• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 추계학술대회
• /
• pp.32-33
• /
• 2010

This paper describes a droop control method for the autonomous operation of DC distribution system using distributed generations and energy storage. The method suppress the circulating current, and each unit could be controlled autonomously without communication system. Detailed model of wind power generation, photo-voltaic generation, fuel-cell generation and battery was implemented with the user-defined model of PSCAD/EMTDC software that is coded with C-language. The simulation and experimental results confirms that the proposed DC distribution system make it feasible to provide power to the load stably and verify effectiveness of the proposed method.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권7호
• /
• pp.635-641
• /
• 2016

엔진과 전기추진장치를 혼합한 하이브리드 추진 장치를 구동하기 위해서는 셀 단위로 이루어진 수십 개의 리튬계열의 배터리가 들어 있는 팩들로 접속이 된 전원을 사용한다. 따라서 많은 량의 배터리 셀의 상태를 언제든지, 엄격하게 관리할 필요가 있다. 일반적으로 배터리 관리(Battery management system, BMS)는 셀 전압, 전류 및 온도 등의 데이터를 운전 중에 받아서 상태를 컴퓨터로 모니터링 한다. 배터리의 상태를 확인하기 위한 또 다른 중요한 데이터는 배터리의 잔존수명(State of charge, SOH)을 알 수 있는 내부저항과 충전상태(State of charge, SOC)를 알 수 있는 무 부하 단자전압(Open circuit voltage, OCV)이 있다. 그러나 연속운전 중에는 내부 손실저항과 캐패시턴스의 병렬 등가회로로 인하여 내부저항의 측정이 어렵다. 또한 대부분의 에너지저장시스템에는 전압, 전류, 온도 등의 데이터를 이용하여 BMS가 수행되고 있지만, 운전 중에 예기치 않게 배터리 셀의 고장이 발생하는 경우에는 구동 전원장치의 출력전압이 변동하고, 하이브리드 자동차 또는 선박의 추진이 어려울 수가 있다. 본 논문에서는 리튬인산철 배터리 팩을 이용한 하이브리드 선박용 직류전원장치를 대상으로 배터리 셀의 돌발고장 순간에도 직류전원장치의 일정전압을 유지하면서 내부저항의 추정이 가능하고, 정상운전 중에는 OCV의 추정이 가능한 고 안전 BMS를 구현하고자 한다.

• 한국소음진동공학회논문집
• /
• 제20권5호
• /
• pp.437-443
• /
• 2010

SAW device is widely used as band pass filters, chemical or physical sensors, and actuators. In this paper, we propose the capacitive gap measurement system with high precision using SAW device. The research process is mainly composed of theoretical and experimental part. In the theoretical part, equivalent circuit model was used to predict the SAW response by the change of load impedance. In the experimental part, commercialized capacitor was used to see the SAW response by the change of load capacitance to check the feasibility as a sensor unit. After that, experimental setup to measure and adjust the gap was made and the SAW response by the change of gap which caused the capacitance change was measured. Finally, resolution and stroke was decided compared with the signal change and basic measurement noise level.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1225-1227
• /
• 1992

This paper presents a study on the variable structure PI(proportional and integrate) control which is insensible to the variation of parameters or external disturbance for driving DC motor. In the presented variable structure PI control (VSPIC), the sliding mode control was used at the below of 4000 rpm and PI control also used at the above of 4000 rpm with no load. In other way, the PI control was used at the below of 4000 rpm and the sliding mode control at the above of 4000 rpm with some loading, and then the output waveform following the variation of load was measured. intel 8031 microcomputer unit and IBM PC was combined to form the full system and the speed control was performed with it. The experimental result of the fast response to speed was more improve than it was open loop state. For load varing, the sliding mode insensible to external disturbance was applied and the improved response was obtained.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.825-832
• /
• 2008

A simulation program is developed for analysing thermal networking process between the District heating and the CES(Community Energy Supply) systems. The effects of thermal networking on the District heating facilities previously being operated are implemented using mathematical correlations in terms of the fuel consumption and energy load such as heating and electricity. The operational characteristics according to the prime movers is modeled based on the materials of efficiency as a function of operational load. The unit energy load model is also developed extensively for several building types such as apartment complex, hotel, hospital, buildings for business and commercial use respectively. The specific features of the newly developed program in simulation of thermal networking process in district heating is described in terms of the reliability and the easiness for operating it etc.

• 조명전기설비학회논문지
• /
• 제28권6호
• /
• pp.40-44
• /
• 2014

In this paper, maximum power is the lowering device using the facility's energy use and peak load electricity through analyzing attitude should like to make it reduce its power base rate. Simulator to manage the demand for power, a maximum electric power base power from electronic watt-hour meters by a device's signal, predictive power, the current power by computing the goal of power for less than Maximum peak power and peak shift, so that you can manage, and peak York, which role you want a cut Metal heat treatment result which analyzes the data, demand for electricity company over the years of analyzing the characteristics of each load, and effects and Reducing power consumption device every month identified seven Sequence control to the load system and successful power control is about showing that the defined goals.

• 대한조선학회논문집
• /
• 제61권3호
• /
• pp.200-207
• /
• 2024

A multi-component force sensor has been developed to measure force and moment components in high-speed flow media for submerged models. The size of the test model is determined based on the Reynolds number of the model at the test speed and expected blockage effect. A two-component force sensor unit has been created by assembling pairs of column elements arranged symmetrically under an eccentric load. The six-component force sensor is constructed with symmetric arrangements of two-component force sensor units in a rectangular plane. The signals generated from the strain gauges attached to the surface of the elements can be converted into force signals. The performance of the waterproof six-component force sensor has been evaluated through calibration. A simplified interference decomposition procedure has been introduced to increase the accuracy of measurement.

• 한국강구조학회 논문집
• /
• 제29권6호
• /
• pp.435-442
• /
• 2017

모듈러 건축물을 중고층화하기 위해 횡력저항시스템은 반드시 필요한 구조 요소로 10~20층 규모에서 콘크리트 코어는 가장 전형적인 횡력저항시스템으로 알려져 있다. 습식 공법인 콘크리트 코어 공사는 모듈의 오염과 파손 가능성으로 모듈 적층과의 동시 작업이 곤란하다. 이에 모듈 적층과 콘크리트 코어의 동시 시공이 가능한 복합 PC 패널 공법을 개발하였다. 복합 PC 패널은 일정 간격을 두고 웨브가 마주보는 한 쌍의 C형강을 콘크리트 벽체의 상부와 하부에 결합한 구조 부재로 볼트로 접합하여 적층하는 건식 공법으로 콘크리트 코어를 구축할 수 있다. 이 연구에서는 복합 PC 패널이 콘크리트 벽체와 동등한 성능을 갖도록 해석을 통해 상세 개선 과정을 제시하였다.

• 한국산학기술학회논문지
• /
• 제18권2호
• /
• pp.672-680
• /
• 2017

태양광 발전 시스템은 태양광 패널이 부착되어 있는 구조물, 이를 지지하는 부분과 발전된 전력을 계통 또는 부하측에 공급하는 장치로 구성된다. 태양광 패널의 발전효율은 태양빛의 입사량에 영향을 받기 때문에 패널이 태양빛을 가장 많이 받을 수 있는 방향으로 패널 구조물을 설치한다. 그러나 태양은 계속 이동하기 때문에 고정식 보다는 태양을 향하여 패널이 회전하는 방식이 더욱 효율이 좋다. 태양광 패널 구조물은 야외에 설치되므로 풍하중, 적설하중 지진하중 등이 작용한다. 본 논문에서는 태양광 패널 구조물에 가장 영향이 큰 풍하중을 유한요소법을 사용하여 구하고 이를 적용하여 태양 추적식 발전 장치의 구조물을 설계하였다. 특히 패널간의 간격에 따른 풍하중을 구하고, 패널 구조물이 지면과 이루는 각도에 따른 풍하중의 변화도 구하였다. 패널간의 간격은 간격이 없을 경우, 간격이 40 mm, 80 mm일 경우 등 3가지 경우에 대하여 해석을 하였으며, 지면과의 각도는 30도, 45도, 60도 등에 대하여 해석을 하였다. 해석결과 풍하중은 패널간의 간격이 없을 경우가 가장 적게 나타났고, 지면과의 경사각이 클수록 커지는 것을 알 수 있었다.

• 한국산업융합학회 논문집
• /
• 제23권6_2호
• /
• pp.917-926
• /
• 2020

Friction mechanisms is a very important role in the industrial machinery. However, many experiments have been conducted to reduce the loss of energy resources and parts used due to friction because the friction force adversely affects parts, efficiency, noise, and the like of the power unit. Therefore, in this study, the friction coefficient according to the characteristics of the lubricant was measured to find out which Grease Lubricant maintains the low friction coefficient without being most affected by external conditions. A total of five grease lubricants were tested in this study: GHP CAL 301, GHP EP 2, GHP KG 10, GHP HPG 2, and GHP HTG 2. And the friction coefficient was conducted by changing the load conditions (2, 4, 6, 8, 10N) and rotational speed (24, 48, 67, 86, 105, 124, 143, 162vrpm) using a pin-on-disk wear test system. Also, duty number were calculated. As a result, it was confirmed that in all grease lubricants, the speed did not significantly affect the friction coefficient, and it was confirmed that in all lubricants, the size of the friction coefficient decreased as the load increased from a small load to a large load. In addition, it was determined from the experimental results that GHP EP 2 is the most suitable as a grease lubricant and GHP CAL 301 is not the most suitable.