• Tunnel and Underground Space
• /
• v.22 no.1
• /
• pp.1-11
• /
• 2012

Thermal energy storage is defined as the temporary storage of thermal energy at high or low temperatures for later use in need. The energy storage can reduce the time or rate mismatch between energy supply and demand, and thus it plays an important role in conserving energy and improving the efficiency of energy utilization, especially for renewable energy sources which provide energy intermittently. Underground thermal energy storage (UTES) can have additional advantages in energy efficiency thanks to low thermal conductivity and high heat capacity of surrounding rock mass. In this paper, we introduced the technologies of underground thermal energy storage and rock caverns for hot water storage in Sweden.

• Journal of the Society of Disaster Information
• /
• v.15 no.2
• /
• pp.301-311
• /
• 2019

Purpose and Method: In this study, a questionnaire interview survey was conducted for the victims living in the temporary house by the Pohang earthquake, and improvements were derived. Results: As a result, major improvements in terms of facilities are as follows. First, in order to expand the toilet and cooking space, the existing inner gate and the wall are removed and the width of the toilet is expanded. Minimize the inconvenience by adding a cooking table as wide as the extended toilet. Second, a separate sleep compartment is set up to secure storage space in a limited area. And the storage closet is installed below and used as a storage space. At this time, the size of the sleeping space is set to double bed size. Third, curtains and blinds are installed on both windows to secure privacy, thereby protecting privacy and psychological stability. Conclusion: If the remodeling of the temporary house proposed in this study is utilized and applied, it is possible to provide a better living environment. In addition, it is expected that it will be possible to improve the efficiency of space and overcome existing spatial limitations by minimizing inconveniences reflecting the needs of the victims.

• Korean Management Science Review
• /
• v.30 no.3
• /
• pp.99-111
• /
• 2013

This paper studies the scheduling problem of storing and retrieving assembly blocks in a temporary storage yard. The objective is to minimize the number of relocations of blocks while the constraints for storage and retrieval time windows are satisfied. We present an integer programming model based on multi-commodity network flows, and the three revised models based on the properties of the problem. We show that the revised models are more efficient than the generic model through the numerical experiments.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3898-3906
• /
• 2023

The paper notes that the most common way of handling spent nuclear fuel (SNF) of power reactors is its temporary long-term dry storage. At the same time, the operation of the dry spent fuel storage facilities almost never use the modern capabilities of information systems in safety control and collecting information for the next studies under implementation of aging management programs. The author proposes a structure of an information system that can be implemented in a dry spent fuel storage facility with ventilated storage containers. To control the thermal component of spent fuel storage safety, a database structure has been developed, which contains 5 tables. An algorithm for monitoring the thermal state of spent fuel was created for the proposed information system, which is based on the comparison of measured and forecast values of the safety criterion, in which the level of heating the ventilation air temperature was chosen. Predictive values of the safety criterion are obtained on the basis of previously published studies. The proposed algorithm is an implementation of the information function of the system. The proposed information system can be used for effective thermal monitoring and collecting information for the next studies under the implementation of aging management programs for spent fuel storage equipment, permanent control of spent fuel storage safety, staff training, etc.

• Journal of Biosystems Engineering
• /
• v.19 no.2
• /
• pp.91-98
• /
• 1994

Planting, transplanting, and harvesting are important processes for the successful production of farm products in Korea because those require the high labor intensity during limitted period. Recently, many researches of using automatic control with a microcomputer are carried in the agricultural field, but are not much spread to the seeder development. Automatic sowing technology would be much attractive if there was a way to assure that each seed was count accurately in the seed metering device. Thus, an automatic seed metering device was designed and constructed to be controlled by microcomputer. This device could be improved in not only counting the number of seeds in but also sowing seeds between row spacings. Automatic seed metering device consisted of conveyor belt and temporary storage device. Performance of seed metering device depends on the apparatus including sensor, stepping motor and DC-solenoid. Research contents and results are summarized as follows. 1. The seed metering device involving seed hopper, sorter and temporary storage device was designed and constructed. 2. A seed counting system with six photo electric sensors, designed and built for this project, was adequate for tranferring and counting seeds accurately. 3. Operating algorithm for stepping motor and photo electric DC-solenoid was developed. The Seed metering device proved to be a smooth and accurate operating device using the algorithm. 4. The performance of second prototype metering device was examined with five kinds of seeds ; mung beans, red beans, white beans, black beans and corn to transfer and count the seeds. The error ratio of seed metering was less than 3.5%.

• Journal of Conservation Science
• /
• v.35 no.1
• /
• pp.51-60
• /
• 2019

This paper provides quantitative data that describes the evolution of the air quality in the Whale and Sea Museum, located in the Iwate prefecture, collected after the 2011 Great East Japan Earthquake and tsunami. The museum was damaged significantly by the disaster, and restoration works continued for over six years. The air quality in the temporary storage facility and museum was monitored during the rehabilitation process. Evaluation of air quality is carried out by gas chromatography- mass spectrometry, ion chromatography and high-performance liquid chromatography. The results showed that the characteristics of the chemical components differed depending on the measurement locations inside the building. The museum atmosphere tended to be alkaline as the airtightness increased because of the maintenance works at the entrance. It was also determined that it was necessary to study the intake/exhaust routes and to clean them according to the contamination degree. In Japan, there are recommended museum air quality standards for acetic acid, formic acid, alkali, and aldehydes. The results indicated that these standards should not be used as a reference for damaged museums. Furthermore, at the temporary storage facilities for to store the collections during the rehabilitation of the museum, solvents such as ethyl benzene, toluene, and xylene are initially abundant, although they can be reduced by ventilation, while other components such as 2E1H was confirmed in this case are likely to remain.

• IE interfaces
• /
• v.9 no.2
• /
• pp.203-218
• /
• 1996

This paper deals with a Direct-Input-Output Manufacturing System (DIOMS) which has a number of machine centers placed along a built-in automated storage/retrieval system (AS/RS). During its operations, the storage/retrieval(S/R) machine picks up a pallet from the pickup/deposit port of a machine center and then moves it either to an empty rack opening of the AS/RS for temporary storage or to place it on the port of another machine center for subsequent operation. The machine layout problem in DIOMS is formulated as an integer mathematical programming whose objective is to minimize the total expected distance of the loaded S/R machine during a production period. Recognizing the limit of the exact solution procedure(the Branch and Bound method), two improvement-type heuristics are proposed. One is based on the simulated annealing method and the other the pairwise interchange method. The validity of the heuristics is examined with example problems.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.321-322
• /
• 2006

Faults on power systems are inevitable phenomena. These faults can be classified by two categories, temporary and permanent faults. Without distinction of fault types, the faults would induce several changes on power system such as transmission line trip. Especially, the most common phenomena which loads experience by the power system fault is voltage sag. Voltage sags mean that the bus voltage maintains under 0.9 p.u. of rating for several cycles, and they give serious effects to operation of load devices. To ensure proper operation of the load, the flywheel systems, one of the energy storage system, are suggested in this paper. This paper demonstrates the efficiency of flywheel energy storage system against voltage sag by PSCAD/EMTDC simulation.

• Journal of the Korea Safety Management & Science
• /
• v.8 no.3
• /
• pp.103-114
• /
• 2006

A cross docking operation involves multiple trucks (known as inbound trucks) that deliver items from suppliers to a distribution center and multiple trucks (known as outbound trucks) that ship items from the distribution center to customers. Based on customer demands, an inbound truck may have its items transferred to multiple outbound trucks. Similarly, an outbound truck can receive its consignments from multiple inbound trucks. A unique characteristic of a cross docking system is the absence or prohibition of long term storage of items at the distribution center. Items delivered to the distribution center from suppliers are shipped to customers as soon as possible without being placed in storage in the distribution center. The objective of this paper is to develop the optimal operational strategy for finding the best truck docking sequence for both inbound and outbound trucks in order to minimize total operation time where a temporary storage area is not available in a cross docking system.

• Current Research on Agriculture and Life Sciences
• /
• v.14
• /
• pp.37-47
• /
• 1996

The main objectives of this studies are to present the most desirable rice processing complex model system in a given our situations by comparision and analyzing the major factors and, also recommend the future prospect of the rice processing complex in Korea. There are 3 different rice processing complex models in Korea. Those are concrete bin, flat type steel bin and square bin. These systems have a lot of differences and have their own characteristics such as capital requirement, efficiency, storage capacity and quality controls. The major problems of the existing rice processing centers in Korea are high fixed cost and the unbalnced systems. Following is summary to solve this problems: 1. Development of the large scale harvester and high speed continuous dryer. 2. Quality inspective system of bulk grain and large scale temporary storage facilities. 3. Large size readjustment of arable land. 4. Select the convenient location of rice processing center and formulation of well equipment facilities.