• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.215-218
• /
• 2002

HTS motors and generators have some advantages over LTS machines because of higher operating temperature. Very low temperature nakes LTS machines need higher refrigeration cost and large facilities. However, HTS machines are expected to be comparable with conventional counterparts at smaller machine ratings than LTS generators in terms of efficiency and size. As the operating temperature increases, the magnetic flux density generated by HTS field coils decreases relatively. For example, 1000hp HTS synchronous motor developed in a few years ago has maximum field density of 1.5T. At this point, magnetic material used in conventional machines is able to pass magnetic flux easily with high permeability. In order to investigate the effect, we arranged magnetic core only inside of magnet vessel of a 100hp target machine. By way of FEM analysis, we concluded that the magnetic core can reduce amount of expensive BSCCO conductor so much.

• Journal of Environmental Science International
• /
• v.7 no.4
• /
• pp.541-548
• /
• 1998

Aqueous phase adsorption of phenols by granular activated carbon was studied in a batch adsorption vessel. Adsorption Isotherms of phenol(Ph), p-chlorophenol(PCP) and p-nitrophenol (PNP) from aqueous solution on granular activated carbon have been obtained. The experimental data were analyzed by the surface and pore diffusion models. Both models could be applied to predict the adsorption phenomena. However, the pore diffusion model was slightly better than the surface diffusion model In representing the experimental data for the initial concentration changes. Therefore, the pore diffusion model was used to predict the change of operating variables such as the agitation speed and Particle size of adsorbent which have influence on the film resistance and intraparticle diffusion.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.1
• /
• pp.111-119
• /
• 1995

The elastic-plastic fracture toughness($J_{IC}$) and fracture resistance (J-R curve) of SA508-3 alloy steel used for nuclear reactor pressure vessel are investigated by using CT-type specimens. Fracture toughness tests are conducted by unloading compliance method and multiple specimen method at room temperature, -2$0^{\circ}C$ and 20$0^{\circ}C$. The apparent negative crack growth phenomenon which usually arises in partial unloading compliance test is well known. The negative crack growth phenomenon in determining J sub(IC) or J-R cure from partial unloading compliance experiments may be eliminated by the offset technique. In this study, the evaluation of $J_{IC}$ multiple specimen method recommended by the JSME gives the most reliable results by using half-size CT(similar-type) specimens.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.35-41
• /
• 1998

A Self-compensating liquid balancer is proposed, which consists of the vessel contains liquid available to compensate for rotor unbalance, and the vessel provides four sets of suction pipe and reservior. Under the centrifugal field the liquid moves through the pipe from the side of the unbalance mass to the reservior located on the symmetrically opposite side. The liquid balancer was confirmed experimentally to be useful for the balancing of rotor over the critical speed, and the whirling amplitude after balancing decreases to almost constant value in spite of the location and size of unbalance.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2012.06a
• /
• pp.121-122
• /
• 2012

In this research, we studied on improvement of the attraction force of solenoid operated valve for normal operation in harsh environment like vessel. Attraction force of the solenoid valves is effected by the B-H characteristics of magnetic material and the size of coil. In order to specify impact of the affection, we performed the B-H characteristics test and attraction force. Test results show that magnetic flux densities of the materials are difference each other more than 2 times in same magnetic intensity, and attraction force of the solenoid valve is 1.7 times difference as changes of resistance and the number of coil winding of solenoid.

• Fire Science and Engineering
• /
• v.19 no.3 s.59
• /
• pp.44-51
• /
• 2005

The flame propagation velocity and the flame arrival time of methyl alcohol, which is widely used as a material of paint industry and organic synthesis, d mixing solvent, and an analytical reagent, were examined at different temperatures and concentrations. It was found that the smaller the vessel size, the easier and faster the combustion. The maximum combustion velocity was 200 cm/sec in the small vessel at $30^{\circ}C$. The flame arrival time was determined to be longer with larger vessels. and shorter with higher concentrations.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.185-187
• /
• 2005

The reactor pressure vessel head of PWR has penetrations for control rod drive mechanism and instrumentation systems. The Primary coolant water and operating temperature can cause the stress-corrosion cracking of these nickel-based alloy penetrations. It is difficult to detect and size flaws such as SCC in the reactor head penetrations using conventional W methods because of complex geometry, Therefore, the utilities are using the TOFD technique for the detection and sizing of the flaw. This study shows the correlation between the ultrasonic wave direction and the orientation of the flaw and the range of flaw depth which can be detected by the TOFD techniques.

• Journal of Powder Materials
• /
• v.3 no.3
• /
• pp.167-173
• /
• 1996

The effect of ball milling on the pressureless sintering of MoSi$_2$ was investigated. Ball milling was conducted at 70 rpm for 72 hours using different balls and vessels: one used tungsten carbide balls in a plastic vessel(referred as B-powder) and the other stainless steel ball in a stainless steel vessel(referred as C- powder). The powder was compacted with 173MPa and subsequently sintered at the temperature range of 1150 $^{\circ}C$ and 1450 $^{\circ}C$ in H$_2$, atmosphere. Sintered density was measured and scanning electron micrograph was observed. Over 90% of the theoretical density was attained at 1250 $^{\circ}C$ within 10 minutes for C-powders, while the similar densification required a sintering temperature of 1450 $^{\circ}C$ for B-powders. Such a difference in sinterability between B and C-powders was discussed in terms of the effect of particle size reduction and activated sintering caused by Ni and/or Fe introduced during ball milling.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1148-1157
• /
• 2022

The maritime safety act defines a large vessel as a vessel of at least 200m in length overall. Since this standard was introduced in 1986, it has not been revised even though the marine traf ic environment has changed significantly. The length overall of 200m is equivalent to the handymax class for a dry bulker; therefore, classifying this as a modern large vessel size is difficult. Meanwhile, according to the maritime safety act, the specific sea area for traffic safety is established where large vessels frequently pass. Accordingly, by reviewing maritime-related laws, this study confirmed that standards for vessels larger than 200m in length overall were already introduced. Furthermore, by examining the statistics of vessels entering Korean ports, the existence of sea areas with a lot of traffic by large vessels, except the current 5 specific areas, was confirmed. Therefore, the following were suggested: the deletion of the term large vessel, a raise in the standard for length of a vessel related to a specific sea area in the maritime safety act.

• Journal of the Korean Institute of Navigation
• /
• v.11 no.2
• /
• pp.1-31
• /
• 1987

Nowadays, the transportation of almost all cargoes depends on sea routes in international trade. In the transaction of trade, cargo transportation must be completed on the base of two contrary objectives, one of which is to protect the vessel, cargoes and crew aborad her safely through every step of the transportation and the other is to pursue profits from the transaction of the trade. In spite of the great development of the modern techniques in shipbuilding today, many sea disaters of big merchant vessels have been occurring successively in winter seasons every year on the sea routes of the North Pacific Ocean. Whenever the accident of losing a vessel in rough sea occurred , many experts of the country to which the vessel belonged had tried to take out the reason of the missing without manifesting the exact cause of the unhappy occurrence. In this paper, we calculated ocean wave status along the route of the North Pacific Ocean theoretically concluded by us as optimum on the basis of weather and sea conditions. In the calculation, we used ITTC wave spectrum formula and meteorological data of "Winds '||'&'||' Waves of the north Pacific Ocean" edited by Ship Research Institute of Japan on the basic data assembled by World Meterological Organization through past 10 years. We selected three sample vessels of most common size in the North Pacific Ocean Routes, a container, a log carrier and a bulk carrier and applied tree sample vessels to the calculated sea conditions for getting the rolling angles of the vessels and stress exerting on the hulls. Examining the calculated results, we concluded as follows; 1. Under the condition of these status7 by beaufort scale, "heave to" maneuvering is the best and safest way to steer every vessel. 2. The most dangerous part of sea area along the west bound optimum route of the North Pacific Ocean in winter season, is the southern sea area of the Kamchatka peninsula.a peninsula.