• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.403-405
• /
• 2008

This paper proposes an output inductor-less active clamp forward converter employing current boost-up circuit for high power density adaptor. By applying the proposed current boost-up circuit, the proposed converter has low conduction loss and low voltage ringing of the secondary rectifier. This paper presents the analysis of the proposed converter and a comparison between the proposed converter and the conventional converter through experiment.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.251-253
• /
• 2006

This paper presents a start-up in-rush current reduction technique of asymmetry half-bridge DC/DC converter for PC power supply. The proposed converter is composed center-tapped half-bridge converter with blocking capacitor. The proposed converter can reduce the severe in-rush current when the proposed converter is power up. The validity of this study is confirmed from the experimental results.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1402-1412
• /
• 2017

This paper presents a new high step-up dc/dc converter for renewable energy systems in which a high voltage gain is provided by using a coupled inductor. The operation of the proposed converter is based on a charging capacitor with a single power switch in its structure. A passive clamp circuit composed of capacitors and diodes is employed in the proposed converter for lowering the voltage stress on the power switch as well as increasing the voltage gain of the converter. Since the voltage stress is low in the provided topology, a switch with a small ON-state resistance can be used. As a result, the losses are decreased and the efficiency is increased. The operating principle and steady-states analyses are discussed in detail. To confirm the viability and accurate performance of the proposed high step-up dc-dc converter, several simulation and experimental results obtained through PSCAD/EMTDC software and a built prototype are provided.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.5
• /
• pp.1120-1128
• /
• 2004

In this paper, we has designed and implemented Up-converter for K-band with high IMD3 performance using balanced power amplifier. It is consisted of PA module and, Local Oscillator module with reject Filter, mixer module and If block, and Up-converter has a local loop path to decide whether it operate or not and has the sensing port to inspect output power level. According to the power budget of designed Up-converter, K-band balanced power amplifier was fabricated by commercial MMIC. Measurement results of up-converter show about 40dB Gain, PldB of 29dBm and OIP3 was 38.25dBm, that is good performance compared to power budgets. We has adjusted gate voltage of MMIC to control more than 30 dB gain. This up-converter was used in transceiver for PTP and PTMP, and applied to digital communication system that use QAM and QPSK modulation.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2002.06a
• /
• pp.62-68
• /
• 2002

In this paper, we have developed the Up-Convertor for CATV Head/End using 54∼750 MHz. We have individually designed and fabricated the main circuit of Up-converter such as Amplifier, frequency mixer, Voltage Controlled Oscillator(OSC), and we have realized the implementation for System Module in each circuit, so we have achieved a small size, light weight. and we have focused to have a shielding technique in high frequency bandwidth.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.542-546
• /
• 2001

Converter slag has some compositional similarities to portland cement. But it has no hydration properties due to it's quite high concentrations of FeO(20-35%), MnO(4-6.5%). So it is needed to reduce the concentrations of iron and manganese of converter slag to use as cement additives by enhancing it's hydration properties. In this study, converter slag was modified it's composition by mixing of silica, alumina and quenched BF slag and reduced in induction furnace and quenched in running water. The hydraulic properties and structures of modified and quenched converter slag are significantly changed depend on the amount and kinds of additives. The addition of alumina up to 10% and BFQ slag up to 20% by weight on converter slag was effective to enhance the hydraulic properties of modified and quenched slag. The addition of reduced and quenched converter slag up to 20% by weight in replacement of portland cement in mixing of concrete mortar were shown higher compressive strength than 100% cement concrete mortar.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2005-2015
• /
• 2016

A high-step-up DC/DC converter for renewable energy systems is proposed. The proposed structure provides high voltage gain by using a coupled inductor without the need for high duty cycles and high turn ratios. The voltage gain is increased through capacitor-charging techniques. In the proposed converter, the energy of the leakage inductors of the coupled inductor is reused. This feature reduces the stress on the switch. Therefore, a switch with low ON-state resistance can be used in the proposed converter to reduce losses and increase efficiency. The main switch is placed in series with the source. Therefore, the converter can control the energy flow from the source to the load. The operating principle is discussed in detail, and a steady state analysis of the proposed converter is conducted. The performance of the proposed converter is verified by experimental results.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.579-589
• /
• 2017

In this study a new high step-up dc-dc converter is presented. The operation of the proposed converter is based on the capacitor switching and coupled inductor with a single active power switch in its structure. A passive voltage clamp circuit with two capacitors and two diodes is used in the proposed converter for elevating the converter's voltage gain with the recovered energy of the leakage inductor, and for lowering the voltage stress on the power switch. A switch with a low $R_{DS}$ (on) can be adopted to reduce conduction losses. In the generalized mode of the proposed converter, to reach a desired voltage gain, capacitor stages with parallel charge and series discharge techniques are extended from both sides of secondary side of the coupled inductor. The proposed converter has the ability to alleviate the reverse recovery problem of diodes with circuit parameters. The operating principle and steady-states analyses are discussed in detail. A 40W prototype of the proposed converter is implemented in the laboratory to verify its operation.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.590-600
• /
• 2017

This paper presents a ripple-free input current modified interleaved boost converter for high step-up applications. By integrating dual coupled inductors and voltage multiplier techniques, the proposed converter can reach a high step-up gain without an extremely high turn-ON period. In addition, a very small auxiliary inductor employed in series to the input dc source makes the input current ripple theoretically decreased to zero, which simplifies the design of the electromagnetic interference (EMI) filter. In addition, the voltage stresses on the semiconductor devices of the proposed converter are efficiently reduced, which makes high performance MOSFETs with low voltage rated and low resistance $r_{DS}$(ON) available to reduce the cost and conduction loss. The operating principles and steady-state analyses of the proposed converter are introduced in detail. Finally, a prototype circuit rated at 400W with a 42-50V input voltage and a 400V output voltage is built and tested to verify the effectiveness of theoretical analysis. Experimental results show that an efficiency of 95.3% can be achieved.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3079-3085
• /
• 2014

This paper suggests a power level controllable frequency up-converter which is designed and fabricated using both the filtering technology consisted with only passive devices and a multi-level digital attenuator. The suggested frequency up-converter simultaneously realizes the low power consumption and the low cost model. Because of the possibility for controlling power levels, it is possible to use the suggested frequency up-converter for wide spectral range. According to the experimental results, the average gain value of 0.75dB is obtained for the bandwidth of 160MHz at the center frequency of 1,200MHz. Especially, it is confirmed that the power level can be controlled from 10 to -21.5dBm through the digital attenuator.