• Journal of Electrical Engineering and Technology
• /
• 제7권1호
• /
• pp.34-45
• /
• 2012

In the present paper, the mover speed control of a linear induction motor (LIM) using a sliding mode control design is proposed, considering the end effects. First, the indirect field-oriented control LIM is derived, considering the end effects. The sliding mode control design is then investigated to achieve speed- and flux-tracking under load thrust force disturbance. The numerical simulation results of the proposed scheme present good performances in comparison to that of the classical sliding mode control.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.292-295
• /
• 2003

In this paper, we present static output feedback model predictive tracking control for linear system with uncertainty. The proposed control law is based on integral action form to provide zero o��set for constant command signals and the closed loop stability is guaranteed under linear matrix inequality conditions on the terminal weighting matrix using the decreasing monotonicity property of the performance index. Through simulation examples, we illustrate that the proposed schemes can be appropriate tracking controllers for uncertain system.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.981-992
• /
• 2006

In this paper, a lateral vehicle control using the concept of control configured vehicle (CCV) is presented. The control objectives for the lateral dynamics of a vehicle include the ability to follow a chosen variable without significant motion change in other specified variables. The analysis techniques for decoupling of the aircraft motions are utilized to develop vehicle lateral control with advanced mode. Vehicle lateral dynamic is determined to have the steering input and control torque input. The additional vehicle modes are also defined to using CCV concept. We use right eigenstructure assignment techniques and command generator tracker to design a control law for an lateral vehicle dynamics. The desired eigenvectors are chosen to achieve the desired decoupling (i.e., lateral direction speed and yaw rate). The command generator tracker is used to ensure steady-state tracking of the driver's command. Finally, the developed design is utilized by using the lateral vehicle dynamic with four wheel.

• Journal of Power Electronics
• /
• 제9권2호
• /
• pp.320-333
• /
• 2009

A Photovoltaic (PV) system's power output varies with the change of climate. Frequency deviations, tie line voltage swings are caused by the varying PV power when large PV power from several PV systems is fed in the utility. In this paper, to overcome these problems, a simple coordinated control method for smoothing the variations of combined PV power from multiple PV systems is proposed. Here, output power command is formed in two steps: central and local. Fuzzy control is used to produce the central smoothing output power command considering insolation, variance of insolation and absolute average of frequency deviation. In local step, a simple coordination is kept between the central power command and the local power commands by producing a common tuning factor. Power converters are used to achieve the same output power as local command power employing PI control law for each of the PV generation systems. The proposed method is compared with the method where conventional Maximum Power Point Tracking (MPPT) control is used for each of the PV systems. Simulation results show that the proposed method is effective for smoothing the output power variations and feasible to reduce the frequency deviations of the power utility.

• 제어로봇시스템학회논문지
• /
• 제12권10호
• /
• pp.1002-1011
• /
• 2006

In this paper, a lateral vehicle control using the concept of control configured vehicle(CCV) is presented. The control objectives for the lateral dynamics of a vehicle include the ability to commend a chosen variable without significant motion change in other specified variables. The analysis techniques fur decoupling of the aircraft motions are utilized to develop vehicle lateral control with advanced mode. Vehicle lateral dynamic is determined to have the steering input and control torque input. The additional vehicle modes are also defined to using CCV concept. We use right eigenstructure assignment techniques and command generator tracker to design a control law for an lateral vehicle dynamics. The desired eigenvectors are chosen to achieve the desired decoupling(i.e., lateral direction speed and yaw rate). The command generator tracker is used to ensure steady-state tracking of the driver's command. Finally, the developed design is utilized by using the lateral vehicle dynamic with four wheel.

• 전력전자학회논문지
• /
• 제21권3호
• /
• pp.238-248
• /
• 2016

In this study, an automatic command mode transition strategy of direct power control (DPC) is proposed for permanent magnet synchronous generators (PMSGs) medium-voltage (MV) offshore wind turbines (WTs). Benchmarking against the control methods are performed based on a three-level neutral-point-clamped (NPC) back-to-back type voltage source converter (VSC). The ramping rate criterion of complex power is utilized to select the switching vector in DPC for a three-level NPC converter. With a grid command and an MPPT mode transition strategy, the proposed control method automatically controls the generated output power to satisfy a grid requirement from the hierarchical wind farm controller. The automatic command mode transition strategy of DPC is confirmed through PLECS simulations based on Matlab. The simulation result of the automatic mode transition strategy shows that the proposed control method of VOC and DPC achieves a much shorter transient time of generated output power than the conventional control methods of MPPT and VOC under a step response. The proposed control method helps provide a good dynamic performance for PMSGs MV offshore WTs, thereby generating high quality output power.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.65-70
• /
• 1989

Lately, at an epock of a full-scale satellite launching plan of Korea, T.T.C(Tracking, Telemetery & Command) is a indispensable part. In this paper, particular attention is given to orbit determination problem of the role of T.T.C. A near-earth satellite is modeled, batch and extended sequential estimation algorithm (ESEA) are compared using range data. As a result, ESEA show effectiveness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.137-139
• /
• 2007

In optical disk drives, a conventional control method in the presence of surface defect is holding the previous tracking control command. It is known that the method has a long settling time. This paper proposes a new control method which reduces the settling time. An optical head generally has coupled dynamics between focusing and tracking servo system. We present how to compensate the coupled dynamics so that reduced settling time is achieved. It is verified by experiments that the proposed method brings an improved performance in the presence of surface defect as well as in the normal operating condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2648-2653
• /
• 2003

This paper describes the development of a 3-DOF laparoscopic assistant robot system with motor-controlled bending and zooming mechanisms using the voice command motion control and auto-tracking control. The system is designed with two major criteria: safety and adaptability. To satisfy the safety criteria we designed the robot with optimized range of motion. For adaptability, the robot is designed with compact size to minimize interference with the staffs in the operating room. The required external motions were replaced by the bending mechanism within the abdomen using flexible laparoscope. The zooming of the robot is achieved through in and out motion at the port where the laparoscope is inserted. The robot is attachable to the bedside using a conventional laparoscope holder with multiple DOF joints and is compact enough for hand-carry. The voice-controlled command input and auto-tracking control is expected to enhance the overall performance of the system while reducing the control load imposed on the surgeon during a laparoscopic surgery. The proposed system is expected to have sufficient safety features and an easy-to-use interface to enhance the overall performance of current laparoscopy.

• 한국항행학회논문지
• /
• 제5권1호
• /
• pp.19-25
• /
• 2001

본 논문에서는 지면효과익기의 종운동 비행특성을 해석하고 비행제어 방식에 관한 비교연구를 한다. 먼저 비행 동특성을 해석하기 위해 지면효과익기가 지닌 것으로 알려진 비선형 특성을 제한 사이클을 통하여 살펴보고 또 선형화되었을 때의 특성과 연관하여 살펴본다. 또한 제어방식을 비교연구하기 위해 순항시에 고도오차가 있는 경우와 상승, 순항, 하강모드에 대한 명령추종관점에서 제어시스템의 성능 및 제어입력 실현 가능성을 비교한다. 제어입력으로는 승강타, 추력제어, 플랩 등의 조합을 고려하고 제어기법으로는 선형이차레귤레이터에 기반한 출력명령추종제어를 적용한다.