• Nuclear Engineering and Technology
• /
• v.43 no.4
• /
• pp.391-398
• /
• 2011

The U metal chips generated in developing nuclear fuel and a gamma radioisotope shield have been stored under immersion of water in KAERI. When the water of the storing vessels vaporizes or drains due to unexpected leaking, the U metal chips are able to open to air. A new oxidation treatment process was raised for a long time safe storage with concepts of drying under vacuum, evaporating the containing water and organic material with elevating temperature, and oxidizing the uranium metal chips at an appropriate high temperature under conditions of controlling the feeding rate of oxygen gas. In order to optimize the oxidation process the uranium metal chips were completely dried at higher temperature than $300^{\circ}C$ and tested for oxidation at various temperatures, which are $300^{\circ}C$, $400^{\circ}C$, and $500^{\circ}C$. When the oxidation temperature was $400^{\circ}C$, the oxidized sample for 7 hours showed a temperature rise of $60^{\circ}C$ in the self-ignition test. But the oxidized sample for 14 hours revealed a slight temperature rise of $7^{\circ}C$ representing a stable behavior in the self-ignition test. When the temperature was $500^{\circ}C$, the shorter oxidation for 7 hours appeared to be enough because the self-ignition test represented no temperature rise. By using several chemical analyses such as carbon content determination, X-ray deflection (XRD), Infrared spectra (IR) and Thermal gravimetric analysis (TGA) on the oxidation treated samples, the results of self-ignition test of new oxidation treatment process for U metal chip were interpreted and supported.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.453-457
• /
• 2007

Interest in use of ink-jet printing for pattern-on-demand fabrication of metal interconnects without complicated and wasteful etching process has been on rapid increase. However, ink-jet printing is a wet process and needs an additional thermal treatment such as an annealing process. Since a metal ink is a suspension containing metal nanoparticles and organic capping molecules to prevent aggregation of them, the microstructure of an ink-jet printed metal interconnect 'as dried' can be characterized as a stack of loosely packed nanoparticles. Therefore, during being treated thermally, an inkjet-printed interconnect is likely to evolve a characteristic microstructure, different from that of the conventionally vacuum-deposited metal films. Microstructure characteristics can significantly affect the corresponding electrical and mechanical properties. The characteristics of change in microstructure and electrical resistivity of inkjet-printed silver (Ag) films when annealed isothermally at a temperature between 170 and $240^{\circ}C$ were analyzed. The change in electrical resistivity was described using the first-order exponential decay kinetics. The corresponding activation energy of 0.44 eV was explained in terms of a thermally-activated mechanism, i.e., migration of point defects such as vacancy-oxygen pairs, rather than microstructure evolution such as grain growth or change in porosity.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.141-145
• /
• 2016

Polymer electrolyte membranes (PEMs) are key components to determine electrochemical fuel cell performances, in addition to electrode materials. The PEMs need to satisfy selective transport behaviors to small molecules including gases and protons; the PEMs have to transport protons as fast as possible, while they should act as hydrogen barriers, since the permeated gas induces the thermal degradation of cathode catalyst, resulting in rapid electrochemical reduction. To date, limited tools have been used to measure how fast hydrogen gas permeates through PEMs (e.g., Constant volume/variable Pressure (time-lag) method). However, most of the measurements are conducted under vacuum where PEMs are fully dried. Otherwise, the obtained hydrogen permeance is easily changeable, which causes the measurement errors to be large. In this study, hydrogen permeation properties through Nafion212 used as a standard PEM are evaluated using an in-situ measurement system in which both temperature and humidity are controlled at the same time.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1229-1232
• /
• 1994

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. This paper describes the effects of lithium salts, plasticizer addition and temperature dependence of conductivity of PEO electrolytes. Polyethylene oxide(PEO) based polymer electrolyte films were prepared by solution casting an acetonitrile solution of preweighed PEO and Li salt. After solvent evaporation, the electrolyte films were vacuum-dried at $60^{\circ}C$ for 48h, the thickness of the films were $90{\sim}110{\mu}m$. The conductivity properties of prepared PEO electrolytes are summarized as follows. PEO electrolyte complexed with $LiClO_4$ shows the better conductivity of the others. $PEO-LiClO_4$ electrolyte when $EO/Li^+$ ratio is 8, showed the best conductivity. Optimum operating temperature of PEO electrolyte is $60^{\circ}C$. By adding propylene carbonate and ethylene carbonate to $PEO-LiClO_4$ electrolyte, its conductivity was higher than $PEO-LiClO_4$ without those. Also $PEO_8LiClO_4$ electrolyte remains static up to 4.5V vs. $Li/Li^+$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.152-152
• /
• 2016

Anodizing is a technology to generate thicker and high-quality films than natural oxide films by treating metals via electrochemical methods. It is a technique to develop metals for various uses, and extensive research on the commercial use has been performed for a long time. Aluminum anodic oxide (AAO) is generate oxide films, whose sizes and characteristics depending on the types of electrolytes, voltages, temperatures and time. Electrochemical manufacturing method of nano structure is an efficient technology in terms of cost reduction, high productivity and complicated shapes, which receives the spotlight in diverse areas. The sulfuric acid was used as an anodizing electrolyte, controlling its temperature to $10^{\circ}C$. The anode was 5083 Al alloy with dimension of $5(t){\times}20{\times}20mm$ while the cathode was the platinum. The distance between the anode and the cathode was maintained at 3 cm. Agitation was introduced by magnetic stirrer at 300 rpm to prevent localized temperature rise that hinders stable growth of oxide layer. In order to observe surface characteristics with applied current density, the electrolyte temperature, concentration was maintained at constant condition for $10^{\circ}C$, 10 vol.%, respectively. To prevent hindrance of stable growth of oxide layer due to local temperature increase during the experiment, stirring was maintained at constant rate. In addition, using galvanostatic method, it was maintained at current density of $10{\sim}30mA/cm^2$ for 40 minutes. The cavitation experiment was carried out with an ultrasonic vibratory apparatus using piezo-electric effect with modified ASTM-G32. The peak-to-peak amplitude was $30{\mu}m$ and the distance between the horn tip and specimen was 1 mm. The specimen after the experiment was cleaned in an ultrasonic, dried in a vacuum oven for more than 24 hours, and weighed with an electric balance. The surface damage morphology was observed with 3D analysis microscope. As a result of the investigation, differences were observed surface hardness and anti-cavitation characteristics depending on the development of oxide film with applied current density.

• Resources Recycling
• /
• v.17 no.3
• /
• pp.21-28
• /
• 2008

Using the post-consumer waste and edge scrap mixed PET with small amount PP air filter elements of automobiles. It was studied that these mixed waste plastics of the various types of the PET were practicable for the material recycling. Various waste PET/PP plastics were collected, crushed, dried in vacuum, and extruded to recycled PET/PP chips. These chips were mixed with three kinds compatibilizers, EVA, MBS, and recycled PVB of the ratio of $3{\sim}10wt.%$ for the purpose of the compatibility for the post-consumer waste and edge scrap. We investigated mechanical and thermal properties of PET/PP mixtures which were compound with the weight ratio of compatibilizers. Compatibilizer, MBS application was showed the most excellent mechanical properties in the range of the $3{\sim}5wt.%$ EVA application was displayed good impact strength and thermal property in the range of $3{\sim}5wt.%$ Last, recycled PVB application was showed poor mechanical properties in the whole range ratio of the PVB.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.593-596
• /
• 2004

We are developing a micro-solid propellant rocket array thruster for simple attitude control of a 10 kg class micro-spacecraft. The prototype has ø 0.8 mm solid propellant micro-rockets arrayed at a pitch of 1.2 mm on a 22 x 22 mm substrate. In previous studies, an impulse thrust of 4.6 x 10$^{-4}$ Ns was obtained in vacuum, but we found the problems of unacceptably low ignition success rate and incomplete combustion. This paper describes experiments to improve the ignition rate. In order to achieve this goal, we tried to solidify paste-like ignition aid (RK) on the ignition heaters with strong adhesion. To make the paste-like RK, isoamyl acetate was added to RK powder. We tested 9 rockets, but only 2 rockets were ignited with huge ignition energy. This is because the heat con-duction between the ignition heater and the RK was too low to ignite the RK, since dried RK had a lot of pores. Also, a large cavity was sometimes found just above the ignition heater.

• Korean Journal of Food Science and Technology
• /
• v.35 no.2
• /
• pp.211-216
• /
• 2003

Absorption characteristics of hot air-. vacuum-, and freeze-dried ginger powder were investigated. Monolayer moisture content as determined by GAB equation was $0.257{\sim}0.540\;H_2O/g$, showing higher significance than BET equation. Absorption enthalpy was calculated based on different drying methods and water activities. Absorption energy decreased with increasing water activity but was not affected by drying method. Isotherm curves showed a typical sigmoid form. Among models applied for predicting equilibrium moisture content, Caurie model was the best fit model for ginger powder, showing the lowest prediction deviation of $1.2{\sim}5.4%$, followed by Henderson then Bradley models. The prediction model equations for the moisture content were established by in(time), water activity, and temperature.

• Korean Journal of Microbiology
• /
• v.5 no.2
• /
• pp.79-85
• /
• 1967

Kim, Jong Hyup., (Div. of Biology, Atomic Energy Research Institute,Korea.;) Studies on the Cellulor Metabolism in Microorganisms as influenced by Gamma-irradiation(III): On the Changes of Free Amino acid Pool and content of Protein in Yeast clls irradiated by .gamma.-ray. 1. The strain of Saccharomyces cerevisiae had been cultured synchronously in aerobic condition and irradiatel by gamma-ray from the source of cobalt-60. Drying in vacuum oven at $90^{\circ}C$ C over 12 hours, then changes of protein content (Kjeldahl) and free amino acid pool have been assayed with use of spectrophotometer. Results obtained were compared with those of unirradiated normal cells. 2. It is proved that amount of protein content in the irradiated cells increases to seven percent more than those of normal cells in the same weight of dried samples. It seems like carbohydrate breakown had been stimulated by irradiation and that relative contents of protein shows higher values than those of normal in the same weight of samples. 3. The amount of free amino acid pool in the irradiated cells shows less value about ten percent than those of normal cells, and rate of decreasing is also weak than those of standard reagent solution of amino acid. We may assume that free amino acid pool would be protected against radiation damage in living cells and more stable than in vitro. 4. The component of free amino acid pool have been assayed on second dimensional paper chromatogram, and the identified amino acids are as follows; aspartic acid, serine, glutamic acid, cystine, lysine, glycine, threonine, histidine, arginine, tyrosine, phenylalanine, valine and leucine. 5. Distributional presence of free amino acids are identical to that of normal cells except arginine, it is cosumable that radiation effect is univerlsal to all amino acid. However it is obvious that there are differences in radiolabilities of amino acids in irradiated cells.

• Polymer(Korea)
• /
• v.28 no.5
• /
• pp.433-443
• /
• 2004

The membranes of the blends of chitosan and polycaprolactarn (PA6) were prepared in formic acid. FT-IR data revealed that hydrogen bonding between amide and hydroxyl groups of chitosan and PA6, respectively, was formed. Thermogravimetric analysis demonstrated that the blend samples contain water. DMA results showed that the dissipation of water in the samples significantly reduced the storage modulus (E'). The mechanical loss tangent (tan $\delta$) data of the blend samples showed the $\beta$d loss peak around $0^{\circ}C$. The blend samples were completely dried in a vacuum and then exposed to high moisture to absorb water which would cause, so called, w-bridges between the molecules. The E' data of these regained samples increased abnormally and additional loss peak appeared on the shoulder of the peak around $50^{\circ}C$. Under dry condition, the samples with a blend ratio of 40/60 for chitosan/PA6 displayed a better miscibility between two components.