• ETRI Journal
• /
• 제39권4호
• /
• pp.605-613
• /
• 2017

Simulated fault injection (SFI) is widely used to assess the effectiveness of fault tolerance mechanisms in safety-critical embedded systems (SCESs) because of its advantages such as controllability and observability. However, the long test time of SFI due to the large number of test cases and the complex simulation models of modern SCESs has been identified as a limiting factor. We present a method that can accelerate an SFI tool using a checkpoint forwarding (CF) technique. To evaluate the performance of CF-based SFI (CF-SFI), we have developed a CF mechanism using Verilog fault-injection tools and two systems under test (SUT): a single-core-based co-simulation model and a triple modular redundant co-simulation model. Both systems use the Verilog simulation model of the OpenRISC 1200 processor and can execute the embedded benchmarks from MiBench. We investigate the effectiveness of the CF mechanism and evaluate the two SUTs by measuring the test time as well as the failure rates. Compared to the SFI with no CF mechanism, the proposed CF-SFI approach reduces the test time of the two SUTs by 29%-45%.

• 전자공학회논문지CI
• /
• 제43권4호
• /
• pp.39-49
• /
• 2006

본 논문에서는 차세대 입출력 인터페이스인, PCI 익스프레스 컨트롤러의 기능 검증을 위해 효율적인 검증 환경을 제안하였다. 검증 환경은 벡터 생성 부분, 테스트 벤치, 그리고 두개의 메모리로 구성된다. 이러한 효율적인 검증 환경을 제대로 동작시키기 위한 명령어 세트를 정의하였다. 이 명령어는 어셈블리 구조를 가지며, PCI 익스프레스의 모든 프로토콜을 지원하며, 설계된 PCI 익스프레스 컨트롤러를 검증하기 위한 모든 시나리오를 제공하도록 정의되었다. 또한 본 논문에서는 랜덤 벡터 생성 부분, 시뮬레이션 부분, 그리고 비교 엔진으로 구성된 랜덤 검증 환경을 제안하였다. 본 랜덤 테스트 검증 환경에서 수행된 결과는 일반적인 기본 동작 검증과 설계 기반 검증에서 찾지 못한 특수 경우의 에러도 발견 할 수 있다.

• 한국추진공학회지
• /
• 제4권3호
• /
• pp.19-28
• /
• 2000

고체추진 로켓모타의 개발이나 성능평가 때에는 추진기관의 추력, 연소실 압력, 온도, 연소시간 등 정적연소시험을 통해서 필요한 데이터론 측정한다. 그러나 휴대용 대공 유도무기의 경우에는 추진기 관의 화염으로부터 사수를 보호하기 위해 대단히 까다로운 안전규정을 요구하고 있다. 이러한 안전 규정들을 만족시키기 위해 설계된 분리장치나 점화안전장치의 개발 및 성능평가를 위해서는 이들 장치들이 결합된 추진기관에 대해 실제 비행 환경 하에서 설계목표의 신뢰도를 시험하기 위한 동적연소시험이 수행되어야 한다. 본 연구에서는 이러한 휴대용 대공 유도무기 추진시스템의 개발이나 성능평가를 위한 동적연소시험 기법 및 동적시험대의 설계 및 제작에 관한 연구를 수행하였다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2004년도 춘계학술발표회논문집
• /
• pp.3-8
• /
• 2004

This study describes the validation of the GPS/Levelling using GPS data that were obtained from three Permanent GPS stations of the Jeju island. Each orthometric height of three Permanent GPS stations was calculated from the Bench mark of levelling with Traverse-survey and relative baseline processing The test result shows that the error of closure of orthometric height was about 1.6cm and one of ellipsoidal height was about 1.5cm. This result represents that the geoidal height and undulations are regular in the Jeju island. According to the test results, it is identified that one can calculate the orthometric height using Permanent GPS station data rather than traditional levelling method which has a some complexity especially in Jeju island.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2007년도 춘계학술발표회 논문집
• /
• pp.89-92
• /
• 2007

This investigation aims at calculating the geoid height, distance between the ellipsoidal height and the orthometric height by GPS/Levelling data for nationwide 58 Bench Marks, and calculating the effect of geoid height to engineering public works. The accuracy of the results from baseline analyses and adjustment of a network. using GPS surveying data by nationwide 58 BM show 4mm for horizontal direction and 7cm for vertical direction. The 58 geoid height was calculated by GPS/Levelling. For a construction work field GPS/Levelling for distributed 4 BM in test area can calculate the orthometric height in 20 ppm relativity accuracy with 95% reliability. Besides the calculated geoid height in the investigation was 0.367m higher than EGM96 model. The test results of a engineering work site, the result by EGM96 model was 1.8cm in 10km and it was also 3.6cm in interpolation method. The results show that it is equivalent to levelling of $20mm\sqrt{S}$.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.429-430
• /
• 2002

In this study, three kinds of brake: discs including two coated brake discs and one steel disc were tested under the same experimental conditions on a reduced scale braking test bench. Plasma spray coating technique was used to coat ceramic powder on the discs. In the test, four commercial sintered brake pads were coupled with discs. Ceramic coated discs have shown good stability in friction coefficient at high speed and high energy braking conditions. However, ceramic coated discs caused more wear loss of pad mass than the steel disc. It was shown that thermal barrier effect in ceramic coated discs adjusted the thermal partition between pad and disc. Steel disc showed fluctuating friction coefficient at high speed but less wear loss of pad mass than ceramic coated discs.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.163-164
• /
• 2011

본 논문은 스마트그리드용 배터리 에너지 저장장치(Battery Energy Storage System, BESS)와 같은 대용량 전력변환장치의 개발 및 성능검증 시험에 사용된 대용량 시험설비에 대해 기술하였다. 대용량 시험설비는 모의 수 배전 계통 설비, DC Power Supply, 부하설비로 구성되어 있다. 모의 수 배전 설비는 개발 시험규격과 계통 상황을 모의하고, DC Power Supply는 연료전지나 배터리 등의 DC Source, 수동부하장치는 전력 변환 설비의 각종 부하들을 모의하기 위해 설계 제작하여 스마트그리드용 2MVA BESS의 성능검증 시험에 이용하고 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.425-431
• /
• 2002

In this study the characteristics of E-EGR valve developed by electrical method were analysed and the feasibility of application to vehicles was evaluated. The engine of smart car applied for diesel passenger car of small-displacement size developed by common vehicle was used for this experiment. It was installed a 3-cylinder, $0.8\ell$, turbo-charged light duty diesel engine with an electronic EGR valve. After the analysis and comparison of E-EGR valve performance by test bench, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권5호
• /
• pp.47-54
• /
• 1991

The lip seals widely used nowadays in stern tube sealing system of ships have radial sealing contact with shafts or liners, on the other hand the face seals of stern tube sealing system have axial sealing contact with seat. Because of axial sealing contact, the face seals have a large number of merits such as durability of life, simplicity of structure, easy fitting and replacement, etc. In this paper, for the purpose of development of face seals, the fundamental properties of axial sealing contact were analyzed and a trial face seal was designed and manufactured using N.B.R. rubber and Thordon which is widely used for bearing materials. The seal proper of trial face seal was made from N.B.R. rubber and the face insert was made from Thordon, thermosetting resins which are three dimensional, cross linked condensation polylmers. The performance test of trial face seal was carried out on the test bench which was specially designed and manufactured. The results were satisfactory enough to be used in practical stern tube sealing system.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.60-66
• /
• 2004

Increased energy costs have placed demands for improved combustion efficiency, high equipment availability, low maintenance and safe operation. Simultaneously low NOx modification, installed due to stricter environmental legislations, require very careful combustion management. The flame diagnostics system has been developed specially to meet these requirements. We aimed at gaining the relationship between burner flame image and emissions such as NOx and unburned carbon in furnace by utilizing the image processing method. For the first step of development, its possibility test was undertaken with bench furnace. The test proceeded to the second step with pilot furnace, the system was observed to be effective for evaluating the combustion conditions.