• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.34-41
• /
• 1997

The objective of this study is to investigate experimentally the frequency characteristics of the hole tones generated by a circular jet of low speed impinging on a plate with a round hole. The experimental results about the sound spectrum and the time wave of the hole tone are presented and discussed in relation with the hole type, the jet velocity and the distance of the nozzle-to-plate with a round hole. From the sound spectrum and time wave measurements, it is found that the hole tone is generated not only by an interaction of convected vortices with a round hole but also by a series of vortex shedding from jets passing through a hole. The hole tones generated by a feedback mechanism consist of many frequency stages and also have a hysteresis phenomenon like an edge tone. But the hole tones generated by a series of vortex shedding have nothing with the stage characteristics. The frequencies of hole tones are influenced by the jet velocity, the distance of the nozzle-to-plate with a round hole and the hole type.

• Journal of Information Display
• /
• 제13권3호
• /
• pp.131-137
• /
• 2012

In some previous studies, the effect of the microcapillary hole structure in the front dielectric layer was introduced. There have not yet been any report, however, on the detailed study on the discharge characteristics of the hole type, and on the optimization of the microscale hole size. In this study, the discharge characteristics of the microscale hole types in the front dielectric layer in plasma display panels were investigated through plasma numerical simulation. The numerical analysis discussed in this work may shed more light on the discharge mechanism. The modification of the structure of microscale holes is expected to improve the driving voltage and luminance, which may have been due to more energetically charged particles and Xe-excited species, which may in turn have been due to an expanded sheath electric field in the vicinity of the microholes.

• 마이크로전자및패키징학회지
• /
• 제22권4호
• /
• pp.71-76
• /
• 2015

최근 Light Emitting Diode (LED)의 효율을 높이기 위한 연구가 활발히 진행 되고 있다. 특히 소자 측면에서는 수평형 LED, 수직형 LED, via-hole 구조의 수직형 LED 등의 다양한 구조가 제시되었다. 본 논문에서는 시뮬레이션을 통해 via-hole 구조의 수직형 LED의 새로운 전극 디자인을 제시하였다. 기존 Via-hole 구조의 수직형 LED의 n-contact hole 주변에 전류가 밀집되는 문제점을 해결하면서 유효 발광면적을 극대화 시켜 소자 전체에 균일한 전류를 주입할 수 있는 소자 디자인에 대해 평가하였다. 시뮬레이션 결과를 바탕으로 최적의 전극 디자인을 실제 디바이스로 제작하여 기존의 via-hole 구조의 수직형 LED와 비교 분석하였다. 최적화된 디자인이 적용된 via hole type 수직형 LED의 경우 기존 디자인에 비해 350 mA 주입시 약 0.2 V의 Forward Voltage 감소하였지만 광 출력은 비슷하여 최종적으로 4.2%의 WPE (Wall plug efficiency)가 향상됨을 보였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.208-211
• /
• 2001

In the drawing from round billet to non-circular section there are two different processes through solid hole die(HD) and the other cassette roller dies(CRD). The CRD process has several cassette type rollers and a billet is able to move through the given gaps between two profiled rollers. The objective of this study is based on the analysis and evaluation of two aforementioned processes using experiments and finite element simulation. In order to simulate the multi-stage drawing process from circular sectioned billet to rounded square section, the finite element analysis is applied to the process using a commercially available DEFORM-3D code. Two types of experimental drawing tests through designed and manufactured dies for pure copper and aluminum alloy are carried out at room temperature. The analysis included comparison of material properties before and after drawing of each process and also provide some useful information by a FEM simulation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.208-213
• /
• 2004

The HANARO, multi-purpose research reactor, 30 MWth open-tank-in- pool type, is under normal operation since it reached the initial critical in February 1995. The HANARO is planning to produce a fission moly-99 of radio isotopes, a mother nuclide of Tc-99m, a medical isotope and is under developing a target handling tool for loading and unloading it in a circular flow tube (OR-5). A guide tube is extended from the reactor core to the top of the reactor chimney for easily un/loading a target under the reactor normal operation. But active coolant through the core can be quickly raised up to the top of the chimney through the guide tube by jet flow. This paper is described an analytical analysis to calculate the hole size of a orifice inserted in the circular irradiation hole and to study the flow characteristics through the guide tube under reactor normal operation and loading the target. As results, the results show that the hole size of orifice was 31 mm of the inner diameter to suppress the guide tube jet flow and the coolant safely cooled the target of fission moly after inserting the orifice to the flow tube.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.162-162
• /
• 2000

We describe a new optical-type guide sensor for AGV. It is robust the disturbance of the light. The developed optical-type guide sensor is very useful in the clean room environment where the light disturbance is very critical through the hole on the surface of the floor.

• Nuclear Engineering and Technology
• /
• 제54권10호
• /
• pp.3795-3802
• /
• 2022

NaI(Tl) scintillation materials are considered to be one of many materials that are used exclusively for γ-ray detection and spectroscopy. The gamma-ray spectrometer is not an easy-to-use device, and the accuracy of the numerical values must be carefully checked based on the rules of the calibration technique. Therefore, accurate information about the detection system and its effectiveness is of greater importance. The purpose of this study is to estimate, using an analytical-numerical formula (ANF), the purely geometric solid angle, geometric efficiency, and total efficiency of a cylindrical NaI(Tl) γ-ray detector with a side-through hole. This type of detector is ideal for scanning fuel rods and pipelines, as well as for performing radio-immunoassays. The study included the calculation of the complex solid angle, in combination with the use of various points like gamma sources, located axially and non-axially inside the through detector side hole, which can be applied in a hypothetical method for calibrating the facility. An extended γ-ray energy range, the detector, source dimensions, "source-to-detector" geometry inside the side-through hole, path lengths of γ-quanta photons crossing the facility, besides the photon average path length inside the detector medium itself, were studied and considered. This study is very important for an expanded future article where the radioactive point source can be replaced by a volume source located inside the side-trough hole of the detector, or by a radioactive pipeline passing through the well. The results provide a good and useful approach to a new generation of detectors that can be used for low-level radiation that needs to be measured efficiently.

• 한국정밀공학회지
• /
• 제25권3호
• /
• pp.126-133
• /
• 2008

The main objective of the present study is to achieve linear temperature distribution of cooling surface of plunger. K type thermocouples are attached at the surface of plunger to measure temperature. Nozzle and insulating material are inserted in the pin hole of the plunger for this study. Cooling water flow enters at one nozzle and leaves at three nozzles. Flow through nozzle can be activated in the pin hole, temperature of hot point around hole is decreased. Meanwhile, insulating material blocks off heat transfer, temperature of cold point around hole is increased. By combination of nozzle and insulation, heat transfer of hole is controlled effectively, as result its, temperature of plunger surface shows linear temperature distribution.

• 한국가시화정보학회지
• /
• 제9권3호
• /
• pp.38-43
• /
• 2011

When draining takes place through an axially located drain port in a cylindrical tank without any prevent, a vortex with an air core occurs. In this study, semi spherical concave and convex meshes with different size inner hole are used to find the air core can suppress. The study is carried out with different values of inner hole of mesh and different install direction of semi spherical mesh using PIV and measured velocity distribution. By providing a mesh, the air core can be prevented, even if the ratio of inner hole of mesh and diameter of cylinder is around 0.66. The experimental results show that a convex mesh type is more effective to suppress the air core generation than a concave mesh type.

• 센서학회지
• /
• 제18권3호
• /
• pp.239-244
• /
• 2009

We fabricated nano-templates by low temperature BCP(block copolymer) process at 180 $^{\circ}C$, then we deposited 10 nm-thick $TiO_2$ layers with ALD(atomic layer deposition) at low temperature of 150 $^{\circ}C$. Through FE-SEM analysis, we confirmed the successful formation of the groove-type(width of crest : 30 nm, width of trough : 18 nm) and the cylinder-type(diameter : 10 nm, distance between hole : 25 nm) templates. Moreover, after $TiO_2$-ALD processing, we confirmed the deposition of the uniform nano layers of $TiO_2$ on the nano-templates. Through AFM analysis, the pitches of the crest-through(in groove-type) and hole-hole(in cylinder-type) were the same before and after $TiO_2$-ALD processing. In addition, we indirectly determined the existence of the uniform $TiO_2$ layers on nano-templates as the surface roughness decreased drastically. We successfully fabricated nano-template at low temperature and confirmed that the three-dimensional nano-structure for sensor application could be achieved by $TiO_2$-ALD processing at extremely low temperature of 150 $^{\circ}C$.