• 태양에너지
• /
• 제11권1호
• /
• pp.41-49
• /
• 1991

본 연구에서는 기판의 증착온도를 $200{\pm}5[5^{\circ}C]$로 유지하여 진공증착법으로 (P)SiC/(N)Si 태양전지를 제작하고 그의 특성을 조사하였다. SiC 박막의 최적 두께 $1.2[{\mu}m]$는 박막두께와 변환효율과의 관계로부터 정해졌고 태양전지의 특성은 열치리에 의하여 개선되었다. 최적조건의 열처리 온도와 시간은 $420[^{\circ}C]$에서 12분이고 분광응답의 피크값은 열처리 온도의 증가와 더블어 장파장 쪽으로 이동함을 알았다. X선 회절분석 및 SEM검사는 열처리 온도와 시간에 따라 SiC 박막내에서 결정성장을 보여주며 $2.5{\times}1[cm^2]$의 태양전지에서 최고 변환효율은 11.7[%]이다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2014년도 추계학술대회
• /
• pp.917-920
• /
• 2014

우리나라는 1995년 이동전화 가입자수가 백만명, 1998년 천만명을 돌파하고 비약적으로 증가하여 현재 우리나라는 인구대비 이동통신단말기의 보급률이 110%를 넘어섰다. 현재는 어린이나 학생 등 비경제 활동 인구들까지 이동통신 단말기를 사용하고 있다. 명백히 필수재가 된 이동통신 단말기는 그 보급대수가 냉장고, 세탁기, 진공청소기, 승용차를 추월하고 있다. 그런데 이동통신의 생활화는 우리의 생활을 편리하게 하며 이동통신 단말기는 아주 중요한 필수재로 자리매김하였으나 단말기 대금을 비롯한 통신관련 비용은 가계의 큰 부담이 되고 있다. 그런데 공정한 경쟁을 통하여 소비자 후생 나아가 사회적 후생을 최대화 할 수 있도록 시장의 실패를 방지해야할 정부는 적시에 적절한 역할을 하지 못하고 있는 것으로 보인다. 이는 주인-대리인(principal-agent)관점에서도 이해될 수 있을 것이다. 이동통신전화가 상용화된 1990년대 초부터 현재까지의 이동통신정책중 이동통신망의 공동이용, 번호이동, 단말기 유통과 이통서비스의 분리, 망중립성 확보는 주인-대리인문제와 관련한 문제점들을 노정하고 있다.

• 대한금속재료학회지
• /
• 제48권4호
• /
• pp.357-362
• /
• 2010

Ferromagnetic Mn-Al nanoparticles were prepared using a plasma arc discharge method. The influence of the process parameters on the vaporization rate, composition, particle size, and magnetic properties of the as-produced nanoparticles was investigated. The Mn content was found to be higher in the nanoparticles than in the corresponding mother materials, although the difference diminished with the reaction time. As the $H_2$ content in the reaction gas increased, both the vaporization rate and the particle size increased. With 30 at.% Mn, the average particle diameter was 35.2 nm under a pure Ar gas condition, whereas it was 95.4 nm at a Ar:$H_2$ ratio of 60:40. With the addition of a small amount of carbon, ${\varepsilon}$-phase nanoparticles were successfully synthesized. After a heat treatment in a vacuum for 30 min at $500^{\circ}C$, the nonmagnetic ${\varepsilon}$-phase was transformed into the ferromagnetic ${\tau}$-phase, and a very high coercivity of nearly 5.6 kOe was achieved.

• 한국안전학회지
• /
• 제35권6호
• /
• pp.78-84
• /
• 2020

The F&EI technique is one of the risk assessments with many advantages. It can save time and effort compared to quantitative risk assessment (QRA). By using the evaluation result of this technique, it is possible to check the effectiveness of the investment cost. In addition, a relative risk ranking can be created and used to establish the facility management cycle and to prioritize investment. However, evaluating the target process can be evaluated more than the actual risk since the LCCF, a loss prevention measure, is too limited. In addition, calculating premiums via this method can result in excessive premiums, making it difficult to evaluate the risk precisely. Therefore, new safety guard was added to the LCCF of the F&EI risk assessment with reference to HAZOP and LOPA techniques. Newly added LCCFs are Deflagration arrester, Check valve, SIS, and Vacuum beaker, etc. As a case study, F&EI risk assessment was performed on Acetone storage tank of a API (Active pharmaceutical ingredient) plant to compare actual MPPD. The estimated loss amount was 592,558$ for the existing technique and 563,571$ for the improved technique, which was reduced by about 5% compared to the previous one.This proved that a more precise evaluation is possible and that the efforts for safety at the workplace are reflected in the evaluation results.

• 한국수소및신에너지학회논문집
• /
• 제32권3호
• /
• pp.163-171
• /
• 2021

Securing energy sources is a key element essential to economic and industrial development in modern society, and research on renewable energy and hydrogen energy is now actively carried out. This research was conducted through experiments and analytical methods on the hydrogen filling process in the hydrogen storage tank of the hydrogen charging station. When low-temperature, high-pressure hydrogen was injected into a high-pressure tanks where hydrogen is charged, the theoretical method was used to analyze the changes in temperature and pressure inside the high-pressure tanks, the amount of hydrogen charge, and the charging time. The analysis was conducted in the initial vacuum state, called the First Cycle, and when the residual pressure was present inside the tanks, called the Second Cycle. As a result of the analysis, the highest temperature inside the tanks in the First Cycle of the high-pressure tank increased to 442.11 K, the temperature measured through the experiment was 441.77 K, the Second Cycle increased to 397.12 K, and the temperature measured through the experiment was 398 K. The results obtained through experimentation and analysis differ within ±1%. The results of this study will be useful for future hydrogen energy research and hydrogen charging station.

• 반도체디스플레이기술학회지
• /
• 제21권4호
• /
• pp.106-109
• /
• 2022

The green-emitting Zn₂SiO₄:Mn²⁺ phosphor film was evaluated in a xenon excimer lamp. The phosphor film with 2 ㎛ thick was formed of monolithic structure on the inner side of quartz through a long-time annealing process of coated ZnO solution doped with Mn²⁺ ion and SiO₂ of quartz tube. The coated quartz was filled with 100 torr of xenon gas, and simultaneously both sides was melt and sealed. The xenon-field quartz tube was discharge by applying the voltage of 15 kV with a frequency of 26 kHz, and emitted the glow with dominant peak at 172 nm. The vacuum ultraviolet excited the inner-side coated Zn₂SiO₄:Mn²⁺ phosphor film, which emitted the pure and strong green light.

• Nuclear Engineering and Technology
• /
• 제54권10호
• /
• pp.3614-3619
• /
• 2022

To operate the ion cyclotron resonance heating (ICRH) antennas in a better heating state and produce relatively low impurities, it is necessary to control the antenna spectrum by changing the antenna phasing. As the electrical length of the antenna feeding transmission lines is changing as a matter of the standing wave pattern at the ceramic supports, 90° elbows, T-connectors and antenna loops, we chose to measure the current at the grounding points of the antenna loops by antenna strap probe. The voltage drops along a small, several millimeter-long paths at the end of the antenna loops give a signal that is proportional to the current in the antenna loop. Through the simulation of the antenna strap probe and the actual measurement of the antenna phasing under vacuum conditions, the reliability of the antenna strap probe based diagnostic system have been successfully proved. Moreover, this system was successfully applied to the ICRH daily experiments in the spring of 2021. In the near future, the active real-time feedback control of the antenna phasing system will be developed based on this diagnostic system in the EAST tokamak.

• 반도체디스플레이기술학회지
• /
• 제21권1호
• /
• pp.79-84
• /
• 2022

As various flexible display products are released, the demand for high-performance colorless and transparent polyimide (CPI) film is continuously increasing. The primary purpose of this study is to establish a systematic procedure for optimizing the optical performance of CPI films by applying the response surface method. After selecting three key factors (monomer type, stirring time for varnish synthesis, and maximum temperature of vacuum furnace for film production) affecting optical performance based on experiences and references, CPI films were manufactured according to the experimental sequence designed by the central composite design, and then the yellowness index (YI) and optical transmittance (Tr) of the films were measured. When producing a CPI film by pouring varnish into a petri dish, the change in optical properties according to thickness should be considered, and there was a meaningful linear relationship between YI and Tr. The species of monomer and the maximum temperature were the critical factors that had an influence on YI and Tr, respectively. It is expected that the procedure proposed in this study can serve as a starting point for CPI film optimization studies considering the other factors that were not considered and responses such as thermal properties.

• 한국환경보건학회지
• /
• 제48권1호
• /
• pp.52-58
• /
• 2022

Background: Few studies have evaluated the exposure to phthalates via inhalation of floor dust in children's living areas. Objectives: This study evaluated the concentration and exposure level of phthalates emitted from indoor floor dust in children's living areas. Methods: This study utilized the results of a survey conducted by the Ministry of Environment in 2019. Indoor dust was collected from 150 households with children aged 3~7 and 67 daycare centers or local children's centers by using vacuum cleaners. It was analyzed by gas chromatography mass spectrometry. Six types of phthalates were analyzed: Bis (2-ethylhexyl) phthalate (DEHP), Dibutyl phthalate (DBP), Benzyl butyl phthalate (BBP), Di-N-octyl phthalate (DNOP), Diisononyl phthalate (DINP), Di -isodecyl phthalate (DIDP). Results: The medians of DEHP concentrations were 1,028 and 1,937 mg/kg in homes and daycare centers, respectively. The median and maximum values of daily intake were calculated by applying the median and 95th percentile values (the upper 5% of the total concentration) in dust measured in the homes. The DEHP median value was 1.6 ㎍/kg/bw/day, and a maximum A value of 7.8 ㎍/kg/bw/day was calculated. When the childcare center values were applied, the median daily intake of DEHP was 3.1 ㎍/kg/bw/day and the maximum value was 29.2 ㎍/kg/bw/day. As a result of calculating the daily intake by integrating the values of home and childcare facilities, the median and maximum values of daily intake were 1.9 and 10.9 ㎍/kg/bw/day, respectively. Conclusions: This study derives phthalate concentrations among the floor dust in homes and childcare facilities where children mainly spend time, and suggests their intake of phthalates through this. In particular, it was newly suggested that the phthalate concentrations in homes and childcare facilities are different, resulting in differences in intake.

• 전기전자학회논문지
• /
• 제27권4호
• /
• pp.610-616
• /
• 2023

본 논문에서는 Robot Operating System(ROS) 기반의 모바일 매니퓰레이터(Manipulator)를 이용한 무인 배송 로봇 시스템을 구현하고 시스템 구현을 위해 사용된 기술에 대해 소개한다. 로봇은 엘리베이터를 이용해 건물 내부에서 자율주행이 가능한 모바일 로봇과 진공 펌프를 부착한 Selective Compliance Assembly Robot Arm(SCARA)-Type의 매니퓰레이터로 구성된다. 로봇은 매니퓰레이터에 부착된 카메라를 이용하여 이미지 분할과 모서리 검출을 통해 배송물을 들어올리기 위한 위치와 자세를 결정할 수 있다. 제안된 시스템은 스마트폰 앱 및 ROS와 연동된 웹서버를 통해 배송 현황을 조회하고 로봇의 실시간 위치를 파악할 수 있도록 사용자 인터페이스를 가지고 있으며, You Only Look Once(YOLO)와 Optical Character Recognition(OCR)을 통해 배송 스테이션에서 배송물과 주소지를 인식한다. 아울러 4층 건물 내부에서 진행한 배송 실험을 통해 시스템의 유효성을 검증하였다.