• Journal of Auto-vehicle Safety Association
• /
• v.10 no.3
• /
• pp.27-31
• /
• 2018

The People have a bad perception about diesel vehicle because of serious air pollution, increase fine dust and global vehicle company's diesel gate. Starting the project in 2005, Ministry of Environment has been supporting that is exhaust gas reduction devices (DPF) on diesel vehicles in the metropolitan area. During the period of 2017.01.01 to 2017.12.31, 10,030 diesel vehicles installed exhaust gas reduction devices (DPF). Among them, 9,921 diesel vehicles that they have sufficient data for analysis were analyzed amount of particulate matter reduction before and after exhaust gas reduction devices (DPF) was installed. Opacity smoke meter measures the concentration of particulate matter. So concentration of particulate matter was converted into a mass unit, and then calculated the total amount of reduced particulate matter. It was estimated that social benefits is costs required to remove it from the total amount of particulate matter.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.8
• /
• pp.74-81
• /
• 2019

Cars are inspected in the transport sector for their ability to achieve the greenhouse gas reduction targets. A vehicle (automobile) inspection broadly consists of regular and total checks, and both the safety level and the amount of exhaust gas are checked simultaneously during a vehicle inspection. This study deals with the efficiency of a soot probe to measure soot emissions from diesel vehicles. When the vehicle exhaust gas measurement is performed, there may be a difference between the exhaust gas temperature and the soot suction amount because of the different shape and angle of the exhaust port for each vehicle type. This may result in some incidents where the correct inspection nonconforming vehicle is not selected. Therefore, in this study, the shape of the probe was improved to increase the soot measurement efficiency under the condition of the exhaust pipe angle change.

• Management Science and Financial Engineering
• /
• v.3 no.1
• /
• pp.1-14
• /
• 1997

We address the problem of determining the sequence of a vehicle with fixed capacity to visit n nodes at which a predetermined amount is picked up and/or delivered. The objective is to minimize the total travel distance of the vehicle, while satisfying the pick-up/delivery requirements and feasibility at all nodes. Existing methods for the problem allows the vehicle to visit a node twice, which is impractical in many real situations. We propose a heuristic algorithm, in which every node is visited exactly once. Computational results using random problems indicate that the proposed heuristic outperforms existing methods for practical range of the number of nodes in reasonable computation time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.471-480
• /
• 2016

The purpose of this study is to identify the intent of the Total Amount of Vehicles policy that is enforced during the two summer season months (July and August) in U-do and the consequent problems after its implementation. We propose a basic direction for the policy to be sustainable. The average daily number of vehicles visiting was 645 in July 2015 and 953 in August 2015. As these numbers exceed the limit of 605, serious transportation problems such as traffic congestion and traffic accidents have occurred in U-do. We propose that the future direction of the policy is set forth as follows. First, mandatory reporting and the use of insurance, such as motorcycles, will have to be introduced along with measures to regulate violations. Second, a scheme needs to be introduced to enhance the total Amount of Vehicle policy and the number of inbound vehicles. Finally, public transportation cooperatives that are directly managed by local residents need to be established and an Eco-friendly vehicles dissemination policy introduced.

• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.97-106
• /
• 2017

PURPOSES: This study aims to evaluate the effects of vehicle dynamic behaviors on ride quality. METHODS : Simulation and field test were conducted to analyze the behavior of a driving vehicle. The simulation program CarSIM was applied and an INS (Inertial Navigation System) was used for field experiments. A small simulator was developed to simulate vehicle behavior such as roll, pitch, and bounce. The panels evaluated the ride quality in five stages from "very satisfied"to "very dissatisfied."Experiments were conducted on a total of 144 cases of vehicle behavior combinations. RESULTS :In both simulation and field tests, pitch is the largest and yaw the smallest. Especially in the field test, the amount of yaw is very low, about 7% of pitch and 18% of roll. The sensitive and extensive analysis conducted related ride quality with changing the frequency and amplitude. It was found that the most sensitive frequency range is 8 Hz across all amplitudes. Moreover, the combination of the roll and bounce was most sensitive to the ride quality at the low-frequency range. CONCLUSIONS : This result show that the vertical vehicle behavior (bounce) as well as the rotational behavior (roll and pitch) are highly correlated with ride quality. Therefore, it is expected that a more reasonable roughness index can be developed through a combination of vertical and rotational vehicle behavior.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2921-2927
• /
• 2011

Modal Shift from road to rail has been adapted in several countries as one of effective ways of reducing $CO_2$ emissions caused by transport. Generally, effect analysis of $CO_2$ reduction toward modal shift is calculated mainly from use stage and less consideration from other stages of life cycle, even though, in some case of modal shift needs that new line construction or new vehicle manufacturing. In this study, modal shift effect analysis is performed with considering construction, manufacturing vehicle and use stage. As a result we can get total $CO_2$ reduction effect using life cycle thinking and check the necessity of including other life cycle stage not only considering use stage. In conclusion, there is no $CO_2$ reduction effect if the reduction amount of $CO_2$ in use stage is not bigger than allocated annual amount of $CO_2$ in construction and manufacturing vehicle stage. According to this fact, analysing $CO_2$ reduction effect of Modal Shift should be considered not only the use stage.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.32-37
• /
• 2001

This article is to provide reasonably accurate vehicle emission estimates for the four sampled fuels which are commercially available across the nation. Emission quantities are obtained by testing a vehicle on a chassis dynamometer and capturing a sample of the emissions from the tailpipe in vehicle. The vehicle is driven following a particular pattern of idle, acceleration, cruise, and deceleration. Shown here is the trace of the test cycle known as the CVS-75 Mode which is used to certify the emission performance standards. The mode of CVS-75 consists of a cold start cycle, a hot stabilized cycle, and a hot start cycle. Emissions for the pollutants are measured in vehicle testing. These are carbon monoxide (CO), oxides of nitrogen (NOx), and total hydrocarbon (THC). The test results summarized in this report indicate that the differences for the amount of emission are quantitatively minimal.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.409-420
• /
• 2017

The amount of ventilation required in making the tunnel ventilation plan is an important factor for determining the capacity of the ventilation system. The amount of pollutant emission for each type of vehicle (basic emission amount for the design of ventilation volume) for estimating the required ventilation amount is based on the 'Standard for Allowing the Emission for the car manufacturing', proposed by Ministry of Environment. However, in 2013, the Ministry of Environment announced the 'Regulations on the calculation method of total emissions from vehicles' as a regulation for calculating the pollutants emitted from vehicles. In this regulation, there are the 'Emission factors for each type of vehicle'. Therefore, it is necessary to review the application of the Regulation to the estimation of the required ventilation volume for the road tunnel. In this study, the influence of the strengthened emission regulation in 2015 caused by the case of manipulation of emission volume for the diesel vehicle on the calculation of the required ventilation volume in the road tunnel has been checked. In addition, in this study, the required ventilation volume calculated according to the Standard for Allowing the Emission for the car manufacturing revised by Ministry of Environment and "Emission factors for each type of vehicle" and that calculated according to the EURO emission standard were compared for analysis. This study has implications that it provides the basic design data for calculating the reasonable ventilation capacity of the ventilation system based on the ground for calculating the required ventilation volume.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5D
• /
• pp.605-610
• /
• 2009

The either satisfaction levels or limits of tolerance levels felt by the users in the certain space/region should be examined for measuring social capacity on the total amount of vehicles. The reliability of measuring social carrying capacity depends primarily on decreasing the strategic responding biases. To induce the honest responses to preferences, Dichotomous Choice which is specifically known as the Double-Bounded Dichotomous Choice was adopted in this research to suggest the measurement methodology of social carrying capacity on the total amount of vehicles in U-do island. The empirical test was carried out the U-do island, an administrative district of Jeju Special Self-Governing Province. The number of vehicles satisfied by the 10% of residents was 390 and the satisfactory vehicle number was decreased to 132 extended to 90% of residents. This research, based on the political decision making criteria, set up the social carrying capacity in U-do island. The vehicle number satisfied by 50% of residents was 227, which meant the same number of residents turn to be supporter in case of political actions.

• Journal of Urban Science
• /
• v.11 no.2
• /
• pp.45-54
• /
• 2022

Recently, regulations on automobile exhaust gas emission are being strengthened. Accordingly, automobile exhaust gas emissions are expected to decrease and continue to decrease. On the other hand, many countries do not yet consider the emission of non-exhaust air pollutants from automobiles as important. Automobile non-exhaust substances are classified into three categories: tire dust emissions, brake wear emissions, and road scattering dust. In particular, in the case of tire dust, research results exist that pollutant emissions increase as the weight of a vehicle increases. Since the weight of trucks varies according to the load and the load along the axles is also different, it can be expected that the emission of PM10 from the tire dust will be different depending on the loading method. Therefore, this study was conducted on the amount of PM10 generated in tire dust considering the axle load of the truck according to the loading method. However, it was confirmed that the total amount of PM10 was less than that all loads are loaded in the front or rear when the load was evenly distributed in the front and rear of the cargo compartment. In particular, if the load is distributed evenly in the front and back of the cargo compartment and the load in the front part is divided into 2 to 6 and loaded, as the number of divided loading increases the amount of PM10 generated decreases. And when the load is divided into 6 pieces, the total amount of PM10 generated is 0.3952g, the minimum value. If the load is divided into 6 or more and loaded evenly, the total PM10 generated continuously increases and converges to about 0.3964g.