• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1391-1398
• /
• 2009

The vibrating table method is widely used to estimate the minimum void ratio $e_{min}$. The existing method recommended in ASTM and KS F, however, can not consider the particle crushing during the vibrating table test. In this study, the particle cursing phenomenon was investigated by comparing vibrating table test with pluviation method using artificial sand (K-7). Vibrating table test for the artificial sand was confirmed which can crush of particle during the test. This study demonstrates that vibrating table test is an ineffective method to produce the more reliable $e_{min}$ of artificial sand.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1290-1295
• /
• 2008

The relative density of soil indicate loose and dense state of sand. Because sand is low compressibility, initial relative density of sand is important effect factor of compression and shear behavior. To measure exactly relative density, the exactly maximum and minimum void ratio was determinated by laboratory tests. Generally, vibrating table method is adapted for minimum void ratio(KS F 2345). However KS F 2345 is not consider the particle break during the vibrating table test. In this study, The minimum void ratio is compared with a method of Pluviation and Vibrating table test results using the K-7(crushed sand). It is concluded that the K-7 sand particles were crushed during the vibrating table test and vibrating table test is not a suitable test for a crushed sand $e_{min}$.

• Structural Engineering and Mechanics
• /
• v.28 no.6
• /
• pp.677-694
• /
• 2008

A vibration power minimization model is developed, based on the mobility matrix method, for a vibration isolation system consisting of a vibrating source placed on an elastic support structure through multiple resilient mounts. This model is applied to investigate the design optimization of an X-Y motion stage-based vibration isolation system used in semiconductor wire-bonding equipment. By varying the stiffness coefficients of the resilient mounts while constraining the dynamic displacement amplitudes of the X-Y motion stage, the total power flow from the X-Y motion stage (the vibrating source) to the equipment table (the elastic support structure) is minimized at each frequency interval in the concerned frequency range for different stiffnesses of the equipment table. The results show that when the equipment table is relatively flexible, the optimal design based on the proposed vibration power inimization model gives significantly little power flow than that obtained using a conventional vibration force minimization model at some critical frequencies. When the equipment table is rigid enough, both models provide almost the same predictions on the total power flow.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.160-165
• /
• 2002

Vibration table is required to obtain high packing density in expendable pattern casting process. Packing density, which is an important manufacture factor, depends on the vibration pattern induced by vibration table. In general, circular vibration pattern is recognized as the best pattern. The existing vibration table is investigated to identify current vibration pattern and consider a countermeasure. Modal test is utilized to identify the dynamic characteristics of vibration table, and finite element method is used to present the improved design.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.235-238
• /
• 2003

In this study, we propose a method of digital control to drive the vibrating gyroscope using electromagnetic-force. The gyroscope requires accurate vibration control and signal processing for high performance. Conventional PLL based analog controller is not only difficult to manufacture but also weak to outer environment such as temperatures, air pressures and etc. But digital controller using DSP can consistently maintain the cylinder vibration and perform digital signal processing regardless of disturbance. DSP's PWM function was utilized to control the vibration, and rotation-detecting algorithm was developed. Finally, the controller was verified by simulation and experiment using rotation-rate table.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.269-274
• /
• 2003

Vibration table is required to obtain high packing density in expendable pattern casting process. Packing density, which is an important manufacture factor, depends on the vibration pattern induced by vibration table. Modal test is utilized to identify the dynamic characteristics of vibration table. And finite element method is used to modify flask by fixing the stiffener. The positions of stiffener to modify are found and the natural frequency could be easily shifted to the objective value by using sensitivity analysis.

• Journal of Korea Foundry Society
• /
• v.24 no.5
• /
• pp.273-280
• /
• 2004

Vibrational motions of the compaction table were investigated to select the optimal operation conditions of sand filling and compaction for the EPC process. Their modes were measured at the nine points of the table with changing the relative rotation angles between the two eccentric mass vibrators which were attached parallel beneath the table. Well-defined vibration modes were measured at the center of the table but those of left and right sides of the table were distorted regardless of rotational angle differences. The distortion of vibration modes at both sides of the table were caused by the moment generated by offset positions of two eccentric masses. It was found that the uniform vibration modes would be gathered by controlling the relative distances between the rotating axis and the center of gravity in the compaction system at the various conditions of vibration modes and rotational angle differences.

• Journal of Korea Foundry Society
• /
• v.21 no.2
• /
• pp.104-110
• /
• 2001

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.297-302
• /
• 2007

Vibrating test of vehicle component can be possible in lab-based simulators instead of field testing owing to the development of technology in control algorithm as well as computational process. Currently, Multi-Axial Simulation Table(MAST) is recommended as a vibrating equipment, which excites a target component for 3-directional translation and rotation motion simultaneously and hence, vibrational condition can be fully approximated to that of real road test. But, the vibration-free performance of target component is not guaranteed with MAST system, which is only simulator subjective to the operator. Rather, the reliability of multi-axial vibration test is dependent on the quality of input profile which should cover the required severity of vibrating condition on target component. In this paper, multi-axial vibration testing methodology of vehicle component is presented here, from data acquisition of vehicle accelerations to the obtaining the input profile of MAST using severe data at proving ground. To compare the severity of vibration condition, between real road test and proving ground one, energy principle of equivalent damage is proposed to calculate energy matrices of acceleration data and then, it is determined the optimal combination of special events on proving ground which is equivalent to real road test at the aspects of vibration fatigue using sequential searching optimal algorithm. To explain the vibration methodology clearly, seat and door component of vehicle are selected as a example.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.8
• /
• pp.669-672
• /
• 2004

This paper considers the implementation and experiments of an open-loop Cylindrical Vibratory Gyroscope(CGV). An open-loop CGV composed of thin cylindrical vibrating element, electromagnetic drive and pick-off element with open-loop control was designed and fabricated. The experimental performance tests of the open-loop CGV were done using a temperature chambered rate table. Also, the limitations of open-loop CGV were analyzed and the solution for the limitations was proposed.