• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.336-344
• /
• 2011

The purpose of this study is to analyze the radiation-pattern characteristics above 1 GHz for the electromagnetic wave radiated from multi-slot such as ventilations, etc. on the enclosure of an EUT and so to make recommendations for suitable test methods. An experimental EUT was formed by putting a comb-generator at the center of a rectangular enclosure with 4 slots, and its radiation pattern was analyzed in the frequency range of 1~6 GHz. As analysis results, multi-lobe appears above 2 GHz and the number of multi-lobes is growing as the frequency increases. And real radiated-emission measurements were performed for the experimental EUT by scanning a receiving antenna in the height of 1~4 m and tilting toward maximum radiation, as well as setting the height of a receiving antenna to the central position of the EUT which is prescribed at the present standards. The measured results are +12.8 dB in the scanning and +16.4 in the scanning and tilting compared with the present standard test method. Therefore, the latter must be revised in order to consider the radiation pattern above 1 GHz.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.3
• /
• pp.7-13
• /
• 1997

To overcome the large hardware overhead attendant in the full scan design, the concept of partial scan design has emerged with the virtue of less area and testability close to full scan. Combinational Structure has been developed to avoid the use of sequential test generator. But the patterns sifted on scan register have to be held for sequential depth period upon the aid of the dedicated HOLD circuit. In this paper, a new levelized structure is introduced aiming to exclude the need of extra HOLD circuit. The time to stimulate each scan latch is uniquely determined on this structure, hence each test pattern can e applied by scan shifting and then pulsing a system clock like the full scan but with much les scan flip-flops. Experimental results show that some sequential circuits are levelized by just scanning self-loop flip-flops.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1383-1385
• /
• 2009

This paper suggests that testing method and equipment structure to detect potential failures of LCD cells. LCD Cell Aging Tester is the unique process to detect failures related with ASG circuits. This system consists of four components that is Aging chamber, work table, probe contact unit, and pattern generator. The key factor of the concept is temperature aging and HVS driving. Complicated combination of test parameters including voltage, temperature and frequency provided practical burn-in conditions eligible for prediction of mass production.

• The Journal of Korean Physical Therapy
• /
• v.17 no.1
• /
• pp.108-122
• /
• 2005

The gait training strategy in very important things for central nervous system(CNS) injury patients. There are many method and strategy for regaining of the gait who had CNS injury. A human being has central pattern generator(CPG) is spinal CPG for locomotion. It is a neural network which make the cyclical patterns and rhythmical activities for walking. Sensory input from loading and hip position is essential for CPG stimulation that makes the central neural rhythm and pattern generating structure. From sensory input, the proprioceptive information facilitate proximal muscles that controlled in voluntarily from cortical level and visual and / or acoustical information facilitate distal muscles that controlled voluntarily from subcortical level. Gait training method can classify that is functional level and structural level. Functional level includ level surface gait, going up and down the stair. It is important to facilitate a guide tempo in order to activate the central pattern generators. During the functional test or functional activities, can point out the poor period in gait that have to be facilitate in structural level. There are many access methods with patient position and potentiality. The methods are using of rhythmic initiation, replication and combination of isotonic with standing position. Clinically using it on weight transfer onto the stance leg, loading response, loading response and pre-swing, terminal stance, up and downwards stairs.

• Korean Journal of Digital Imaging in Medicine
• /
• v.11 no.2
• /
• pp.115-119
• /
• 2009

I think this will be valuable reference for assuring consistency and homogeneity of clarity and managing dental radiation equipment by experimentation of dental radiation equipment permanent which based on KS C IEC 61223-3-4 standard and KS C IEC 61223-2-7. Put a dental radiation generator and experiment equipment as source and film(sensor) length within 30 em, place the step-wedge above the film(sensor). Tie up tube voltage 60 kVp, tube current 7 mA and then get an each image through CCD sensor and film by changing the exposure time as 0.12sec, 0.25sec, 0.4sec. Repeat the test 5times as a same method. Measure the concentration of each stage of film image, which gained by experiment, using photometer. And the image that gained by CCD sensor, analyze the pixel value's change by using image J, which is analyzing image program provided by NIH(National Institutes of Health). In case of film, while 0.12sec and 0.25sec show regular rising pattern of density gap as exposure time's increase, 0.4sec shows low rather than 0.12sec and 0.25sec. In case of CCD sensor density test, the result shows opposite pattern of film. This makes me think that pixels of CCD's sensor can have 0~255 value but it becomes saturation if the value is over 255. The way that getting clear reception during decreasing human's exposed radiation is one of maintaining an equipment as a best condition. So we should keeping a dental radiation equipment's condition steadily through cyclic permanent test after factor examination. Even digital equipment doesn't maintain a permanent, it can maintain a clarity by post processing of image so that hard to set it as standard of permanent test. Therefore it would be more increase the accuracy that compare a film as standard image. Thus I consider it will be an important measurement to care for dental radiation equipment and warrant homogeneity, consistency of dental image's clarity through comparing pattern which is the result from factor test against cyclic permanent test.

• Analytical Science and Technology
• /
• v.34 no.2
• /
• pp.87-98
• /
• 2021

In this study, we developed the nanoparticle multi-generator by 3D printer fusion deposition modeling (FDM) method that can reliably generate and deliver nanoparticles at a constant concentration for inhalation risk assessment. A white ABS filament was used as the test material, and SMPS was used for concentration analysis such as particle size and particle distribution. In the case of particle size, the particle size was divided by 100 nm or less and 100 to 1,000 nm, and the number of particles concentration, mass concentration, median diameter of particles, geometric average particle diameter, etc were measured. The occurrence conditions were the extruder temperature, the extruding speed of the nozzle, and the air flow rate, and experiments were conducted according to the change of conditions including the manufacturer's standard conditions. In addition, the utility of inhalation risk assessment was reviewed through a stability maintenance experiment for 6 h. As a result of the experiment, the size of the nanoparticles increased as the discharger temperature increased, as the discharge speed of the nozzle increased, and as the air flow rate decreased. Also, a constant pattern was shown according to the conditions. Even when particles were generated for a long time (6 h), the concentration was kept constant without significant deviation. The distribution of the particles was approximately 80 % for particles of 60 nm to 260 nm, 1.7 % for 1 ㎛ or larger, 0.908 mg/㎥ for the mass concentration, 111 nm for MMAD and 2.10 for GSD. Most of the ABS particles were circular with a size of less than 10 nm, and these circular particles were aggregated to form a cluster of grape with a size of several tens to several hundred nm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.7 s.337
• /
• pp.37-44
• /
• 2005

This paper presents effective test patterns and their BIST implementations for SoC and Board interconnects. Initially '6n'algorithm, where 'n' is the total number of interconnect nets, is introduced to completely detect and diagnose both static and crosstalk faults. Then, more economic 4n+1 algorithm is described to perfectly capture the crosstalk faults for the interconnect nets separated within a certain distance. It will be shown that both algorithms can be easily implemented as interconnect BIST hardwares with small area penalty than conventional LFSR.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.343-346
• /
• 2009

Since an LFSR as a pattern generator has solely linear dependency in itself, it generates sequences by moving the bit positions for a pattern generation. So the correlation between the generated patterns is high and thus reduces the possibility of fault detection. To overcome these problems many researchers have studied to have goodness of randomness between the output test patterns. In this paper, we propose the new and effective method to construct phase shifter as PRPG.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.924-928
• /
• 2014

LLC resonant converter is used to control laser power density in ruby laser power supply. Zero voltage switching(ZVS) is implemented to minimize the switching loss by the LLC resonant converter. Laser output power is investigated and experimented by changing the output current. That current is controled by the charging voltage of capacitor. From those results, we obtained the maximum laser output of 1.94J at the discharge current of 860A and the pulse repetition rate of 1Hz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1186-1191
• /
• 2014

Weekly and monthly electric load forecasting are essential for the generator maintenance plan and the systematic operation of the electric power reserve. This paper proposes the weekly maximum electric load forecasting model for 104 weeks with the multiple regression model. Input variables of the multiple regression model are temperatures and GDP that are highly correlated with electric loads. The weekly variable is added as input variable to improve the accuracy of electric load forecasting. Test results show that the proposed algorithm improves the accuracy of electric load forecasting over the seasonal autoregressive integrated moving average model. We expect that the proposed algorithm can contribute to the systematic operation of the power system by improving the accuracy of the electric load forecasting.