• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.158-161
• /
• 2006

Superstrate pin amorphous silicon thin-film (a-Si:H) solar cells are prepared on $SnO_2:F$ and ZnO:Al transparent conducting oxides (TCO) In order to see the effect of TCO/P-layers on a-Si:H solar cell operation. The solar cells prepared on textured ZnO:Al have higher open circuit voltage $V_{oc}$ than cells prepared on $SnO_2:F$. Presence of thin microcrystalline p-type silicon layer $({\mu}c-Si:H)$ between ZnO:Al and p a-SiC:H plays a major role by causing improvement in fill factor as well as $V_{oc}$, of a-Si:H solar cells prepared on ZnO:Al TCO. Without any treatment of pi interface, we could obtain high $V_{oc}$, of 994mv while keeping fill factor (72.7%) and short circuit current density $J_{sc}$ at the same level as for the cells on $SnO_2:F$ TCO. This high $V_{oc}$ value can be attributed to modification in the current transport in this region due to creation of a potential barrier.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.5
• /
• pp.216-219
• /
• 2016

$SnO_2$ single layer films (100 nm thick) and 2 nm thick Ni intermediated $SnO_2$ films were deposited on glass substrate by RF and DC magnetron sputtering without intentional substrate heating and then the influence of the Ni interlayer on the electrical and optical properties of the films were investigated. As deposited $SnO_2$ single layer films show the optical transmittance of 82.6% in the visible wavelength region and a resistivity of $6.6{ \times}10^{-3}{\Omega}cm$, while $SnO_2/Ni/SnO_2$ trilayer films show a lower resistivity of $2.7{ \times}10^{-3}{\Omega}cm$ and an optical transmittance of 76.3% in this study. Based on the figure of merit, it can be concluded that the intermediate Ni thin film effectively enhances the opto-electrical performance of $SnO_2$ films for use as transparent conducting oxides in flexible display applications.

• Journal of the Korean Vacuum Society
• /
• v.6 no.2
• /
• pp.114-121
• /
• 1997

The transparent conductiong thin films of tin oxides were prepared on pyrex glass substrates by the pulse laser deposition. In the atmospheres of vacuum, O2, and $Sn(CH_3)_4$ a polycrystalline $SnO_2$ target was ablated by Nd-YAG laser beam to deposit thin films on the substrates at room temperature, and as-deposited films were subsequently heat-treated in the air for 2 h at 230, 420 and $610^{\circ}C$, respectively. The characteristics of the thin films were examined by UV-VIS-NIR spectrometry and X-ray diffractometry, and the electrical properties were measured by four-point probe method along with film thickness monitored by the stylus method. It was observed that in the presence of $Sn(CH_3)_4$, $SnO_2$ phases were grown even at room temperature. This suggests that the microplasma producted during the laser ablation plays an important role in the dissociaation of precursor molecules.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.450-450
• /
• 2006

Organic light-emitting diodes (OLED) as pixels for flat panel displays are being actively pursued because of their relatively simple structure, high brightness, and self-emitting nature [1, 2]. The top-emitting diode structure is preferred because of their geometrical advantage allowing high pixel resolution [3]. To enhance the performance of TOLEDs, it is important to deposit transparent top cathode films, such as transparent conducting oxides (TCOs), which have high transparency as well as low resistance. In this work, we report on investigation of the characteristics of an indium tin oxide (ITO) cathode electrode, which was deposited on organic films by using a radio-frequency magnetron sputtering method, for use in top-emitting organic light emitting diodes (TOLED). The cathode electrode composed of a very thin layer of Mg-Ag and an overlaying ITO film. The Mg-Ag reduces the contact resistivity and plasma damage to the underlying organic layer during the ITO sputtering process. Transfer length method (TLM) patterns were defined by the standard shadow mask for measuring specific contact resistances. The spacing between the TLM pads varied from 30 to $75\;{\mu}m$. The electrical properties of ITO as a function of the deposition and annealing conditions were investigated. The surface roughness as a function of the plasma conditions was determined by Atomic Force Microscopes (AFM).

• Korean Journal of Optics and Photonics
• /
• v.13 no.5
• /
• pp.455-459
• /
• 2002

The transport and optical properties of $In_2O_3$:Zn(IZO) thin films grown by DC magnetron sputtering deposition have been studied. The deposition temperatures ($T_s$) were varied from room temperature to $400^{\circ}C$ in $50^{\circ}C$ steps. The IZO films are an amorphous phase for $T_s$<$300^{\circ}C$ and polycrystalline phase for $350^{\circ}C$＜$T_s$. In contrast to ordinary films, amorphous IZO films have lower resistivity and higher optical transmittance than polycrystalline IZO films. The resistivity of amorphous IZO was in the range of 0.29~0.4 m$\Omega$cm and that of polycrystalline IZO was in the range of 1~4 m$\Omega$cm. The carrier type for IZO film was found to be n-type, and the carrier density, was $3~5{\times}10^{20}/cm^3$. The Hall mobility, $({\mu}_H)$, was 20~$50\textrm{cm}^2$/V.sec. The predominant scattering mechanisms in both amorphous and polycrystalline IZO films were believed to be ionized impurity scattering and lattice scattering. The visible transmittance of the IZO films, which decreases with an increase of TS, was above 80%.

• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.3
• /
• pp.121-125
• /
• 2015

GZO single layer, Ni buffered GZO(GZO/Ni), Ni intermediated GZO (GZO/Ni/GZO) and Ni capped GZO (Ni/GZO) films were prepared on poly-carbonate (PC) substrates by RF and DC magnetron sputtering without intentional substrate heating and then the influence of the Ni (2 nm thick) thin film on the optical, electrical and structural properties of GZO films were investigated. As deposited GZO single layer films show the optical transmittance of 81.3% in the visible wavelength region and a resistivity of $1.0{\times}10^{-2}{\Omega}cm$, while GZO/Ni/GZO trilayer films show a lower resistivity of $6.4{\times}10^{-4}{\Omega}cm$ and an optical transmittance of 74.5% in this study. Based on the figure of merit, it can be concluded that the intermediated Ni thin film effectively enhances the opto-electrical performance of GZO films for use as transparent conducting oxides in flexible display applications.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.476-480
• /
• 2004

AZO (Al-doped ZnO) thin films were deposited on glass by pulsed magnetron sputtering method, and their structural, electrical and optical properties were investigated. XRD patterns showed that a highly c-axis preferred AZO film was grown in perpendicular to the substrate when pulse frequency of 30 ㎑ was applied to the target. Microstructure of thin films showed that the fibrous grain of tight dome shape was grown. The deposition rate decreased linearly with increase of pulse frequency, and the lowest resistivity was 8.67${\times}$10$\^$-4/ $\Omega$-cm for the film prepared at pulse frequency of 30 ㎑. The optical transmittance spectra of the films showed a very high transmittance of 85∼90%, within visible wavelength region and exhibited the absorption edge of about 350 nm. The characteristics of the low electrical resistivity and high optical transmittance of AXO films suggested a possibility for the application to transparent conducting oxides.

• Journal of the Korean Vacuum Society
• /
• v.22 no.5
• /
• pp.257-261
• /
• 2013

We have studied structural, optical, and electrical properties of the Al-doped ZnO (AZO) thin films using RF magnetron sputtering with various working pressure. To find optimal properties of AZO for transparent conducting oxides, the working pressure in sputtering process was varied as 0.07 Torr, 0.02 Torr, and 0.007 Torr, respectively. As working pressure increased, the crystallinity of AZO thin film was improved, the surface roughness of AZO thin film decreased. The transmittance of the film was over 80% in the visible light range regardless of the changes in working pressure. In case of 0.007 Torr, best electrical properties was shown due to the reduction of oxygen absorption by decreasing surface roughness.

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.491-496
• /
• 2011

Transparent conducting oxides (TCOs) used in the antireflection layer and current spreading layer of heterojunction solar cells should have excellent optical and electrical properties. Furthermore, TCOs need a high work function over 5.2 eV to prevent the effect of emitter band-bending caused by the difference in work function between emitter and TCOs. Sn-doped $In_2O_3$ (ITO) film is a highly promising material as a TCO due to its excellent optical and electrical properties. However, ITO films have a low work function of about 4.8 eV. This low work function of ITO films leads to deterioration of the conversion efficiency of solar cells. In this work, ITO films with various Zn contents of 0, 6.9, 12.7, 28.8, and 36.6 at.% were fabricated by a co-sputtering method using ITO and AZO targets at room temperature. The optical and electrical properties of Zn-doped ITO thin films were analyzed. Then, silicon heterojunction solar cells with these films were fabricated. The 12.7 at% Zn-doped ITO films show the highest hall mobility of 35.71 $cm^2$/Vsec. With increasing Zn content over 12.7, the hall mobility decreases. Although a small addition of Zn content increased the work function, further addition of Zn content over 12.7 at.% led to decreasing electrical properties because of the decrease in the carrier concentration and hall mobility. Silicon heterojunction solar cells with 12.7 at% Zn-doped ITO thin films showed the highest conversion efficiency of 15.8%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.99.2-99.2
• /
• 2011

Transparent conducting oxides (TCOs) supported on glass are widely used as substrates in PEC studies for photovoltaic hydrogen generation applications However, high sheet resistane ($10{\sim}15{\Omega}/cm^2$) and fragileness of glass-supported TCO substrates are the obstacles to produce the large area PEC cells. Such internal sheet resistance is detrimental to efficient collection of photogenerated majority charge carriers at the photoactive material and electrolyte interface. Moreover, these TCO substrates are very expensive and consume about 40~60% cost of the devices. Hence, a low sheet resistance of the substrate is a key point in improving the performance of PEC devices. Metallic substrates coated with a photoactive material would be a good choice for efficient charge collection. Such metal substrates based photanodes are best candidate for large-scale phtoelectrochemical water splitting for hydrogen generation. In this study, we report the enhanced PEC performance of $WO_3$ film on metal(chemical etched, bare) substrate. It is proposed that interface between $WO_3$ and the metal substrate is responsible for efficient charge transfer and demonstrated significant improvement in the photoelectrochmical performance. X-ray diffration and FESEM suduies reveled that $WO_3$ films are monoclinic, porous, polycrystalline with average grain size of ~50nm. Photocurrent of $WO_3$ prepared on metal substrates was measured in 0.5M $H_2SO_4$ electroyte under simulated $100mW/cm^2$ illumination.