• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.40-48
• /
• 2001

An ultrasonic test method, as a nondestructive test is applied to ensure the clad interface quality assessment. According to the reference codes and standards, not only korea Industrial Standard(KS) but also American Society for Testing and Materials (ASTM) Standard, ultrasonic examination procedures use the pulse-echo, A-scan, back reflection signal drop method and/or side drilled reference hole used to establish the acceptance criteria of clad material test. But the variety of bonding materials and sizes makes it difficult to produce the reference blocks, or thus the criteria. In order to overcome these practical difficulties, new ultrasonic testing criterion is suggested. In this new method, the theoretical interface reflection signal amplitude level is calculated and suggested as an acceptance criteria with the back reflection signal set to 100% FSH(Full Screen Height) which is based on acoustic impedance mismatch at the clad interface for the explosive clad ultrasonic inspection. Applicability of suggested criterion, for the explosive clad Fe-Naval Brass with different bonding quality is confirmed to the pre-existed KS and ASTM specifications and verified by using SEM (Seanning Electron Microscope) micrograph. The results obtained by the suggested method is more conservative than the results according to the KS B 0234 and ASTM A 578 specifications The suggested method could be applicable to any other combination of explosive clad ultrasonic inspection.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.5
• /
• pp.80-85
• /
• 1997

Preventive diagnosis technique of power transforms is very important for highly reliable operation of power systems, and especially that of online transformer is needed in view of economy. Acoustic methods for partial discharge points have been studied abroad since 1960's in earnest. Electric-ultrasonic locating method by which partial discharges are found through detecting the electric and ultrasonic signal generated in partial discharge and ultrasonic-ultrasonic locating method by which partial discharges are found through detecting two ultrasonic signal with two ultrasonic sensor have been researched in our country. By using this ultrasonic-ultrasonic locating method, it was proposed of graphical determination technique of partial discharge points one dimension, two dimension, three dimension. But in locating partial discharges, they have assumed that the number of signal origin is one. So in this study we suggests a method of locating and knowing the number of signal origins when there are several origins by using ultrasonic-ultrasonic method.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.486-493
• /
• 2015

The ultrasonic nondestructive test (NDT) was applied to deck in-service to inspect and evaluate the performance of decking materials using ultrasonic pulse velocity. First, the measuring method between direct and indirect method according to transducer arrangement was studied. Second, the ultrasonic pulse velocity of decks in-service was compared with the passage of time. Finally, the change of ultrasonic pulse velocity was evaluated to expect service life of decking materials. The results of comparison between direct and indirect method was statistically insignificant and the ratio of direct to indirect method was 1.02. 1.05 respectively. The ultrasonic pulse velocity of decks in-service was decreased as the passage of time and the linear relationship in the ultrasonic pulse velocity to passage of time was found. From the results, The ultrasonic NDT will be helpful as an efficient method of on-site management of decks in-service.

• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.157-163
• /
• 2002

It is well recognized that the ultrasonic method is one of the most common and reliable nondestructive testing (NDT) methods for the quantitative estimation of defects in welded structures. However, NDT techniques applying for adhesively bonded joints have not been clearly established yet. In this paper, the detection of interface crack by the ultrasonic method was applied for the measurement of interfacial crack length in the adhesively bonded joints of double-cantilever beam (DCB). An optimal condition of transmission coefficients and experimental accuracy by the ultrasonic method in the adhesively bonded joints have been investigated and discussed. The experimental values are in good agreement with the computed results by boundary element method (BEM) and Ripling's equation.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.97-102
• /
• 2000

It is well recognized that the ultrasonic methods is one of the most common and reliable nondestructive testing(NDT) methods for the quantitative estimation of defects in welded structures. However, NDT techniques applying for adhesively bonded joints have not been clearly established yet. In this paper, the detection of interface crack by the ultrasonic method was applied for the measurement of interfacial crack length in the adhesively bonded joints of double-cantilever beam(DCB). The optimum condition of transmission coefficients in the adhesively bonded joints and it's experimental accuracy by the ultrasonic method have been investigated. The experimental values are in good agreement with the computed results by boundary element method(BEM) and Ripling's equation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1847-1853
• /
• 2000

A computer simulation technique for 2-dimensional laser generated ultrasonic waves was developed for visualization and investigation of ultrasonic propagation in solids. The technique is similar to a finite difference method (FDM) and a mass-particle model method, but uses a new nodal calculation method based on fundamental consideration of an elastic wave equation. By this method, the propagation behavior oflaser generated ultrasonic wave in thermoelastic and ablation mode is visualized and shows good agreement with previous experimental result or the numerical analysis result by Green function.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.818-823
• /
• 2013

In the process of sterilization during the manufacture of beverages, both the treatment time and the temperature influence the beverage taste and flavor. Therefore, to improve the beverage quality, a nonthermal sterilization method is preferred to a high-temperature one. A nonthermal method, ultrasonic treatment by shock waves from cavitation, has been known to have a sterilizing effect. In this study, to observe the effect of ultrasonic frequency and treatment time on beverage quality, batch type ultrasonic equipment was fabricated and tested. Further, to evaluate the applicability of this ultrasonic method to an in-situ process, flow type ultrasonic heptagonal equipment was fabricated and then used to perform a sterilization experiment. Subsequently, the sterilizing effect was measured under ultrasonic and low-temperature ($55^{\circ}C$) treatments. Based on the obtained results, ultrasonic sterilization technology that can be applied for treatments at flow rates of up to 3 L/min was developed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.411-414
• /
• 2000

An ultrasonic linear motor was composed of a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic oscillator which generates elliptical oscillations. Elliptical oscillations are generated by synthesizing two degenerated modes. Direction of vibratory displacement was analyzed by employing the finite element method. So, we could recognize that the direction of the slider's movement was controlled by changing the Phase difference of the drive voltage.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.10 no.1
• /
• pp.29-37
• /
• 1990

In this study the disbonding tests of adhesively bonded Al/Al honeycomb structures were performed by ultrasonic methods. Ultrasonic C-scan squiter method and ultrasonic surface wave attenuation measuring method were applied for the detection of skin/core disbonding. The bonding quality of Al/Al honeycomb structures could be well evaluated by properly controlled ultrasonic parameters.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.122-123
• /
• 2014

Measurement of the strength of concrete is an important indicator of the safety of the fresh as well as old concrete structures. It is possible to evaluate the strength of the concrete by means of an ultrasonic velocity method which is a kind of non-destructive inspection method for safety diagnostic evaluation of the building structures with aging. Steel embedded in the concrete and age of the concrete may affect ultrasonic pulse velocity. In order to accurately assess the strength of the concrete, it is necessary to understand rebar embedded in the concrete, steel shapes in various forms which effect ultrasonic pulse velocity. In this study, by measuring the velocity of ultrasonic waves generated when the waves pass through the ultrasonic pulse in a direction perpendicular to the reinforcing bars embedded in concrete, the effect of reinforcing bars on ultrasonic velocity accurately was verified and used to estimate the strength of the concrete.