• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.753-756
• /
• 1992

The piezoelectric ceramics of PMS-PZT was made in the radial mode disk. As the results, in the application of filter required conditions: that is, higher-values for piezoelectric properties($K_p$, $Q_m$) and lower-values for stabilities of $F_{\tau}$(temp. coefficient, aging rate), 5PMS-51PT-44PZ composition statified well. This composition was made in the dot-ring type. Asthe results, with increasing $n^2$ both $Q_m$ and S had high values, decreasing $n^2$ both $K_p$ and BW had low values when the diameter of sintered bodies were constant. Therefore, curve of filter characteristic have sharped with increasing $n^2$ and BW broadened with decreasing $n^2$.

• 한국광학회지
• /
• 제4권3호
• /
• pp.330-337
• /
• 1993

Erbium이 첨가된 광섬유를 이득 매질로 하여 광섬유 loop mirror가 포함된 '8' 자 형태의 고리형 광섬유 레이저를 구성하였다. Loop mirror내의 양방향으로 진행하는 두 광파간의 비선형적 위상차로 인하여 loop mirror의 투과율이 입사광 강도에 의존함으로써 수동형의 모드록킹이 가능하였으며, 외부 perturbation 이나 변조소자의 도움없이도 공진기내의 편광조절기만의 조절에 의해 모드록킹ㅇ르 시작시킬 수 있었다. 또한 모드록킹에 의한 펄스 출력 파형을 비선형 loop mirror의 투과특숭과 관련하여 고찰하여 보았다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.174-175
• /
• 2019

In this study, the spalling and ultrasonic pulse transmission time of concrete were investigated according to compressive strength during heating. As a result, the higher the compressive strength of the concrete, the more the explosion occurs, which affects the cross-sectional loss and the spalling fragment size. Also, ultrasonic pulse transmission time was found to be strongly influenced by the section loss of concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.224-225
• /
• 2017

Ultra-high-strength concrete exposed to high temperature is likely to cause spalling. Spalling is caused by the vapor pressure of the concrete, and the vapor pressure may be different depending on the heating conditions of the concrete. Therefore, in this study, a ring-type restrained specimen was fabricated using ultra-high-strength concrete and the vapor pressure generated in the concrete by heating condition(rapid and slow heating) was evaluated.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.40-46
• /
• 2001

An integrated analysis for the thermo-elastic deformation, fatigue, wear and brittle damage evolution of the shrink-fitted die with multi stress-ring of dissimilar materials is presented. A simple numerical algorithm for the moving elastic boundaries characterizing the contacts of the insert and multi stress-rings is presented. The initial stress distribution in the die due to shrink-fit is considered and the traction at the die surface contacting with the work piece is obtained by analyzing the elasto-plastic deformation of work piece. Elastic analysis of the separate-type die is performed and then the evolution of brittle damage, wear and fatigue life are predicted. This integrated analysis is applied to the extrusion die with two layers of stress-rings and the results are discussed in detail.

• 제어로봇시스템학회논문지
• /
• 제12권11호
• /
• pp.1065-1073
• /
• 2006

In this paper we confirm the relation between the phases and phase errors of the beat signal at the lock-in region of the amplitude modulation type ring laser gyroscope by numerical calculation. Based on this facts, we, numerically, study the envelopes and magnitudes of the dither noise for statistically summing out the beat signal phase error, and we, experimently, confirm these numerical results. As a result, we find that the dither noise requires the increase gradient and the decrease gradient of the dither amplitudes, and those gradients should be combined with white noise. The magnitude of the dither noise which is satisfied with these requirements should be more than 5 percents of the average dither amplitude.

• 대한수학회보
• /
• 제55권6호
• /
• pp.1627-1638
• /
• 2018

In this paper, we study an special type of cyclic codes called skew cyclic codes over the ring ${\mathbb{F}}_p+v{\mathbb{F}}_p+v^2{\mathbb{F}}_p$, where p is a prime number. This set of codes are the result of module (or ring) structure of the skew polynomial ring (${\mathbb{F}}_p+v{\mathbb{F}}_p+v^2{\mathbb{F}}_p$)[$x;{\theta}$] where $v^3=1$ and ${\theta}$ is an ${\mathbb{F}}_p$-automorphism such that ${\theta}(v)=v^2$. We show that when n is even, these codes are either principal or generated by two elements. The generator and parity check matrix are proposed. Some examples of linear codes with optimum Hamming distance are also provided.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.535-542
• /
• 2002

This paper show communication network scheme problem for the railway is solved which were electrical noise and line break in wayside using rerouting communication line, Considering the availability and the maintainability based on the reliability in design of communication networks. At first, Self-Healing Ring algorithm is suggested in that solution which is satisfied with above requirements. And also, in the advanced type, Dual Master scheme is suggested that the problem which is occurred in line break of both main and sub line at the same time can be solved using DMSHR(Dual Master Self Healing Ring). Therefore total reliability in railway system is going to be advanced using DMSHR scheme.

• Journal of applied mathematics & informatics
• /
• 제31권3_4호
• /
• pp.365-372
• /
• 2013

The essential aim of this paper is to define weighted $q$-Hardylittlewood-type maximal operator by means of $p$-adic $q$-invariant distribution on $\mathbb{Z}_p$. Moreover, we give some interesting properties concerning this type maximal operator.

• 박물관보존과학
• /
• 제16권
• /
• pp.56-81
• /
• 2015

족자 고리는 끈이나 유소를 고정시켜 걸 수 있도록 하는 장황 부속품으로 형태가 다양하며 여러 금속재를 사용하여 제작되었다. 현재 전통 형식의 고리는 대부분 개장으로 인해 유실되었으며, 일본식 고리를 사용하고 있다. 따라서 본 연구에서는 국립중앙박물관에 소장된 전통 족자 19점을 대상으로 고리의 형태와 제작기법, 성분을 조사하여 옛 형태를 복원해 보고자 하였다. 의궤 내용에서 고리는 원환(圓環), 국화동(菊花童), 배목(排目) 등 고유의 명칭으로 기록되어 있다. 휴대용 엑스선 형광분석기(portable X-ray fluorescence, Artax, Rontec)로 성분을 분석한 결과, 전통 형식의 고리는 황동, 철, 은-구리합금 등 다양한 금속재로 확인되었다. 구리와 아연이 주성분인 황동은 17점 족자 고리에 사용되었다. 전 윤시달 초상(신2339)의 배목에서는 철을 사용하였으며, 주석-납 합금으로 도금하였다. 이서구 초상(신1065)에서는 고리 전체가 은-구리합금으로 제작되었음을 확인하였다. 광학현미경(Leica, M205A)으로 제작 방법을 조사한 결과 원환은 금속봉을 절단한 뒤 둥글게 휘어 만든 유형과 주조로 제작된 유형으로 확인되었다. 배목은 주조한 합금으로 봉재나 판재를 만들고 다시 단조과정을 거쳐 제작하였고, 배목장식은 금속판재를 잘라 형태를 만든 후 축조와 타출기법 등으로 무늬를 새겨 장식하였다.