• 동력기계공학회지
• /
• 제12권2호
• /
• pp.5-11
• /
• 2008

An analytical study was performed to have temperature and thermal stress distribution on a piston with the change of the 2nd land length of a piston and the existence of knocking in a cylinder. The result showed that the temperature on the skirt region was about $4\sim10^{\circ}C$ higher than that on the pin region. However the thermal stress on the skirt region was about 4MPa lower than on the pin region. It may be due to the higher heat release rate on the pin boss than on the skirt. The result regarding the variation of the 2nd land length of the piston showed that the temperature distribution on the piston was getting lower and the thermal stress distribution was getting higher as the 2nd land length of the piston was shorter.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.214-219
• /
• 2001

In this study, numerical investigation has been performed on the spreading and solidification of a droplet impacting onto a solid substrate in the thermal spray process. The finite difference method with volume-of-fluid approach is used to analyze the free surface flow and the source-based enthalpy method is employed to model the latent heat release during the solidification. In this work, the numerical model is validated through the comparison of the present numerical result with experimental data available for the flat substrate.

• Journal of Biosystems Engineering
• /
• 제27권1호
• /
• pp.39-44
• /
• 2002

In order to obtain the information of bio-environment control, the thermal characteristics of soil in the greenhouse heated by the heat pump and latent heat storage system were experimentally analyzed. The experimental systems were composed of the greenhouse with a heat pump and a latent heat storage system (system I), the greenhouse with a heat pump (system II), the greenhouse with a latent heat storage system (system III), and the greenhouse without auxiliary heating system (system IV). The thermal characteristics experimentally analyzed in each system were temperature of soil layers, soil heat storage and release, soil heat capacity and soil heat storage ratio. The results could be summarized as follows. 1. Time to reach the highest temperature at 20cm deep in soil layers of the crop routs in case of system I was shown to be delayed by 6 hours in comparison to the time of the highest temperature at the soil surface. 2. In the clear winter days, the stored heat capacity values fur the system I and the system II were shown to be 22.3% and 11.0% higher than the released heat capacity respectively, and the stored heat capacity values for the system III and the system IV were shown to be 6.2% and 29.6% lower than the released heat capacity respectively This confirms that the system I provided the best heat storage effect. j. The heat quantity values stored or released were shown to be highest at 5 cm depth of soil layers. And it was reduced with increasing of depth of soil layers until 20 cm and was not changed under the soil layer of 20 cm depth. 4. The heat absorption rates of soil, the ratio between supplied and stored heat energy, fur both the system I and system II were lower than 23%.

• 한국분말재료학회지
• /
• 제30권1호
• /
• pp.53-64
• /
• 2023

Atomic layer etching (ALE) is a promising technique with atomic-level thickness controllability and high selectivity based on self-limiting surface reactions. ALE is performed by sequential exposure of the film surface to reactants, which results in surface modification and release of volatile species. Among the various ALE methods, thermal ALE involves a thermally activated reaction by employing gas species to release the modified surface without using energetic species, such as accelerated ions and neutral beams. In this study, the basic principle and surface reaction mechanisms of thermal ALE?processes, including "fluorination-ligand exchange reaction", "conversion-etch reaction", "conversion-fluorination reaction", "oxidation-fluorination reaction", "oxidation-ligand exchange reaction", and "oxidation-conversion-fluorination reaction" are described. In addition, the reported thermal ALE processes for the removal of various oxides, metals, and nitrides are presented.

• 대한기계학회논문집A
• /
• 제21권10호
• /
• pp.1571-1579
• /
• 1997

The development of a new material which should be continuously use under severe environment of very high temperature has been urgently requested. For the development of such super-heat resistant materials, the main problem is not only to make the superior thermal barrier properties but also to actively release thermal stress. So, a new concept of functionally graded material(FGM) has been proposed to overcome this problem. A composition and microstructure of FGM are varied continuously from place to place in ways designed to provide it with the maximum function of mitigating the induced thermal stress. So, FGM can be applied in the aerospace, the electronic and the medical field, etc.. In this study, thermal stress analysis of sintering PSZ/NiCrAlY graded material was conducted theoretically using a finite-element program. The temperature condition was sintering temperature assuming a cooling-down process up to room temperature. Fracture damage mechanism was anlayzed by the parameters of residual stress. It could be known that FGM provided with the function of mitigating the induced thermal stress.

• 한국대기환경학회지
• /
• 제16권2호
• /
• pp.141-150
• /
• 2000

In order to genralize the vertical dispersion of plume at long distances on mesoscale over complex terrain dispersion coefficients data have been obtained systematically according to lapsed time after release by using a composite turbulence water tank that simulates convective boundary layer. Dispersion experiments have been carried out for various combined conditions of thermal turbulence intensity mechanical turbulence intensity and plume release height at slightly to moderately unstable conditions. Results of tracer dispersion experiments conducted using water tank camera and image processing system have been converted into atmospheric dispersion data through the application of similarity law. The equation $\sigma$z/Zi=aX/(b+c X2)0.5 where $\sigma$2; vertical dispersion coefficient zi : mixing height X : dimen-sionaless downwind distance was confirmed to be an appropriate and general equation for expressing $\sigma$2 variation with turbulence intensity and plume release height, The value of "a" was found to be principally affected by mechanical turbulence intensity and that of "b" by mechanical turbulence intensity and release height. It was confirmed that the magnitude of "c" varies with release height. Results of water tank experiments on the relationship of $\sigma$2 vs downwind distance x have been compared with actual atmospheric dispersion data such as CONDORS data and Bowne's nomogram Operating conditions of a composite turbulence water tank for simulating the field turbulence situations of CONDORS experiments and Bowne's $\sigma$2(x) nomogram for suburban area have also been investigated in terms of water temperature difference between convection water tank and bottom plate heating tank grid plate stroke mixing water depth length scale and velocity scale. Moreover the effect of mechanical turbulence intensity on vertical dispersion has been discussed in the light of release height and downwind distance. height and downwind distance.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.24-31
• /
• 2004

A cylindrical constant volume combustion bomb is used to investigate the combustion characteristics and to analyzer the heat quantity of inhomogeneous charge methane-air mixture. To analyze the heat quantity, some definitions including the CHR ratio, the UHC ratio and the HL ratio are needed and are calculated. It is shown that the effect of stratification is not significant in case of the overall excess air ratio of 1.1, mainly due to the higher heat loss and lower thermal efficiency compared to those of homogeneous condition. In the case of the overall excess air ratio of 1.4, as the initial charge pressure decreases, the CHR ratio has been decreased while the HL ratio has been increased, Generally, as the initial charge pressure increases, the amount of injection mixture has been decreased and has resulted in lower mean velocity and turbulence intensity for injection mixture. Also, the injected mixture is too rich to result in mixing deficiency in combustion chamber. From these results, it could be possible to acquire the improvement of thermal efficiency and the reduction of heat loss simultaneously through the 2-stage injection in CNG direct injection engine.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.83-91
• /
• 2000

A numerical study was carried out to investigate the 'unstart' process of thermally-choked combustion in model scramjet engines. The combustion mechanism of supersonic combustor will be compared with the experimental results obtained from the T3 free-piston shock tunnel at ANU (Australian National University) and the high enthalpy supersonic wind tunnel at UT (University of Tokyo). For the numerical simulation of supersonic combustion. multi-species Navier-Stokes equations were considered. and detailed chemistry reaction mechanism of $H_2$-Air were adopted. The governing equations were solved by Roe's FDS method and LU-SGS method with MUSCL scheme. In this study. it is found that the thermal choking process could result from excessive heat release due to combustion. In detail, sufficient heat release could be generated at local region of very high temperature increased by reflection of shock waves or vortex sheets. Accordingly the flow of downstream of the combustor fell to subsonic field propagated upstream along the combustor. Sometimes the subsonic flow field propagated into isolator could generate precombustion shock waves in the isolator.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.239-244
• /
• 2011

Nano Imprint Lithography(NIL) is technique for copying a pattern from stamp with nano size pattern in order to replicated the materials. It is very important to demold in order to make NIL process effectively. Self Assembled Monolayers(SAM) coater is manufactured by means of decreasing surface energy with the stamp surface treatment to improve release characteristics. Manufactured device contains tilting and rotation option for increasing process life time by coating on the sidewall of the pattern in stamp. The stamp coated with optimized tilting angle $30^{\circ}$ and rotation speed of 10rpm has more imprinting cycles than the stamping coated without tilting and rotation. Effective SAM coating on the sidewall of the pattern in stamp will improve by 50% of process life time.

• 한국연소학회지
• /
• 제21권2호
• /
• pp.29-37
• /
• 2016

This study described the experimental investigations of combustion instability in a model gas turbine combustor. Strong coupling between pressure oscillations and unsteady heat release excites a self-sustained acoustic wave, which results in a loud and annoyed sound, and may also lead to a structural damage to the combustion system. In this study, in order to examine the combustion instability phenomenon of a dual swirling combustor configuration, the information of heat release and pressure fluctuation period with respect to the variation in both thermal power and combustor length was collected experimentally. As a result, the fundamental acoustic frequency turned out to increase with the increasing thermal power without respect to the combustor length. The frequency response to the combustor length was found to have two distinct regimes. In a higher power regime the frequency significantly decreases with the combustor length, as it is expected from the resonance of gas column. However, in a lower power regime it is almost insensitive to the combustor length. This insensitive response might be a result of the beating phenomenon between the interacting pilot and main flames with different periods.