• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.833-841
• /
• 2010

In this report, the test results of five reinforced concrete beam-column joint subjected to cyclic load are presented. The main purpose of the research is to investigate the influence of the steel pull-out of the beam-column joints to the shear and ductile capacity of the RC beam-column assembles. In addition, the influence of the amount of beam reinforcement to the joint shear and ductile capacity is evaluated. Test results indicate that the yield penetration of steel bar increases as the joint shear strength ratio, $V_{j1}/V_{jby}$ decreases. And the slippage of the steel bars are varied according to the region of the beam-column joints. The pull-out of the steel bars of five specimens was almost the same regardless of the joint shear strength ratio, $V_{j1}/V_{jby}$. Because it was affected by not only the yield penetration of steel bar but also the axial elongation in the plastic hinge.

• Journal of Sensor Science and Technology
• /
• v.9 no.2
• /
• pp.120-126
• /
• 2000

This paper dealt with the developed portable electric field meter which consisted of planar-type sensor, analog amplifier with gain controller, A/D convertor, and display unit. The principle of the planar-type sensor for detecting time-varying electric field of extremely low frequency (ELF) bandwidth was described, and a calibration system using cylindrical guard electrodes and parallel-plate electrodes was proposed. From the calibration experiment, the frequency bandwidth and the sensitivity of the developed electric field meter was $17[Hz]{\sim}7[kHz]$, and 4.45[mV/V/m], respectively. Also it can measure the electric field strength up to 10[kV/m], and the measured result was displayed on the liquid crystal display in digit. The electric field meter can be widely applied to measure electric field strength radiated from power lines, computers, and home appliances such as hair dryer, heater, etc.

• Journal of Sensor Science and Technology
• /
• v.9 no.4
• /
• pp.288-296
• /
• 2000

Thin-film chromel-alumel multijunction thermal converters with a low output resistance of $64{\sim}85\;{\Omega}$ showed approximately the square law-dependent input-output relation. The voltage responsivities were very low with $0.34{\sim}0.67\;V/W$ in air and $1.15{\sim}1.48\;V/W$ in vacuum, respectively, and the ac-dc voltage transfer error was very large with about +340 ppm in the frequency range of $40\;Hz{\sim}10\;kHz$ in the case of 1 V-input sinewave rms voltage. It can be concluded that the large transfer error of the thermal converter was mainly caused by the low voltage responsivity and the large heat loss due to low output resistance, which implies that the optimization for small ac-dc transfer error is required.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.424-424
• /
• 2012

ZnO는 수열합성법을 통해 저온에서 단결정으로 성장할 수 있기 때문에 광전소자 및 압전소자로 응용되고 있으나, 성장된 ZnO nanowire 내부 산소 결함 및 표면에 OH기의 흡착에 의해 소자특성 저하를 발생시킨다. 본 연구에서는 ZnO의 결함의 최소화를 위해 Glass 기판에 수열합성법으로 성장된 ZnO nanowire를 ICP 플라즈마 장치를 이용하여 O2 25 sccm, Base Pressure $1.5{{\times}}10^{-3}$ Torr을 기준으로 파워와 시간에 따라 표면처리 하였다. 플라즈마 처리된 ZnO nanowire의 결함특성과 형상을 XPS와 FE-SEM를 통하여 분석하였으며, ZnO nanowire의 소자특성을 평가를 위해 Kapton Film/AZO/ZnO nanowire/PMMA/Au 구조의 발전기를 제작하였다. 150 W, 10 min에서 532.4 eV의 -OH결합이 최소화됨을 확인하였으며, 이를 이용하여 Flexible ZnO nanowire 발전기 제작 했을 경우 최대 Voltage 5 V, Current 156 nA 전기적 특성을 확인하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1071-1076
• /
• 2008

This paper presents the self power generation from vibration using the piezoelectric bimorph actuator. The piezoelectric bimorph actuator was well developed with PZT-PNN-Fe piezoelectric ceramics. As the applied voltage was increased, a linear change of displacement was obtained with a relatively high ratio of 12.53 um/V for the bimorph actuator. Moreover, when the motor's rotational speed was 2000 rpm, the bimorph actuator, which has a resonance frequency of 68 Hz, exhibited the most efficient generation voltage of 10.4 V. This bimorph actuator could make the LED, emitting 60 mW, working successfully. Therefore, it is anticipated that the bimorph actuator will be useful as a power source for the next-generation electronic devices.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.9-12
• /
• 1993

This study investigated the propriety and the extension of the term of validity about the using watthour meters at present. The subject of study is 1Cent 2W 220V 30(10)A, 1Cent 3W 110V 30(10)A of model III watthour meters. They are the used metes(products in 1984) and the repaired meters(products in 1977) in the end of the period. The investigation is as follows. o Investigation of external appearance o Driving current test o Creeping test o Noise test o Error test o Durability test. Results of the study have been the number of 13.3% exceeded permitting error and the number of 31.3% failed in endurable test of 500 hours. So, the using meters are not suitable to extend the term of validity without the improvement of several characteristics.

• Journal of electromagnetic engineering and science
• /
• v.9 no.2
• /
• pp.53-60
• /
• 2009

Remarkable developments in the electric and electronic industry have given people's daily life much more convenience and abundance. However, in electrical communication, or electric and electronic fields, making electrical and electronic devices more functional, more integrated, and faster have put electromagnetic interference(EMI) into more complex forms, and lots of problems such as interruption, malfunction, or interference by noise between electrical communication systems occurs every day. In this research, the electromagnetic compatibility(EMC) filter in the high powered breaker was designed and fabricated as a counter measure. The filter attenuated noise more than 20${\sim}$50 dB in the range of 10 MHz${\sim}$1.5 GHz. And, when the electric fast transient(EFT) of 4 kV in the level 4 of IEC 61000-4-4 was induced, it was soon suppressed to 600 V.

• Journal of Sensor Science and Technology
• /
• v.19 no.2
• /
• pp.137-141
• /
• 2010

In this paper, we fabricated silicon piezoresistive pressure sensor with dry etching technology which used Deep-RIE and etching delay technology which used SOI(silicon-on-insulator) wafer. We improved pressure sensor offset and its temperature dependence by removing oxidation layer of SOI wafer which was used for dry etching delay layer. Sensitivity of the fabricated pressure sensor was about 0.56 mV/V${\cdot}$kPa at 10 kPa full-scale, and nonlinearity of the fabricated pressure sensor was less than 2 %F.S. The zero off-set change rate was less than 0.6 %F.S.

• Publications of The Korean Astronomical Society
• /
• v.19 no.1
• /
• pp.33-37
• /
• 2004

Through time-series CCD photometry using a 130mm refractor of Busan Science Academy, we found a new $\delta$ Scuti type variable star, esc 03665-00576. We performed following observations using a 1.8m telescope of Bohyunsan Optical Astronomy Observatory. Three frequencies have been derived by multiple-frequency analysis, which are 10.968, 7.156 and 15.182cycle $day^{-1}$, respectively. V-amplitude of esc 03665-00576 is ${\Delta}V$= 0.04.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1140-1140
• /
• 2015

In this paper, the MIM thin films were deposited on Si substrate by sputtering method. And MIM thin films were annealed at $400{\sim}600^{\circ}C$ using RTA. The capacitance density of MIM thin films were increased with the increase of annealing temperature. The maximum capacitance density of $0.62{\mu}F/cm^2$ was obtained by annealing temperature at $600^{\circ}C$. The voltage dependence of dielectric loss showed about 0.03 in voltage ranges of -10~+10 V.