• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.117-124
• /
• 1993

This paper presents the study on the magnetic field analysis of magnetid deflection yoke using integral equation method. An integral equation method is developed for the computer modeling of the magnetic fields produced by color CRT and T.V. deflection yoke. Deflection of electron beams using magnetic fields is applied in a variety of display instruments such as te.evision receivers, electron probe instruments, etc. The magnetic field is solved by dividing these into the finite elements in the whole domain : the saddle coil which deflects the electron heam horizontally, the toroidal coil which deflects it vertically, magnetic core which enhances the magnetid fields genterated by the both coils. Using oblate spheroidal coordinates, this paper has had an easier access to the shape of magnetic deflection yoke chasing the boundaries than other coordinates.

• Journal of Powder Materials
• /
• v.13 no.4 s.57
• /
• pp.256-262
• /
• 2006

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy strip was pulverized to get a flake-shaped powder after annealing at $425^{\circ}C$ for 90 min and subsequently ground to obtain finer flake-shaped powder by using a ball mill. The powder was mixed with polyimide-based binder of $0.5{\sim}3wt%$, and then the mixture was cold compacted to make a toroidal powder core. After crystallization treatment for 1 hour at $380{\sim}600^{\circ}C$, the powder was transformed from amorphous to nanocrystalline with the grain size of $10{\sim}15nm$. Soft magnetic characteristics of the powder core was optimized at $550{\sim}600^{\circ}C$ with the insulating binder of 3wt%. As a result, the powder core showed the outstanding magnetic properties in terms of core loss and permeability, which were originated from the optimization of the grain size and distribution of the insulating binder.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.192-196
• /
• 2016

The Fe-Si-B-Nb-Cu alloys containing Ca and Al were rapidly solidified to thin ribbons by melt-spinning. The ribbons were ball-milled to make powders, and then mixed with 1 wt.% water glass and 1.5 wt.% lubricant. The mixed powders were burn-off, and then compacted to form toroidal-shaped cores, which were heat treated to crystallize the nano-grain structure and to remove residual stress of material. The characteristics of the powder cores were analyzed using a differential scanning calorimetry (DSC) and a B-H meter. The microstructures were observed using transmission electron microscope (TEM). The optimized soft magnetic properties (${\mu}_i$ and $P_{cv}$) of the powder cores were obtained from the Ca and Al containing alloys after annealing at $530^{\circ}C$ for 1 h. The core loss of Fe-Si-B-Nb-Cu-based powder cores was reduced by the addition of Ca element, and the initial permeability increased due to the addition of Al element.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.305-308
• /
• 2004

The 7-dial inductive voltage divider(IVD) for application at low frequency range which can precisely divide the in put voltage up to resolution of $10^{-7}$ was fabricated by using the toroidal cores made by super-mumetal strips of 0.025 mm thick and special decade switches. The cores have the initial permeability of 200.000 and magnetic flux density of 0.5 T. The inphase and quadrature ratio errors for a fabricated 7-dial IVD are found to be less than $\pm$4${\times}$$10^{-7}$ and $\pm$5${\times}$$10^{-6}$ rad(k=2), respectively. by calibration using the IVD calibration system of KRISS. The fabrication techniques used and uncertainty evaluation are discussed in this paper.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.6
• /
• pp.501-509
• /
• 1988

A new type toroidal core transformer for impedance matching for 30MHz~90MHz has been designed and fabricated. It is shown to be reasonably good characteristics that insertind loss was 1.2[dB], VSWR was 1:2.0 and 100[%] bandwidthe was achieved. It is expected that resulting transformer can be used to replace existing frequency selector type matching network because it is much more compact and relatively easy to contruct.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1037-1038
• /
• 2006

CFL(Compact Fluorescent Lamp)는 기존에 사용되던 백열 램프를 바로 대치할 수 있고, 백열 전구에 비하여 광 효율이 우수하다는 장점으로 인해서 사용처가 점점 증가되고 있는 추세이다. 하지만 등기구가 가지는 공간적인 제약으로 인해서 EMI 필터와 PFC 회로를 내장할 수 없으며, 램프에서 발생한 열이 직접적으로 안정기 회로에 영향을 주어 안정기 내부 온도가 매우 높게 상승한다는 점으로 인해서 다양한 기능을 갖는 전용 ballast control IC를 사용할 수 없었다. 이러한 이유로 인해서 toroidal core를 이용한 자려식(self-excited) 동작 방법이 주로 이용되어왔다. 이러한 자려식 발진 방법은 설계하기가 까다롭기 때문에 램프 점등 전에 램프 필라멘트를 예열한 이후에 점등을 하는 rapid start 방법을 구현하기 어려웠다. 본 논문은 fairchild 반도체에서 만든 CFL 전용 ballast IC가 가지는 특성에 대해서 다루었다. IC 내부에 안정기 동작을 제어하기 위한 제어 부분과 두 개의 MOSFET를 내장하고 있어 안정기 구성에 필요한 공간을 최소화할 수 있고, 부하 상태를 검출하여 항상 Active ZVS 동작을 하도록 하는 기능을 내장하고 있어서 스위칭 손실을 최소화할 수 있다는 장점을 가지고 있다.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1288-1289
• /
• 2006

Innovative SMC with low iron loss was made from iron powders with evaporated MgO insulation coating. The coating had greater heat-resistance than conventional phosphatic insulation coating, which enabled stress relieving annealing at higher temperature. Magnetic properties of toroidal samples (OD35mm,ID25mm, t5) were examined. The iron loss at 50Hz for Bm = 1.5T was lower 50% of conventional SMC and was almost the same with silicon iron laminations(t0.35). It became clear that MgO insulation coating has enough heat resistance and adhesiveness to powdersurface to obtain innovative SMC with low iron loss.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.209-214
• /
• 2016

This paper analyzes the magnetic property according to the machined shape of steel material with non-oriented silicon steel (50PN470/50A470), that is most commonly used in the design of electrical equipment. Toward this end, specimens were produced and divided into Bar-Specimen (Epstein Frame Tester) and Ring-Specimen (Toroidal Ring Tester). The characteristics of the electrical Silicon steel were measured using the instruments solely dedicated to measuring each specimen. The core loss of the Bar-Specimen, which is commonly used, was found to be less than that of the Ring-Specimen. This is a very important design factor in achieving the objectives of improving the product efficiency and predicting the performance of electrical equipment. It serves as a critical point of view in order to reduce the error between design value and product value. A comparative analysis was conducted regarding various characteristics (Hysteresis, B-H characteristic, Iron loss, Minor loop, Coercive force, Residual magnetic flux density, etc.) of the electrical silicon steel considered in the design of the electrical equipment according to the specimen.

• Journal of the Korean Magnetics Society
• /
• v.9 no.6
• /
• pp.278-284
• /
• 1999

The effect of TiO$_2$addition has been studied on the power loss, density, initial permeability, resistivity, and microstructure of Mn-Zn ferrites. TiO$_2$addition increased the density of sintered body and decreased of the initial permeability. Activation energy for electron hopping as well as electrical resistivity increased with TiO$_2$addition. The toroidal core sintered at 1150 $^{\circ}C$ with 1.5 wt% of TiO$_2$demonstrated the power loss of 83 mW/㎤ at 1 MHz, 25 mT, 8$0^{\circ}C$. However, the same specimen sintered at 120$0^{\circ}C$ lead to the power loss, 1168 mW/㎤ at 1 MHz, 25 mT, 8$0^{\circ}C$ and developed an exaggerated grain growth.

• Journal of the Korean Magnetics Society
• /
• v.25 no.1
• /
• pp.4-9
• /
• 2015

This study was carried out to investigate a influence of humidity variation (%) on the magnetic properties and the surface flaws in the fabrication of Fe-based $Fe_{78}Si_9B_{13}$ amorphous alloy ribbon by Planar Flow Casting process. As a result, the size of the air pocket and the droplet which is observed in the contact surface and the free face of the amorphous alloy ribbon becomes large when the humidity increases and the size highly increases with the surface roughness at the same time. Especially, the surface roughness value which is made in the 65 % of the humidity is the lowest in the contact surface ($Ra=0.60{\mu}m$, $Rz=3.11{\mu}m$) and the free face ($Ra=0.47{\mu}m$, $Rz=3.00{\mu}m$). Also, in case of the soft magnetic property of the magnetic core which is made with the toroidal core of $23(OD)^*20(ID)^*20(H)$ size, in the sample of the amorphous alloy ribbon which is made in 65% of the humidity, the most excellent value is gained as $B_s(B_{700})=1.055T$, $H_c=0.083Oe$, permeability = 1,197 and core loss = 0.276W/kg.