• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.816-822
• /
• 2011

Pervaporation is known to be a low energy consumption process since it needs only an electric power to maintain the permeate side in vacuum. Also, the pervaporation is an environmentally clean technology because it does not use the third material such as an entrainer for either an azeotropic distillation or an extractive distillation. In this study, Silicalite-1 particles are hydrothermally synthesized and polydimethylsiloxane(PDMS)-zeolite composite membranes are prepared with a mixture of synthesized Silicalite-1 particles and PDMS-polymer. They are used to separate n-butanol from its aqueous solution. Pervaporation characteristics such as a permeation flux and a separation factor are investigated as a function of the feed concentration and the weight % of Silicalite-1 particles in the membrane. A 1,000 $cm^3$ aqueous solution containing butanol of low mole fraction such as order of 0.001 was used as a feed to the membrane cell while the pressure of the permeation side was kept about 0.2~0.3 torr. When the butanol concentration in the feed solution was 0.015 mole fraction, the flux of n-butanol significantly increased from 14.5 g/ $m^2$/hr to 186.3 g/$m^2$/hr as the Silicalite-1 content increased from 0 wt% to 10 wt%, indicating that the Silicalite-1 molecular sieve improved the membrane permselectivity from 4.8 to 11.8 due to its unique crystalline microporous structure and its strong hydrophobicity. Consequently, the concentration of n-butanol in the permeate substantially increased from 0.07 to 0.15 mole fraction. This composite membrane could be potentially appliable for separation of n-butanol from insitu fermentation broth where n-butanol is produced at a fairly low concentration of 0.015 mole fraction.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.37-42
• /
• 2016

The purpose of this paper is to study for the emission gas control of passenger car. The first example, the PCSV never open when operating condition, but it opened by causing malfunction because of trouble. As a result, the purge gas entered into surge tank, a mount of fuel was displayed with excessive supply on tester. Therefore, it certified the bad-condition of the engine when idling by decreasing of fuel injection quantity from engine ECU. The second example, the hose activating a EGR valve didn't supply the vacuum pressure because of assembling the other part. Thus, it knew the bad-condition of engine that the EGR valve would not work normally by leaking with the other port. The third example, as the rear oxygen sensor of two sensor were fault-installing by changing the sensor of other a car it could not detect of oxygen quantity. Finally, it found the phenomenon of abruptly decreasing vehicle speed when braking a car. Therefore, the system including with emission control has to drastically manage by maximizing condition to role decreasing the emission gas.

• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.780-788
• /
• 1995

The purpose of this study was to compare the apical seal following root canal shaping by different methods. From fourty extracted mandibular 1st and 2nd molars, fourty mesial roots whose canals have some degree of curvature were selected. The mesiobuccal root portion including mesiobuccal portion of a crown was sectioned in each molar. After access cavity preparation for the mesiobuccal canal, working length was determined with # 10 K-file. The sectioned roots were implanted in acrylic resin block and randomly divided into four groups. The canals of group I were shaped by step-down/balanced force, group II by stepdown/step-back, group III by step-back and group IV by conventional method. All of the shaped canals were obturated by Thermafil method and access cavities were filled with IRM. The roots were removed from acrylic resin block and placed in 100 % humidity for 7days. Except the root surfaces of apical 2mm, the root surfaces were nail-varnished 3 times. After the roots were placed in 700 torr vacuum pressure for 15 minutes, they were immersed in 2% methylene blue solution for 4 days. Nail varnishes were removed with acetone. After that, the roots were decalcified in 5 % nitric acid and dehydrated with alcohol series. Transparent specimens were made by methyl salicylate and the quality of apical seal was assessed by measuring the leakage linearly. The results were as follows. 1. The leakage in canals shaped by step-down/balanced force method was significantly less than that in canals shaped by step-back method(P<0.05) and was less but not statistically than that in canals shaped by step-down/step-back method (P>0.05). 2. The leakage in canals shaped by step-down/step-back method was less than that in canals shaped by step-back method, but there was no statistical significance(P>0.05). 3. The leakage in canals shaped by conventional method was significantly more than that in canals shaped by step-down/balanced force, step-down/step-back and step-back method (P<0.05).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.142-145
• /
• 2005

AC-PDP에서 발광 휘도와 발광 효율의 개선은 매우 중요한 과제중의 하나이다. 높은 발광 휘도와 발광 효율을 위해선 VUV의 높은 발광 효율이 요구되어진다. 이 실험에서는 AC-PDP에서 Ne-Xe의 2원 혼합기체와 He-Ne-Xe의 3원 혼합기체의 VUV 발광 세기를 측정하였다. 기체 압력은 200 Torr, 300 Torr, 400 Torr, 500 Torr로 유지하였고, Xe 혼합비는 1%, 2%, 4%, 7%, 10%, 15%를 사용하였다. 진공자외선 발광 세기는 He-Ne-Xe의 3원 혼합기체가 Ne-Xe의 2원 혼합기체보다 발광 세기가 훨씬 높다는 것을 알 수 있었다. 그리고 Xe 함량이 증가함에 따라 공명선인 147 nm의 발광 세기는 Xe 혼합비가 약 10%까지는 증가하다가 10% 이후에는 포화되고, 반면 분자선인 173 nm은 Xe 함량과 가스 압력이 증가함에 따라 발광 세기가 증가하였다.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.39-44
• /
• 2009

Polymer substrates were fabricated by using poly (phenylene ether) as a base resin, N,N'-m-phenylenedimaleimide (PDMI) as a crosslinking agent and decabromodiphenylethane as a flame retardant. The effects of crosslinking agent and flame retardant on physical properties such as dielectric property of the substrate were investigated. Thermal curing feature of PDMI with or without an initiator was analyzed by DSC, and then, PPE-PDMI test compositions were designed based on this result. Composite sheets were cast by film coater, laminated under vacuum and pressure, and then, the changes of dielectric constant, dielectric loss, peel strength, solder heat resistance and inflammability according to increasing amount of PDMI and flame retardant were evaluated, Dielectric constant and dielectric loss showed increasing trend with increasing amount of PDMI and flame retardant, but solder heat resistance and inflammability were improved. Peel strength was obtained higher than 1 kN/m when PDMI above 10 wt% was added, but slightly decreased as the amount of flame retardant increased. From the measured gel contents, the reaction mechanism of PPE-PDMI system was deduced to the formation of network structure by crosslinking PDMI with PPE rather than the formation of semi-IPN structure. In conclusion, the polymer composite substrate materials with dielectric constant of 2.52$\sim$2.65 and dielectric loss below 0.002 at 1 GHz were obtained and they will be proper for high frequency applications.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.566-575
• /
• 2013

The fruits of Taxus cuspidata were collected, divided into seeds and fruits, and extracted with 95% EtOH. The extracts were evaporated under the reduced vacuum pressure, concentrated, then successively fractionated with a series of n-hexane, dichloromethane, ethyl acetate and water on a separatory funnel to get some freeze dried samples. A portion of the EtOAc (arils:1.65 g, seeds:1.04 g) and $H_2O$ (arils:7 g, seeds:10 g) soluble samples were chromatographed on a Sephadex column using MeOH-$H_2O$ (1:1, 1:3, 1:5, v/v), EtOH-hexane (3:1, v/v) mixture and 100% $H_2O$ as eluting solvents to isolate pure compounds from the fractions. The isolates were developed by cellulose TLC using t-BuOH-HOAc-$H_2O$ (TBA; 3:1:1, v/v/v) and 6% aqueous HOAc. Visualization was done under ultraviolet light and by spraying the vanillin-HCl-EtOH reagent (4.8:12:480, v/v/v). followed by heating. The structures of the isolates were characterized by $^1H$- and $^{13}C$-NMR, DEPT, 2D-NMR, LC/MS and EI-MS spectra. In addition to the NMR and MS spectra, acid hydrolysis and permethylation were used to determine the correct structure of the isolated sugar compound. Their structures were elucidated as (+)-catechin (1), (-)-epicatechin (2), (+)-gallocatechin (3), (-)-epigallocatechin (4) and ${\beta}$-D-fructofuranose-($2{\rightarrow}4$)-O-${\beta}$-D-glucopyranose($1{\rightarrow}4$)-O-${\alpha}$-D-glucopyranose ($1{\rightarrow}2$)-O-${\beta}$-D-fructofuranose (5) on the basis of the above experimental evidences.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2019

Ground and high altitude simulated combustion experiments were conducted using a liquid rocket engine with hydrogen peroxide and kerosene as the propellant. A ground and high altitude simulated combustion test facility was constructed by installing a high altitude model diffuser and TMS (Thrust Measuring System) on a vertical combustion test bench. The thrust characteristics according to altitude were investigated using the combustion test equipment. The diffuser was designed on a 1:4.8 scale to verify the characteristics of the high diffusing diffuser and starting pressure. The cold flow tests were conducted using nitrogen gas, and the performance characteristics and starting characteristics of the scale down diffuser were verified. A diffuser and TMS were installed on the vertical combustion test bench, and the thrust correction equations for the system resistance were derived. The thrust correction equations were derived from the step test and vacuum step test before the actual hot firing test. Nozzles with an operating altitude of 10km were designed. Hot firing tests were conducted to analyze the thrust characteristics according to the operating altitude changes. The actual thrust was calculated using each correction equation with the thrust value measured by the TMS.

• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.244-252
• /
• 2019

This study investigated the effect of addition of aromatics such as Toluene/LCO/resin on the coke depression and asphaltene conversion. The experiment was carried out with vacuum residue as a feedstock with Molybdenum dispersed catalysts under the slurry-phase hydrocracking condition (Temp. of $425^{\circ}C$, $H_2$ pressure of 80 bar at $80^{\circ}C$, reaction time of 4 hr, Mo-concentration of 500 ppm). As results, the coke reduction was shown to be similar irrespective of types of aromatics, while asphaltene was more converted to gas and maltene when LCO and resin with higher dipole moment were added. The addition of aromatics with change of reaction time showed no difference in terms of depression of coke formation. But the addition of LCO rather increased the coke yield after 2 hr. And it was found that asphaltene in liquid phase had the higher aromaticity index so that asphaltene is difficult to disperse in oil phase.

• Journal of Conservation Science
• /
• v.37 no.6
• /
• pp.821-830
• /
• 2021

The weapons excavated from the de-militarized zones (DMZ) of Korea are vulnerable to corrosion due to the immediate and drastic environmental change. Especially, the chloride ions (Cl^-) in iron weapons cause active corrosion and require removal. In this study, conservation treatment and de-salination was performed for the discovered weapons from excavation sites of soldiers killed in action during the Korean War. Furthermore, an attempt was made to prepare the most stable plan for conservation treatment through the comparative study of soaking weapons in distilled water without chemicals and in a solution of sodium (SSC) at different temperatures. In the preliminarily experiments, the comparison of the eluted Cl^- ions according to different conditions of de-salination showed that the highest number of ions were detected from the de-salination with SSC at a temperature of 100℃, and its duration was much smaller, i.e., 1~2 weeks. Accordingly, for the parts from the guns and rifles amongst other objects, a six-time de-salination was conducted in the SSC solution for 8 hours at 100℃ and subsequently, for 16 hours at room temperature during which the distilled water and SSC were exchanged every week. However, in the case of a loaded rifle, the de-salination was not conducted, considering the risk that the high temperature and pressure by impregnation in vacuum could cause an explosion

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.6
• /
• pp.431-446
• /
• 2023

Samama wood (Anthocephalus macrophyllus (Roxb) Havil) is a fast-growing and lesser-utilized wood species that has inferior properties; therefore, its quality needs to be improved. This research aimed to determine the effect of citric acid impregnation at high curing temperatures on the dimensional stability and mechanical properties of wood. Citric acid solution with 10% concentration (w/w) was impregnated into wood samples by vacuum-pressure method (-0.5 cmHg, 30 min; 0.7 MPa, 3 h), followed by curing process at 140℃, 160℃, and 180℃ of temperature for 1 h. In comparison, the other wood samples were heat treated at the same temperatures and time. The results showed that the increase in curing and heat temperatures for both treatments were directly proportional to the dimensional stability, but inversely proportional to the mechanical properties. Citric acid impregnated had higher density, dimensional stability, and mechanical properties, except for modulus of rupture, than that of heat treatment. The optimum temperature is suggested at 160℃ in both treatments.