes smaller. Measurements for impinging jet flow on the stationary disk verify the accuracy of the present experiment, and those for free rotating disk flow display the existence of transition region from laminar to turbulent flows. Measurements for impinging jet flow on the rotating disk exhibit the interaction between the wall jet and the viscous pumping effect, which explains the decay in size of turbulent eddies illustrated by the schlieren photographs.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 추계 학술대회논문집
• /
• pp.167-174
• /
• 1998

The numerical methodology for simulating water entry behaviors of the high-speed bodies has been developed. Since the present method assumed the impact occurs within a very short time interval, the viscous effects do not have enough time to play a significant role in the impact forces, that is, the flow around a water-entry object was assumed as an incompressible potential flow and is solved by the source panel method. The elements fully submerged into the water are routinely teated, but the elements intersected by the effective planar free surface are redefined and reorganized to be amenable to the source panel method. To validate the present code, it has been applied to the ogive model and compared with experimental data. Good agreement has been obtained. The water entry behavior of the bouncing phenomena from the free surface has been also simulated using the impact forces and two degree of freedom dynamic equation. Physically, acceptable results have been obtained.

• 한국해양공학회지
• /
• 제6권1호
• /
• pp.29-42
• /
• 1992

자유표면하에 잠긴 복잡한 3차원 물체 주위의 흐름을 해소하기 위한 수치계산법이 TUMMAC(Tokyo Univ. Modified Marker And Cell)법을 기초로 하여 개발되었다. 임의물체의 no-slip 3차원 물체표면조건을 보다 간단히 처리하기 위하여 "porosity"라는 개념이 도입되었으며, 담수성에 잠겨 있는 해저돌출물 주위의 유동을 계산하여 그 응용성을 검토하였다. 돌출물 후방의 복잡한 와동들의 상호간섭이 잘 시뮬레이션 되었다.시뮬레이션 되었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 춘계 학술대회논문집
• /
• pp.43-48
• /
• 1998

The development of unsteady three-dimensional incompressible viscous solver based on unsteady physical curvilinear coordinate system is presented. A 12-point finite analytic scheme based on local uniform grid spacing is extended for nonuniform grid spacing. The formulation of a condition is suggested to avoid the oscillation of the series summations produced by the application of the method of separation of variables. SIMPLER and pressure Poisson equation techniques are used for solving a velocity-pressure coupled problem. The matrix is solved using the Generalized Minimal RESidual (GMRES) method to enhance the convergence rate of unsteady flow solver and the Kinematic boundary condition of a free surface flow. It is demonstrated that the numerical solutions of these equations are less mesh sensitive.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.25-40
• /
• 2015

Understanding the effects of the parameters affecting the interaction of tandem hydrofoil system is a crucial subject in order to fully comprehend the aero/hydrodynamics of any vehicle moving inside a fluid. This study covers a parametric study on tandem hydrofoil interaction in both potential and viscous fluids using iterative Boundary Element Method (BEM) and RANSE. BEM allows a quick estimation of the flow around bodies and may be used for practical purposes to assess the interaction inside the fluid. The produced results are verified by conformal mapping and Finite Volume Method (FVM). RANSE is used for viscous flow conditions to assess the effects of viscosity compared to the inviscid solutions proposed by BEM. Six different parameters are investigated and they are the effects of distance, thickness, angle of attack, chord length, aspect ratio and tapered wings. A generalized 2-D code is developed implementing the iterative procedure and is adapted to generate results. Effects of free surface and cavitation are ignored. It is believed that the present work will provide insight into the parametric interference between hydrofoils inside the fluid.

• 대한조선학회논문집
• /
• 제44권3호
• /
• pp.248-257
• /
• 2007

Turbulent flows around a sailing yacht hull were calculated using CFD technique. Grid system was generated by using Gridgen package and Fluent package was used to calculate flows around a 30ft-class yacht hull designed by MOERI. The drafts at starboard and port sides of a yacht. when the hull was heeled, were determined by adjusting the same displacement in the generated grid system. Pressure distribution on the sailing yacht hull was obtained and the changes of drag and side force by heel and leeway variation were shown. The flow calculations have been carried out both with and without free surface, and keel and rudder were included for both cases. It was found that the calculated results with free surface gives better agreement with experiments than those without free surface, although there are still a room for the improvement in correct prediction of forces.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.188-192
• /
• 2004

A Numerical analysis method is developed in order to compute the flaw and wave field for 2-dimensional floating body in the free roll motion with 3 degrees of freedom. Navier-Stokes and continuity equations are gaverning equations in tire present study. Finite Difference method is introduced to discretize the governing equation. The free surface is traced by the interface tracking method and the grid system is fitted to boundaries including free surface and body surface, which is moving in the flow field. The numerical scheme is based on Maker and Cell method. For the sake of validation of the numerical method, the computed roll decay factors according to tire midship section shapes are compared with measured results. The numerical results are discussed in order to understand the effect of midship section shape on roll motion.

• 한국항해항만학회지
• /
• 제28권8호
• /
• pp.753-757
• /
• 2004

선미파의 점성 상호작용과 수중고속선의 sub-breaking 현상을 해석하기 위하여 자유표면 유통을 수치적으로 시뮬레이션하였다. Navier-Stokes 방정식을 풀었으며 유한차분법, 물체적합좌표계, 벽법칙, 삼중격자법을 적용하였다. S-103 모형을 대상으로 준쇄파의 수치결과를 실험과 비교하였고 준쇄파 발생조건을 수중 고속선인 3차원 회전체에 대해 적용하였다. 준쇄파 해석결과에 의하면 M/Us 구배가 잠김 깊이에 영향을 미치고 있음을 알 수 있었다. 또한 선수파가 박리에 영향을 미쳐 선미파를 변형시킴을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.197-200
• /
• 2002

In this paper, roll damping coefficients for a non-conventional cross section, which is herein named as 'step' model, are investigated numerically and experimentally. Experiments are extensively carried out to estimate the roll damping coefficients. Numerical estimations are also made with the help of numerical codes. For convenience, the roll damping is divided into wave-making component and viscous component. The wave-making component is determined using a potential code and the viscous component using a viscous flow code, in which the fluid domain is taken as unbounded. In order to validate the present approach, a typical cross section with bilge is considered and our results are compared with published data. The comparison shows a good agreement qualitatively. For the step model, numerical results are compared well with experimental data besides some quantitative discrepancies at a certain range of frequency. It is thought that the discrepancy might be caused by the ignorance of the free surface in viscous computations. It is found in the case of the step model that not only the viscous component but also the wave component increases considerably compared to the section with bilge.

• 대한조선학회논문집
• /
• 제47권3호
• /
• pp.388-397
• /
• 2010

A two-dimensional time-domain, potential-theory-based fully nonlinear numerical wave tank (NWT) was developed by using boundary element method and the mixed Eulerian-Lagrangian (MEL) approach for free-surface node treatment. The NWT was applied to prediction of primary wave energy conversion efficiency of a bottom-mounted oscillating water column (OWC) wave power device. The nonlinear free-surface condition inside the chamber was specially devised to represent the pneumatic pressure due to airflow velocity and viscous energy loss at the chamber entrance due to wave column motion. The newly developed NWT technique was verified through comparison with given experimental results. The maximum energy extraction was estimated with various chamber-air duct volume ratios.