• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.3
• /
• pp.157-165
• /
• 2000

A small hydraulic winch system with an automatic tension control unit was designed to improve the work efficiency of coastal small vessels and the dynamic response characteristics of the winch system operated in the open loop condition was investigated. The inlet and the outlet pressures in hydraulic motor, the torque and the rotating speed of winch drum were measured as a function of time, and the behaviour in autotension mode for stepped load changes was analyzed. The results obtained are summarized as follows : 1. The developed winch system for coastal small vessels will result in better fishing with improved efficiency and lower manpower consumption by remote control of winch system. 2. The rotating delay times of winch drum for on/off operations of solenoid valve were 0.09 see at CW mode and 0.04 sec at CCW mode, respectively. After the solenoid valve was controlled, response characteristics were unstable slightly but showed good tracking behaviour over short time. 3. The driving torque of winch system in autotension mode was kept almost constant of 55.9 kgf·m, and 11.1 then the rotating speed of winch drum was kept almost constant of 5.1 rpm in the larger torque than 55.9 kgf·m and 11.1 rpm in the lower torque than that. 4. The 5% settling times in the transient response characteristics of autotension mode under rapid increasing and decreasing conditions of load were 0.12 sec and 0.2 sec, respectively, and then the rotating speeds were 11 rpm and 5.3 rpm, respectively. 5. The tracking behaviour of torque and rotating speed by remote control operation were stable within 0.23 sec at CW mode and 0.37 sec at CCW mode, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.13-19
• /
• 2019

After the Fukushima nuclear accident, a new power supply using a lithium polymer battery has been proposed the first time in the world as the safety of the emergency battery facility has been required. It is required to have the safety of the rack system in which the battery device is installed in order to apply the proposed technology to the field. Therefore, the purpose of this study is to evaluate the seismic performance of string and rack frame for lithium-polymer battery devices developed for the first time in the world to satisfy 72 hours capacity. (1) The natural frequency of the unit rack system was 9 Hz, and the natural frequency before and after the earthquake load did not change. This means that the connection between members is secured against the design earthquake load. (2) he vibration reduction effect by string design was about 20%. (3) As a result of the seismic performance test under OBE and SSE conditions, the rack frame system was confirmed to be safe. Therefore, the proposed rack system can be applied to the nuclear power plant because the rack system has been verified structural safety to the required seismic forces.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.73-80
• /
• 2019

In this paper, the basic design of the electric hydraulic sliding deck system was developed to develop the electric hydraulic sliding deck which can easily upgrade the loading and unloading of the agricultural machinery by modifying the load of the existing 5ton cargo truck. Through the kinematic analysis, The length and structure of the specimens were designed and the materials were selected for safety and economical efficiency through structural analysis. For the basic design of the sliding deck system, we surveyed the agricultural machinery to be transported and selected necessary elements. And have devised a system using a hydraulic cylinder that can meet selected factors. Through the simplified modeling and kinematic diagram, the operating structure of the sliding deck system was grasped and the minimum length and structure of the sliding deck were devised, In order to select the sliding deck material satisfying, four representative materials used in the automobile structure were selected. Selected the parts to be analyzed and compared the stresses and deformation amounts according to the material under the conditions of maximum load through simplified modeling. As a result, SS41P material was used to reduce the unit cost and to achieve safety. The winch system was designed and applied for moving up and down of the farm machinery which can not be operated.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.3
• /
• pp.167-181
• /
• 2008

There are lack of labour and increase in logistics costs due to rapid change in logistics environments and the demand for logistics. The reality is that over spending on logistics costs are getting worse due to lack of logistics standardization. An example will be excessive logistics costs caused by unsatisfactory use of logistics equipments in wholesale markets. The logistics efficiency is falling due to delays in using logistics equipments and standardization. Therefore, there needs standardization of logistics functions and unit of handling in each stage from packing, unloading, storage, transporting, logistics information and needs logistics standardization on equipments, machineries used for the above. Standard unified with standardization is called specification and if standardization is applied broadly in manufacturing or processing, inspection than each process in terms of production can be managed rationally and labour skills will improve and product quality will be evenly maintained and compatability of each part in terms of assembly will be maintained thus materials and labour could be saved thus results in increasing productivity and lowering production costs. Also, if it is applied in industry at state-level then there will be rationalization in consumption in circulation as in purchase of raw materials, sales of products, purchase of products by consumers and contribute in improving compatibility and fair transactions. This paper is aimed to help in first solving factors affecting the most in improving logistic efficiency among unit load system and logistic hollowization, standardizing logistics base, standardizing logistics information. The study conducted surveys on limited companies but hope that in the future the target companies can be divided further into types, industries and conduct more demonstrative analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1131-1140
• /
• 2011

A new rotary gravure-offset printing unit is constructed by paralleling a gravure plate cylinder, a blanket cylinder and a impression roller. A Muti-Unit Gravure-Offset Printing Press(MUGOP) equipped with a series of the 3 printing units is utilized for roll-to-roll fine printing. Its core technology is precise over-piling printing of fine patterns. The severe problems of 'slurring' and 'doubling' in typical offset printing are unavoidable, which can be eliminated by applying a soft pad-type blanket cylinder and the unique 'true rolling' technique. Nip pressure between the blanket cylinder and the plate cylinder is measured by the constant pressure control system which equipped with load cells attached on the cylinders' axes. The running circumference of the blanket cylinder is increased to reach the same circumference of the plate cylinder as the pressure increasing, so that the specifications of the blanket cylinder is determined by the relationships of its shore hardness, diameter and nip pressure. When a softer blanket is used, a blanket cylinder of smaller diameter could give higher nip pressure. Realization of the true rolling technique on the MUGOP makes multilayer printing possible as well as fine printing in printed electronics.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.412-415
• /
• 2015

This paper presents a MPPT(Maximum Power Point Tracking) control CMOS interface circuit for vibration energy harvesting. The proposed circuit consists of an AC-DC converter, MPPT Controller, DC-DC boost converter and PMU(Power Management Unit). The AC-DC converter rectifies the AC signals from vibration devices(PZT). MPPT controller is employed to harvest the maximum power from the PZT and increase efficiency of overall system. The DC-DC boost converter generates a boosted and regulated output at a predefined level and provides energy to load using PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a schottky diode type DC-DC boost converter is used for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process. The chip area is $950um{\times}920um$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.6
• /
• pp.55-62
• /
• 2006

For the fault diagnosis of three-phase induction motors, we construct a experimental unit and then develop a diagnosis algorithm based on pattern recognition. The experimental unit consists of machinery module for induction motor drive and data acquisition module to obtain the fault signal. As the first step for diagnosis procedure, preprocessing is performed to make the acquired current simplified and normalized. To simplify the data, three-phase current is transformed into the magnitude of Concordia vector. As the next step, feature extraction is performed by kernel principal component analysis(KPCA) and linear discriminant analysis(LDA). Finally, we used the classifier based on radial basis function(RBF) network. To show the effectiveness, the proposed diagnostic system has been intensively tested with the various data acquired under different electrical and mechanical faults with varying load.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.132-137
• /
• 2004

On-Board Diagnostic(OBD) systems are in most cars and light trucks on the load today. During the 1970's and early 1980's manufacturers started using electronic means to control engine functions and diagnose engine problems. The CARB's diagnostic requirements to meet EPA emission standards have been designated as OBD with a goal of monitoring all of the emissions-related components, as well as the chassis, body, accessory devices and the diagnostic control network of the vehicle for proper operation. In this paper, we present a remote measurement system for the wireless monitoring of diagnosis signal and sensors output signals of ECU adopted KWP2000, united the OBD communication protocol, on OBD-compliant vehicle using the wirless communication technique of Bluetooth. In order to measure the ECU signals, the interface circuit is designed to communicate ECU and designed terminal wirelessly according to the ISO, SAE regulation of communication protocol standard. A microprocessor S3C3410X is used for communicating ECU signals. The embedded system's software is programmed to measure the ECU signals using the ARM compiler and ANCI C based on MicroC/OS kernel to communicate between bluetooth modules using bluetooth stack. The diagnostic system is developed using Visual C++ MFC and protocol stack of bluetooth for Windows environment. The self-diagnosis and sensor output signals of ECU is able to monitor using PC with bluetooth board connected in serial port of PC. The algorithms for measuring the ECU sensor output and self-diagnostic signals are verified to monitor ECU state. At the same time, the information to fix the vehicle's problem can be shown on the developed monitoring software. The possibility for remote measurement of self-diagnosis and sensor signals of ECU adopted KWP2000 in embedded system verified through the developed systems and algorithms.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1020-1022
• /
• 2001

because the output of solar cell is direct, it is necessary to install D/A converter system for A.C load, and in case of driving utility line system, it is possible to drive system relation when the system supplies sinusodal current ant voltage having unit power factor. As the characteristics of the soar cell output the is influenced by dailysunight charge, for more electric power it is essential to control the direction toward the san so that the driving point of solar cell can always operate near maximum output point. PWM modulation device among electric power converters must have stable modulation at anytime when it includes noise-factors such as noise-wave and noises on electric voltage wave, a synchronous signal system. In dealing with synchronous signal for control and control signal by microprocessor, it is necessary to compensate it because there is time difference between sample paint and carrier wave. On this papers, single phase PWM current type invertor controled the solar cell having typical voltage dropping character has optimun short current in short, reduces D.C reactance, composes controller for modulation and keeps lower harmonic and high power factor keeping maximum output of solar cell according daily sunlight charge variation.

• The Journal of Korean Institute for Practical Engineering Education
• /
• v.3 no.1
• /
• pp.143-148
• /
• 2011

In this study, the damage to the bridge structure such as the crack and water leakage was assessed due to the increase of the vehicle load and traffic on the roads. In order to make this into the database, as a part of the automation system development for the bridge maintenance, the students themselves designed and developed their own inspection robotic system based on the idea of robots currently being developed overseas. Its field testing was conducted and its applicability assessed. During the design and fabrication, its connection to the details of the unit course taken in the undergraduate level was focused. In terms of new product development, the field application was possible due to the support of the academic-industrial cooperation firms. Furthermore, through the survey of the students, the improvements in the practical skills of the students who participated in this development process was affirmed.