• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3A
• /
• pp.189-197
• /
• 2009

In this study, truck weight data and load effects of single truck on bridges are analyzed for development of new vehicular load model of the reliability-based bridge design code. Rational load model and statistical properties of loads are important for developing reliability-based design code. In this study, truck weight data collected at four locations are used as well as data from four locations in other studies. Truck weight data are collected from WIM or BWIM system, which are known to give reliable data. Typical truck types, dimensions and axle weight distribution are determined. Probability distributions of upper 20% total truck weight are assumed as Extreme Type I and 100 years maximum truck weights are estimated by linear regression on the probability paper. The load effects of trucks having estimated maximum weights are analyzed for span length from 10 m to 200 m.

• International Journal of Highway Engineering
• /
• v.18 no.1
• /
• pp.1-11
• /
• 2016

PURPOSES : This study estimated the load effect of a single heavy truck to develop a live load model for the design and assessment of bridges located on an expressway with a limited truck entry weight. METHODS : The statistical estimation methods for the live load effect acting on a bridge by a heavy vehicle are reviewed, and applications using the actual measurement data for trucks traveling on an expressway are presented. The weight estimation of a single vehicle and its effect on a bridge are fundamental elements in the construction of a live load model. Two statistical estimation methods for the application of extrapolation in a probabilistic study and an additional estimation method that adopts the extreme value theory are reviewed. RESULTS : The proposed methods are applied to the traffic data measured on an expressway. All of the estimation methods yield similar results using the data measured when the weight limit has been relatively well observed because of the rigid enforcement of the weight regulation. On the other hand, when the estimations are made using overweight traffic data, the resulting values differ with the estimation method. CONCLUSIONS : The estimation methods based on the extreme distribution theory and the modified procedure presented in this paper can yield reasonable values for the maximum weight of a single truck, which can be applied in both the design and evaluation of a bridge on an expressway.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.228-232
• /
• 2002

This paper is reporting the whole process of developing a weight measuring scaler of truck and trailer system for static and dynamic condition. The sensors attached on the top of springs each wheels. Acquisition and data processing performs accurate data extraction from noise environment, filtering and estimation. Weight information was highly distorted with noise and perturbation. Hence the perturbation was classified several categories and evaluated for accurate signal extract. The final products supply accurate and easy readable data of load weight for truck. It supplies total weight as well as loading condition of each axle. It is expected that it give the information to the truck operator of proper amount loading and safe condition to drive with it.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.2 s.39
• /
• pp.223-232
• /
• 1999

For the design and maintenance of highways and road structures, the statistical data are needed for the vehicle, especially heavy truck crossing. So far, static weighing has been used but it needs fixed station, crews, and it takes a lot of time. Also truck mix and headway distances cannot be obtained. Bridge Weigh-In-Motion system uses the bridge as a weighing scale and collects the axle weights, axle distances. vehicle types and etc. without stopping or slowing down the vehicle. In this study, for the first time in the country, BWIM system is applied on steel I-girder bridge and its applicability is examined. Also data collected in this system is analyzed to get truck traffic characteristics including average daily truck traffic, weight distribution, typical truck configuration and overweight truck status. The results are compared with other data from weighing station and highway toll gates.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.187-196
• /
• 2010

The purpose of this study is to develop the calibration method for temperature effects to improve the accuracy of the Weigh-In-Motion(WIM) system for collecting long-term truck weight data. WIM system was installed at a location where the truck traffic volume is high and weight data has been collected from January 2010. In this study, as a calibration measure, the first axle weight of Truck Type 10, the semi tractor-trailer is used based on the fact that the first axle weight is relatively constant, independent of the cargo weight. From this fact, calibration equations are developed from the relationship between the axle weight and the temperature(daily mean, maximum and minimum). Analysis on calibrated weight data shows adequacy of the proposed calibration method. Results of this study can be used to improve the accuracy of the WIM system and to carry out more rational design of pavement and bridge structures.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.74-87
• /
• 2020

Overloaded trucks are the main source that threatens road safety and directly affects the reduction of pavement life. The On-board truck scale is the only equipment that could prevent overloading by measuring and adjusting the loading weight before driving. Legislation is needed to encourage its installation so that the driver can prevent overloading. In this study, an on-board truck scale system was installed on 30 dump trucks for transporting construction waste, such as soil and aggregates, which are major loads of 36.55% for overloading, and the trucks were monitored remotely. The overload prevention effect was analyzed by comparing driving data for 1 month before distribution of the weight display app that can recognize the weight to the driver and 1 month after distribution. After installation, overloading could be 6.1% reduced, and the transportation efficiency could be increased by checking the weight provided from the On-board truck scale system.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3A
• /
• pp.199-207
• /
• 2009

In this paper, new vehicular load model is developed for reliability-based bridge design code. Rational load model and statistical properties of loads are important for developing reliability-based design code. In the previous paper, truck weight data collected at eight locations using WIM or BWIM system are analyzed to calculate the maximum truck weights for specified bridge lifetime. Probability distributions of upper 20% total truck weight are assumed as Extreme Type I (Gumbel Distribution) and 100 years maximum weights are estimated by linear regression. In this study, effects of multiple presence of trucks are analyzed. Probability of multiple presence of trucks are estimated and corresponding multiple truck weights are calculated using the same probability distribution function as in the previous paper. New vehicular live load model are proposed for span length from 10 m to 200 m. New model is compared with current Korean model and various load models of other countries.

• Journal of Industrial Technology
• /
• v.15
• /
• pp.83-91
• /
• 1995

This paper presents the design of a smart A/D conversion interface used for measuring the load of a truck. Since the load-cell sensor to be used is very sensitive for weight variation, the interface board must have the low-drift and the A/D conversion for accuracy. A new integrator and comparator has been developed to reduce the offset voltage and the drift current of operational amplifiers and has been adapted into the interface board. Also, a software algorithm has been developed to obtain the stable and accrurate A/D conversion. This software includes a RS-485 communication program to control the interface, which gives a capability of backing-up the calibration data and transferring control data. The test and evaluation of the designed interface has been shown as having the better performance compared to the other types of existing weighing systems and sensor instruments.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.2
• /
• pp.111-123
• /
• 2006

In the design of bridges, exact evaluation of traffic loading is very important for the safety and maintenance of bridges. In general, traffic loading is represented by live load (including impact load) and fatigue load. For exact evaluation of traffic loading, it is important to get reliable and comprehensive truck data including the traffic and weight information. It requires the development of Bridge Weigh-In-Motion (BWIM), which measures the truck weights without stopping the traffic. Objectives of the study is (1) to develop the BWIM system, (2) to verified the system in bridges in Highways.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.2
• /
• pp.211-221
• /
• 2007

A structural reliability analysis of fatigue truck model for fatigue failure of highway steel bridges was performed by applying the Miner's fatigue damage rule expressed as a function of various random variables affecting fatigue damage. Among the variables, the statistical parameters for equivalent moment, impact factor, and loadometer were obtained by analyzing recently measured domestic traffic data, whereas the parameters on fatigue strength, girder distribution factor, and headway factor of the measured data available in the literature were used. The effects of various fatigue truck models, fatigue life, ADTT, fatigue detail category, loadometer, and gross vehicle weight of fatigue truck on the reliability index of fatigue damage were analyzed. It is expected that the analytical results presented herein can be used as a basic background material in the calibration of both fatigue design truck and fatigue load factor of LRFD specification.