• 한국지반공학회논문집
• /
• 제20권6호
• /
• pp.51-59
• /
• 2004

공학적 물성치로서의 저변형율에서의 전단탄성계수의 결정은 다양한 토목분야에서 매우 중요하다. 본 논문에서는 저변형율에서의 전단탄성계수를 결정하기 위하여 개발된 HWAW(Harmonic Wavelet Analysis of Wave)방법을 이용한 지반조사기법의 실제 현장에서의 타당성을 검증하기 위하여 두 곳의 현장에 HWAW방법을 적용하였다. HWAW방법을 검증하기 위하여 동일한 현장에서 수행된 SASW시험과 PS-Suspension Logging 실험의 결과와 비교하였다. 이를 통하여 HWAW방법이 배경잡음과 지반의 횡방향 불균일성에 의한 오류를 기존 방법에 비하여 최소화 할 수 있으며, 국부적이며 정밀한 대상지반의 실제 전단파 속도 주상도를 매우 효과적으로 결정할 수 있음을 확인할 수 있었다.

• Nuclear Engineering and Technology
• /
• 제50권8호
• /
• pp.1298-1305
• /
• 2018

The use of System-on-Chip (SoC) solutions in the design of on-board data handling systems is an important step towards further miniaturization in space. However, the Total Ionizing Dose (TID) and Single Event Effects (SEE) characterization of these complex devices present new challenges that are either not fully addressed by current testing guidelines or may result in expensive, cumbersome test configurations. In this paper we report the test setups, procedures and results for TID testing of a SoC microcontroller both using standard $^{60}Co$ and low-energy protons beams. This paper specifically points out the differences in the test methodology and in the challenges between TID testing with proton beam and with the conventional gamma ray irradiation. New test setup and procedures are proposed which are capable of emulating typical mission conditions (clock, bias, software, reprogramming, etc.) while keeping the test setup as simple as possible at the same time.

• 천문학회보
• /
• 제43권1호
• /
• pp.68.3-68.3
• /
• 2018

The MATS (Mesosphere Airglow / Aerosol Tomography Spectroscopy) satellite is a Swedish scientific microsatellite which Kyung Hee University participates in developing. The limb telescope of the MATS satellite is designed with linear astigmatism-free off axis optical configuration which allows wide field of view ($5.67^{\circ}{\times}0.91^{\circ}$). Here we present the full-field optical performance test setup that consists of a point source, a collimator, the limb telescope and a CCD (Charged Coupled Device). The incidence angle of the collimator was carefully controlled by the rotary stage under the limb telescope. The imaging tests represent expected results without dominant aberrations.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권7호
• /
• pp.437-443
• /
• 2004

In this work the AC loss measurement setup based on an iron core background magnet, not used in a conventional one, has been successfully developed. To prove its validity, a round-robin test for the same Bi-2223 tape sample among three institutes has been done. The results show that the self-field and magnetization losses from the developed setup well agree with the losses measured at two other institutes of Korea Basic Science Institute and Yokohama National University. The measured magnetization losses for parallel or perpendicular fields can be well predicted from the slab model or the strip model for a filamentary region. However the magnetization losses for longitudinal fields can be rather predicted by the slab model for a decoupled filament. The self-field losses are well explained by the Norris ellipse model.

• 대한조선학회논문집
• /
• 제59권3호
• /
• pp.149-156
• /
• 2022

In order to study the open-water test and analysis techniques for pumpjet propulsors in the Large Cavitation Tunnel (LCT), at the Korea Research Institute of Ships and Ocean Engineering, a set of test equipment was designed and manufactured. The pumpjet propulsor is composed of rotor, stator and duct resulting in the strong interaction between the components. A ring-shaped sensor was developed to measure the thrust and torque for duct and stator. The test equipment including the pumpjet is installed on an existing POW dynamometer in the reverse direction. The results from the reverse POW test setup were validated against those from the conventional POW test setup in the Towing Tank (TT) as well as in the LCT. The pumpjet open-water test was conducted at the Reynolds number of around 1.0×106, at which the obtained experimental data became stable in the Reynolds number effect test. The open-water test for the rotor (rotor-only) was conducted to study whether the duct and stator should be considered as a part of the hull or the propulsor. On the basis of the test results, it was shown that the duct and stator could be included in the propulsor. The total thrust, combined thrust of rotor, duct, and stator was used for the pumpjet open-water test analysis. As the whole pumpjet is defined as a propulsor, it is thought that the self-propulsion test and analysis could be conducted in the same way as that of the conventional propeller.

• 한국의학물리학회지:의학물리
• /
• 제26권4호
• /
• pp.286-293
• /
• 2015

본 연구의 목적은 폐암의 정위체부방사선 치료 환자에 대하여 정위체부고정기구 사용 유무에 따른 셋업 정확성을 비교 평가하고자 한다. 본원에서 정위체부방사선치료를 받은 총 40명의 환자를 대상으로, 정위체부고정기구를 기반으로 한셋업 방식의 환자군 20명과 고정기구 없이 Wing board를 사용한 환자군 20명으로 구분하여 각 셋업오차를 비교, 분석 하였다. 폐암의 정위체부방사선치료는 총 4~5회에 걸쳐 48~60 Gy 조사되었다. 매 치료 전, 먼저 레이저를 이용하여 환자를 치료중심점에 위치시킨 후 On-board kV 영상장치를 이용하여 2차원 직각영상을 얻어 척추를 기준으로 환자의 위치를 조정한 다음, 3차원 체적 영상을 획득 하여 종양의 위치를 치료중심점에 일치시키고, 마지막으로 호흡에 의한 종양의 위치 확인 및 조정을 위해 2차원 직각 투시영상을 이용하였다. 각 과정에서 얻은 테이블 이동 및 회전 값을 조사하여, 셋업 군별로 계통오차 및 랜덤오차를 구하였다. 고정기구 사용유무에 따른 통계적 유의성을 검증하기 위하여 계통오차에 대한 t-test 시행을 하였고, 셋업의 재현성의 차이를 보기위해 랜덤오차에 대한 F-test를 시행하였다. 나아가 이러한 셋업 방식의 차이가 셋업 여유분의 크기 결정에 영향이 있는지 여부를 평가하기위해 치료계획체적의 여유분을 계산하여 두 방식의 차이를 비교하였다. 정위체부 고정기구를 사용했을 때의 셋업 오차는 수직방향, 길이방향, 수평방향으로 각각 $0.05{\pm}0.25cm$, $0.20{\pm}0.38cm$, $0.02{\pm}0.30cm$이었다. 반면에, Frameless immobilizer을 사용한 단순 고정방법을 사용했을 때의 셋업 오차는 수직방향에서만 통계적으로 유의하게 $-0.24{\pm}0.25cm$으로 증가함을 보였으나, 길이방향, 수평방향에 대해서는 각각 $0.06{\pm}0.34cm$, $-0.02{\pm}0.25cm$의 작거나 비슷한 결과값을 보였다. 정위체부 고정기구를 사용했을 경우, 수직방향, 수직방향 및 길이방향으로의 여유분은 각각, 0.67 cm, 0.99 cm, 0.83 cm였고, Frameless immobilizer시 수직방향으로 0.75 cm, 길이방향으로 0.96 cm, 수평방향으로 0.72 cm로써 수평방향에서 최대 0.11 cm 차이가 남을 알 수 있었다. 결론적으로 정위체부고정기구를 사용하는 것이 환자 자세 재현성을 향상시켜 셋업 오차를 환자의 전후, 위아래 방향으로의 약 0.1~0.2 cm씩 줄일 수 있을 것으로 평가하였다. 다만 정위체부 고정기구 사용에 따른 시간 소요 및 치료절차의 복잡성에 비해 그 효과는 그리 크지 않았다.

• Journal of electromagnetic engineering and science
• /
• 제13권1호
• /
• pp.54-61
• /
• 2013

An equivalent model has been developed to estimate the electromagnetic immunity for integrated circuits under a complex electromagnetic environment. The complete model is based on the characteristics of the equipment and physical configuration of the device under test (DUT) and describes the measurement setup as well as the target integrated circuits under test, the corresponding package, and a specially designed printed circuit board. The advantage of the proposed model is that it can be applied to a SPICE-like simulator and the immunity of the integrated circuits can be easily achieved without costly and time-consuming measurements. After simulation, measurements were performed to verify the accuracy of the equivalent model for immunity prediction. The improvement of measurement accuracy due to the added effect of a bi-directional coupler in the test setup is also addressed.

• Computers and Concrete
• /
• 제28권5호
• /
• pp.479-486
• /
• 2021

Reinforced concrete (RC) slabs are exposed to several static and dynamic effects during their period of service. Accordingly, there are many studies focused on the behavior of RC slabs under these effects in the literature. However, impact loading which can be more effective than other loads is not considered in the design phase of RC slabs. This study aims to investigate the dynamic behavior of two-way RC slabs under sudden impact loading. For this purpose, 3 different simply supported slab specimens are manufactured. These specimens are tested under impact loading by using the drop test setup and necessary measurement devices such as accelerometers, dynamic load cell, LVDT and data-logger. Mass and drop height of the hammer are taken constant during experimental study. It is seen that rigidity of the specimens effect experimental results. While acceleration values increase, displacement values decrease as the sizes of the specimens have bigger values. In the numerical part of the study, artificial neural networks (ANN) analysis is utilized. ANN analysis is used to model different physical dynamic processes depending upon the experimental variables. Maximum acceleration and displacement values are predicted by ANN analysis. Experimental and numerical values are compared and it is found out that proposed ANN model has yielded consistent results in the estimation of experimental values of the test specimens.

• Corrosion Science and Technology
• /
• 제23권2호
• /
• pp.145-153
• /
• 2024

In the automotive industry, the hole expanding test is widely used to assess the formability of punched holes in sheets. This test provides a good representation of formability within the framework defined by the ISO 16630 standard. During hole expanding tests on galvanized high strength steels, a negative effect was observed when there was a delay between hole punching and expansion, as compared to performing both operations directly. This effect is believed to be caused by hydrogen aging, which occurs when hydrogen diffuses towards highly-work hardened edges. Therefore, the aim of this study is to demonstrate the migration of hydrogen towards work-hardened edges in high strength Zn-coated steel sheets using a novel Thermal Desorption Analyzer (TDA) designed for small samples. This newly-developed TDA setup allows for the quantification of local diffusible hydrogen near cut edges. With its induction heating and ability to analyze Zn-coated samples while reducing artifacts, this setup offers flexible heat cycles. Through this method, a hydrogen gradient is observed over short distances in shear-cut galvanized steel sheets after a certain period of time following punching.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회 2006년도 추계학술대회
• /
• pp.127-133
• /
• 2006

Minimizing the total number of setup changes of a machine increases the throughput and improves the stability of a production process, and as a result enhances the product quality. In this context, we consider a new product-mix problem that minimizes the total number of setup changes while producing the required quantities of a product over a given planning horizon. For this problem, we develop a mixed integer programming model. Also, we develop an efficient heuristic algorithm to find a feasible solution of good quality within reasonable time bounds. Computational results show that the developed heuristic algorithm finds a feasible solution as good as the optimal solution in most test problems. Also, we developed a web based scheduling and monitoring system for a zinc alloy production process using the developed heuristic algorithm. By using this system, we could find a monthly zinc alloy production schedule that significantly reduces the total number of setup changes.