• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.753-756
• /
• 1992

The piezoelectric ceramics of PMS-PZT was made in the radial mode disk. As the results, in the application of filter required conditions: that is, higher-values for piezoelectric properties($K_p$, $Q_m$) and lower-values for stabilities of $F_{\tau}$(temp. coefficient, aging rate), 5PMS-51PT-44PZ composition statified well. This composition was made in the dot-ring type. Asthe results, with increasing $n^2$ both $Q_m$ and S had high values, decreasing $n^2$ both $K_p$ and BW had low values when the diameter of sintered bodies were constant. Therefore, curve of filter characteristic have sharped with increasing $n^2$ and BW broadened with decreasing $n^2$.

• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.330-337
• /
• 1993

Figure '8' type, passively-mode-locked erbium-doped-fiber ring laser was developed, incorporating a nonlinear loop mirror. Transmittance of the loop mirror was found to be dependent on the incident light intensity due to the non-reciprocal nonlinear phase shift, which enables the passive mode locking of the laser. Self-starting of stable mode locking was possible with only controlling the polarization controllers inside the cavity without any help of external perturbation or modulation. The mode-locked output pulse shape was discussed in relation with the transmission characteristics of nonlinear loop mirror.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.174-175
• /
• 2019

In this study, the spalling and ultrasonic pulse transmission time of concrete were investigated according to compressive strength during heating. As a result, the higher the compressive strength of the concrete, the more the explosion occurs, which affects the cross-sectional loss and the spalling fragment size. Also, ultrasonic pulse transmission time was found to be strongly influenced by the section loss of concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.224-225
• /
• 2017

Ultra-high-strength concrete exposed to high temperature is likely to cause spalling. Spalling is caused by the vapor pressure of the concrete, and the vapor pressure may be different depending on the heating conditions of the concrete. Therefore, in this study, a ring-type restrained specimen was fabricated using ultra-high-strength concrete and the vapor pressure generated in the concrete by heating condition(rapid and slow heating) was evaluated.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.40-46
• /
• 2001

An integrated analysis for the thermo-elastic deformation, fatigue, wear and brittle damage evolution of the shrink-fitted die with multi stress-ring of dissimilar materials is presented. A simple numerical algorithm for the moving elastic boundaries characterizing the contacts of the insert and multi stress-rings is presented. The initial stress distribution in the die due to shrink-fit is considered and the traction at the die surface contacting with the work piece is obtained by analyzing the elasto-plastic deformation of work piece. Elastic analysis of the separate-type die is performed and then the evolution of brittle damage, wear and fatigue life are predicted. This integrated analysis is applied to the extrusion die with two layers of stress-rings and the results are discussed in detail.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.11
• /
• pp.1065-1073
• /
• 2006

In this paper we confirm the relation between the phases and phase errors of the beat signal at the lock-in region of the amplitude modulation type ring laser gyroscope by numerical calculation. Based on this facts, we, numerically, study the envelopes and magnitudes of the dither noise for statistically summing out the beat signal phase error, and we, experimently, confirm these numerical results. As a result, we find that the dither noise requires the increase gradient and the decrease gradient of the dither amplitudes, and those gradients should be combined with white noise. The magnitude of the dither noise which is satisfied with these requirements should be more than 5 percents of the average dither amplitude.

• Bulletin of the Korean Mathematical Society
• /
• v.55 no.6
• /
• pp.1627-1638
• /
• 2018

In this paper, we study an special type of cyclic codes called skew cyclic codes over the ring ${\mathbb{F}}_p+v{\mathbb{F}}_p+v^2{\mathbb{F}}_p$, where p is a prime number. This set of codes are the result of module (or ring) structure of the skew polynomial ring (${\mathbb{F}}_p+v{\mathbb{F}}_p+v^2{\mathbb{F}}_p$)[$x;{\theta}$] where $v^3=1$ and ${\theta}$ is an ${\mathbb{F}}_p$-automorphism such that ${\theta}(v)=v^2$. We show that when n is even, these codes are either principal or generated by two elements. The generator and parity check matrix are proposed. Some examples of linear codes with optimum Hamming distance are also provided.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.535-542
• /
• 2002

This paper show communication network scheme problem for the railway is solved which were electrical noise and line break in wayside using rerouting communication line, Considering the availability and the maintainability based on the reliability in design of communication networks. At first, Self-Healing Ring algorithm is suggested in that solution which is satisfied with above requirements. And also, in the advanced type, Dual Master scheme is suggested that the problem which is occurred in line break of both main and sub line at the same time can be solved using DMSHR(Dual Master Self Healing Ring). Therefore total reliability in railway system is going to be advanced using DMSHR scheme.

• Journal of applied mathematics & informatics
• /
• v.31 no.3_4
• /
• pp.365-372
• /
• 2013

The essential aim of this paper is to define weighted $q$-Hardylittlewood-type maximal operator by means of $p$-adic $q$-invariant distribution on $\mathbb{Z}_p$. Moreover, we give some interesting properties concerning this type maximal operator.

• Conservation Science in Museum
• /
• v.16
• /
• pp.56-81
• /
• 2015

Ring in the scroll painting is one of the mounting elements which are fixed string and tassel to hang, these differ widely in shape and produce a variety of metals. Most traditional shapes of ring have been lost, because of remount, there are used Japanese style rings in present.Therefore, this study examines to shape, production technique and analyze component traditional style rings of 19 traditional scroll paintings in National Museum of Korea for restoration of original style. Ring has been recorded official names; Wonhwan(Ring), Gukhwadong(Chrysanthemum shaped ornaments), Baemok(Ring-shaped nail) in Uigwe. Result of an optical microscope (Leica, M205A), Wonhwan has two type of production technique; one is cutting and bending a metal rod and other is cast. Baemok is made to forging process after metal rod or plate by casting alloy. Baemok decoration is metal plate cutting shape, and then decorates it with pattern by using kicking line engraving, chasing and so on. Component analysis result from portable X-ray fluorescence found various metals, such as, brass, iron silver-cooper. Brass based on copper and zinc used rings of 17 scroll painting. Baemok of Yun Sidal portrait is used iron and plated with a tin-lead alloy. Yi Seogu portrait is silver-cooper alloy in whole ring.