• 한국응용과학기술학회지
• /
• 제22권2호
• /
• pp.116-122
• /
• 2005

Room temperature cure type of acryl-urethane coatings with high solid content were prepared in this study. Acrylic resins with 80% solid content were cured with hexamethylene diisocyanate (Desmodure N-3600). The cure time of prepared coatings BEHCC-84 (BEHC-84 : $T_g=0^{\circ}C$) and BEHCC-87 (BEHC-87 : $T_g=30^{\circ}C$), measured by rigid-body pendulum method, was recorded 8.3 hours and 3.8 hours, respectively. Dynamic viscoelastic experiment also revealed the glass transition temperature of BEHCC-84 and BEHCC-87 to be $T_g=40.3^{\circ}C$ and $T_g=43.3^{\circ}C$, respectively. It was found that the adhesion and flexural properties among various propeties of coatings were enhanced by the incorporation of caprolactone acrylate monomer into the acrylic resins.

• 한국소음진동공학회논문집
• /
• 제16권7호
• /
• pp.690-696
• /
• 2006

Thickness of damping layer in sandwich plate needs to be optimized in order to make modal loss factor of the sandwich plate maximum. Since previous studies were interested in noise reductions over high frequency range, the modal properties were derived based on simply supported boundaries. This conventional formula is approximately applicable to other boundary conditions over high frequency range only. The purpose of this study is to propose a method to determine optimum damping layer thickness of sandwich plate for maximum modal damping in low frequency range when the boundary condition is not a simple support. The conventional RKU equation based on simply supported boundary is modified to reflect other boundary conditions and the modified RKU equation is subsequently applied to determine the optimum damping layer thickness for arbitrary conditions. In order to reflect frequency-dependent characteristics of elastic modulus of the damping layer, an iteration method is proposed in determining the modal properties. Test results on sandwich plates for optimum damping layer thickness are compared with predictions by the proposed method and conventional method.

• 한국염색가공학회지
• /
• 제15권2호
• /
• pp.59-67
• /
• 2003

PTT[poly(trimethylene terephthalate)] fiber was annealed by passing on the plate heater to illuminate the effects of annealing on the mechanical properties and dyeability with varying the treatment temperature for 0.5 second. The apparent crystal sizes and crystallinity were increased with increases in temperature. With the increases of the temperature, the dynamic viscoelastic behaviors were analyzed to be reduction in $T_{max} (tan{\delta})$. The initial modulus were observed to be a small enhanced. The shrinkage in hot water were reduced. The dyeability for disperse dye enhanced dramatically, for example, a satisfactory degree of exhaustion was obtained by dyeing at $95^\circ{C}$ for 30 min with the PTT fibers heat treated at $180^\circ{C}$.

• 한국정밀공학회지
• /
• 제10권1호
• /
• pp.134-141
• /
• 1993

Electro-Rheological(ER) fluids undergo a phase-change when subjected to an external electic field, and this phase-change typically manifests itself as a many-order-of-magnitude change in the rheological behavior. This phenomenon permits the global stiffness and energy- dissipation properties of the beam structures to be tuned in order to synthesize the desired vibration characteristics. This paper reports on a proof-of-concept experimental investigation focussed on evaluation the vibration properties of hollow cantilevered beams filled with an ER fluid. and consequently deriving an empirical model for predicting field-dependent vibration characteristics. A hydrous-based ER fluid consisting of corn starch and silicone oil is employed. The beams are considered to be uniform viscoelastic materials and modelled as a viscously-damped harmonic oscillator. Natural frequency, damping ratio and elastic modulus are evaluated with respect to the electric field and compared among three different beams: two types of different volume fraction of ER fluid and one type of different particle concentration of ER fluid by weight. Transient and forced vibration responses are examined in time domain to demonstrate the validity of the proposed empirical model and to evaluate the feasibility of using the ERfluid as an actuator in a closed-loop control system.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.62-70
• /
• 2005

The nanoindenter and AFM have been used for nanofabrication, such as nanolithography, nanowriting, and nanopatterning, as well as measurement of mechanical properties and surface topology. Nanoscale indents can be used as cells for molecular electronics and drug delivery, slots for integration into nanodevices, and defects for tailoring the structure and properties. Therefore, it is very important to make indents of desired morphology (shape, size and depth). Indents of different shapes can be obtained by using indenters of different geometries such as a cube comer and conical and spherical tips. The depth and size of indents can be controlled by making indentations at different indentation loads. However, in case of viscoplastic viscoelastic materials such as polymethylmethacrylate (PMMA) the time dependent deformation (TDD) should also be considered. In this study, the effect of process parameters such as loading rate and hold-time at peak load on the indent morphology (maximum penetration depth, elastic recovery, transient creep recovery, residual depth pile-up height) of PMMA were studied for hyperfine pattern fabrication.

• 한국화재소방학회논문지
• /
• 제22권5호
• /
• pp.61-66
• /
• 2008

본 연구에서는 특정물질의 과열로 인한 이상 상태를 조기에 감지하여 화재 및 폭발로의 전이 위험성을 사전에 예방할 수 있는 방법 중 하나로 열변색 색소를 유효성분으로 한 겔성형체를 제조하여 그 특성을 평가하였다. 또한 과열감지용 대상물에 대한 적용성을 확대하기 위하여 성형체는 원료물질의 종류와 함량, 그리고 제조방법에 따라 점탄성형과 도포형의 2가지로 제조하였다. 변색성 시험, 점도 특성, 변색 개시시간, FT-IR 분석을 수행한 결과 이상 조건을 효과적으로 감지하여 변색 기능을 나타낼 수 있는 물질이 제조되어 다양한 응용이 가능할 것으로 사료된다.

• 한국염색가공학회지
• /
• 제5권4호
• /
• pp.60-66
• /
• 1993

IPDI, PTAd 및 DMPA(음이온 중심)을 사용하여 폴리우레탄 아이오노머를 합성하고 여기에 물을 첨가하여 수분산 폴리우레탄을 제조하였다. 폴리올 분자량(Mn)이 분산상태 및 에멀젼 주사 필름의 열적, 기계적, 점탄성적 성질 및 팽윤에 미치는 영향을 측정하였다. 폴리올 분자량이 증가할수록 에멀젼 입경과 soft segment $T_{g}$는 감소하였으며, 용매팽윤, 에멀젼 점도, hard segment $T_{g}$는 증가하였다. 필름의 인장강도는 Mn = 1000에서 최소치를 나타냈으며, 파단신율은 폴리올 분자량 증가와 더불어 증가하였는데 이러한 결과는 soft-hard segment 상분리와 고분자량 PTAd의 결정화로 적절히 설명할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제70권6호
• /
• pp.683-702
• /
• 2019

The present study aims to analyze the magneto-electro-elastic (MEE) vibration of a functionally graded carbon nanotubes reinforced composites (FG-CNTRC) cylindrical shell. Electro-magnetic loads are applied to the structure and it is located on an elastic foundation which is simulated by visco-Pasternak type. The properties of the nano-composite shell are assumed to be varied by temperature changes. The third-order shear deformation shells theory is used to describe the displacement components and Hamilton's principle is employed to derive the motion differential equations. To obtain the results, Navier's method is used as an analytical solution for simply supported boundary condition and the effect of different parameters such as temperature variations, orientation angle, volume fraction of CNTs, different types of elastic foundation and other prominent parameters on the natural frequencies of the structure are considered and discussed in details. Design more functional structures subjected to multi-physical fields is of applications of this study results.

• Applied Microscopy
• /
• 제50권
• /
• pp.25.1-25.11
• /
• 2020

Scanning acoustic microscopy (SAM) or Acoustic Micro Imaging (AMI) is a powerful, non-destructive technique that can detect hidden defects in elastic and biological samples as well as non-transparent hard materials. By monitoring the internal features of a sample in three-dimensional integration, this technique can efficiently find physical defects such as cracks, voids, and delamination with high sensitivity. In recent years, advanced techniques such as ultrasound impedance microscopy, ultrasound speed microscopy, and scanning acoustic gigahertz microscopy have been developed for applications in industries and in the medical field to provide additional information on the internal stress, viscoelastic, and anisotropic, or nonlinear properties. X-ray, magnetic resonance, and infrared techniques are the other competitive and widely used methods. However, they have their own advantages and limitations owing to their inherent properties such as different light sources and sensors. This paper provides an overview of the principle of SAM and presents a few results to demonstrate the applications of modern acoustic imaging technology. A variety of inspection modes, such as vertical, horizontal, and diagonal cross-sections have been presented by employing the focus pathway and image reconstruction algorithm. Images have been reconstructed from the reflected echoes resulting from the change in the acoustic impedance at the interface of the material layers or defects. The results described in this paper indicate that the novel acoustic technology can expand the scope of SAM as a versatile diagnostic tool requiring less time and having a high efficiency.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.92-93
• /
• 2020

The test method to be developed is to determine whether the waterproof layer applied to the leak-prone part such as cracks and joints has defects such as tearing or lifting of the waterproof layer due to the influence generated from the behavior of the structure under complex deterioration conditions. This is to evaluate the performance of the waterproofing method afterwards. Therefore, by notifying only the pass or fail, the unique mechanical properties of the material or method used are notified to the test client to limit the physical properties of the test body, thereby determining and supplementing the weaknesses of the user material in advance to improve the high quality. We want to prevent damage from water leakage through production and distribution of materials.