• 대한기계학회논문집B
• /
• 제38권9호
• /
• pp.773-779
• /
• 2014

가스터빈 희박 예혼합 연소기에서 발생하는 연소 불안정 현상을 모델링하기 위해서는 화염의 동 특성에 대한 정량적, 정성적 분석이 필수적이다. 이를 위하여 화염전달함수가 전산유체역학을 통하여 모델링되었다. 기존 화염전달함수의 연구 결과로부터, 화염전달함수의 결과는 화염의 구조에 크게 의존하는 것으로 알려졌다. 본 연구에서는 실제 계측된 화염의 구조와 유사한 형상을 갖도록 열전달 조건을 최적화한 후, 동일 조건에서 화염전달함수가 모델링되었다. 화염의 형상을 정확하게 예측할 수 있다면, 이로부터 전달함수의 이득값과 위상차의 모델링 결과 역시 실험값과 유사한 거동을 확인할 수 있었다.

• 한국수자원학회논문집
• /
• 제31권6호
• /
• pp.741-755
• /
• 1998

인공배수 되고 있는 농업유역을 위한 확장된 TOPMODEL은 강우유출 모의를 위해 개발되어졌다. 불포화흐름의 해석을 위해 기존 모형의 저류함수법과 본 연구에서 새로이 제시하는 전달함수법을 비교하였다. 매개변수의 민감도 결정과 저류함수법과 전달함수법간의 거동의 비교를 위하여 영역화 민감도 분석기법이 쓰였다. Monte-Carlo 방법을 활용한 변수 추정시, 전달함수를 활용한 모의가 보다 많은 성공적인 모의결과의 변수조합이 관찰되었다. 강우유출 양상의 계절적 변동을 고려하기 위해 일곱 개의 강우사상이 만감도 분석에 활용되었다.

• 대한토목학회논문집
• /
• 제35권4호
• /
• pp.863-874
• /
• 2015

본 연구에서는 보강날개로 보강된 수중잠제 지지말뚝의 보강효과를 분석하기 위하여 하중전이거동을 분석하였다. 먼저 3차원 유한요소해석을 통해 말뚝의 변위 및 하중전이곡선(지반반력) 결과로부터 보강효과를 확인하고, 하중전이곡선에서 극한저항력 비율로 보강말뚝의 수평 및 인발하중에 대한 보강계수를 산정함으로써 보강효과를 정량화 하였다. 산정된 보강계수를 쌍곡선 하중전이함수의 극한저항력 $p_u$와 $t_{max}$에 곱해서 보정상수(fitting parameter)로 적용하여 보강효과를 고려한 하중전이함수를 제안하였다. 제안된 하중전이함수가 수치해석 결과를 잘 반영하고 있는지 확인하기 위해 3차원 유한요소해석을 비교하여 보강말뚝의 하중전이거동을 분석하였다. 제안된 하중전이함수를 하중전이법 해석에 적용하여, 실제 수중잠제를 해석한 결과 보강말뚝의 전단력, 휨 모멘트, 변위가 무보강말뚝보다 작게 발생하고, 지반반력은 더 크게 발생하여 비교적 경제적인 설계가 가능할 것으로 판단된다.

• 대한기계학회논문집A
• /
• 제24권8호
• /
• pp.1931-1939
• /
• 2000

Operating excitation forces of the linear vibratory system are normally determined by direct measurement techniques using load cells, strain gauges, etc. But, hydraulic forces of the rotating turbomachinery such as centrifugal pumps are exerted on an impeller due to asymmety of the flow by the interaction between pump impeller and volute. So, investigations of wide range of hydraulic designs and geometric deviations are difficult by direct method. This paper presents a hybrid approach for fourier transformed operational excitation forces, which uses pseudo-inverse matrix of the transfer matrix for the system and the measured vibrational data with standard installed pump. The determination of the transfer function matrix is based on a linear rotor/stationary system and steady state harmonic response in finite element analysis. And, vibrational data is collected in both vertical and horizontal directions at inboard and outboard bearing housings. The results of the process may be enhanced by making acceleration measurements at many more locations than there are forces to be determined.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.980-985
• /
• 2002

Several tests are performed to evaluate road booming noise. Baseline test delivers the information of road noise characteristics. Coupling effect between structure and acoustics is obtained from the mode shapes and the natural frequencies by the modal test. Equivalent stiffness at joint areas between chassis and car-body system can be determined by the input point inertance test. Noise sensitivity of body mounting point of a chassis part can be obtained from the noise transfer function test with input point inertance test. Operational deflection shape makes us analyze the actual vibration modes of the chassis system under actual loading and find noise sources very easily. finally, the transfer function analysis is used to identify noise paths through the chassis system. However, all of the tests above mentioned must be performed to evaluate road booming noise. The objectives and the procedures of the tests are described in this paper. Also, the guideline for efficient road noise evaluation test can be found.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2384-2389
• /
• 2007

The 2nd order response surface method (RSM) has been carried out to get optimum thermal design for enhanced heat transfer on square channel with bleed holes. The RSM was used as an optimization technique with Reynolds-averaged navier-stokes equation. Turbulence model for heat transfer analysis used RNG k-epsilon model. The wall function used enhanced wall function. Numerical local heat transfer coefficients were similar to the experimental tendency. Two design variables such as attack angle of rib (${\alpha}$), rib pitch-to-rib height ratio (p/e) were chosen. Operation condition considered bleeding ratio per bleed hole ($BR_{hole}$). A response surface were constructed by the design variables and operation condition. As a result, adjusted $R^2$ was more than 0.9. Optimization results of various objective function were similar to heat transfer in channel with and without bleed flow. But friction factor was lower than channel without bleed flow.

• Journal of Electrical Engineering and Technology
• /
• 제7권6호
• /
• pp.876-883
• /
• 2012

The paper investigates three types of transfer function methods for detecting displacements of winding in a model transformer. To acquire these transfer functions, the measuring method of input voltage, current and its response is used in impulse method. The applied impulse voltages had three rising times, which were short rising time (less than 0.6 ${\mu}s$), medium rising time (about 0.8 ${\mu}s$) and long rising time (about 1 ${\mu}s$) in front waves. Every 10 measurements of voltage and current waves were averaged from 50 measurements of voltage and current waves. These transfer functions were tested in normal, 24mm elevated and 48mm elevated windings conditions and were analyzed with correlation coefficients and spectrum deviations. In the analysis, the results depend on the types of transfer functions and the rising times of input voltages.

• 수산해양기술연구
• /
• 제29권1호
• /
• pp.39-55
• /
• 1993

Modal Analysis is the process of characterizing the dynamic properties of an elastic structure by identifying its modes of vibration. A mode of vibration is a global property of an elastic structure. That is, a mode has a specific natural frequency and damping factor which can be identified from response data at practically any point on a structure, and it has a characteristic mode shape which identifies the mode spatially over the entire structure. Modal testing is able to be performed on structural and mechanical structure in an effort to learn more about their elastic behavior. Once the dynamic properties of a structure are known its behavior can be predicted and therefore controlled or corrected. Resonant frequencies, damping factors and mode shape data can be used directly by a mechanical designer to pin point weak spots in a structure design, or this data can also be used to confirm or synthesize equations of motion for the elastic structure. These differential equations can be used to simulate structural response to know input forces and to examine the effects of pertubations in the distributed mass, stiffness and damping properties of the structure in more detail. In this paper the measurement of transfer functions in digital form, and the application of digital parameter identification techniques to identify modal parameters from the measured transfer function data are discussed. It is first shown that the transfer matrix, which is a complete dynamic model of an elastic plate structure can be written in terms of the structural modes of vibration. This special mathematical form allows one to identify the complete dynamics of the structure from a much reduced set of test data, and is the essence of the modal approach to identifying the dynamics of a structure. Finally, the application of transfer function models and identification techniques for obtaining modal parameters from the transfer function data are discussed. Characteristics on vibration response of elastic plate structure obtained from the dynamic analysis by Finite Element Method are compared with results of modal analysis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.1000-1004
• /
• 2008

As performance of medical air compressor improve, the problem of noise increased. Noise is very important to medical air compressor because most of this installed inside of building. The main goal of this paper is show TPA (Transfer Path Analysis) result for contribution analysis using PAK system. Generally, the conventional TPA method consists of two steps. First, transfer functions between output sound and sources are measured by excitation experiment. Second, transferred sound in each transfer path is generated by multiplying the transfer function and the sound source signal. Then, if the output sound synthesized from all transferred sounds doesn't give good agreement with the measured output sound (i.e., the accuracies of the transfer functions are low), setting a suitable countermeasure guideline becomes difficult. For obtaining highly accurate transfer functions, eliminating correlations among transfer functions and noise included in the measured data are necessary. In the new method with PAK system, the vibration acceleration and sound signals around the sound sources and the output sound were measured simultaneously to obtain the transfer functions when compressor was operating. By applying PAK system, a highly accurate and efficient transfer path analysis method was developed that does not require an excitation experiment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.138-142
• /
• 2001

A comparison between theoretical and measured transfer function, which relates structure-borne noise source level to underwater radiated noise, of a naval ship is presented in this study. Transfer functions are obtained by dividing far field underwater noise by the value of structure borne noise source levels below machinery mounts. In prediction, statistical energy analysis of the whole ship structure is used to get vibration levels of wetted hull plates below water line. Then, far field radiated noise is calculated by summing up contributions from each plates using vibration levels and radiation efficiencies. And 1/3-octave band underwater sound pressure at the distance of 1 m away from the hull were measured to get experimental transfer functions. The two transfer functions are compared to show resonable agreements in spite of the subtle physical differences between each other.