• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.155-159
• /
• 2003

Polycrystalline $Ti_{1-x}Co_xO_2$ thin films on $SiO_2$ (200 nm)/Si (100) substrates were prepared using liquid-delivery metalorganic chemical vapor deposition. Microstructures and ferromagnetic properties were investigated as a function of doped Co concentration. Ferromagnetic behaviors of polycrystalline films were observed at room temperature, and the magnetic and structural properties strongly depended on the Co distribution, which varied widely with doped Co concentration. The annealed $Ti_{1-x}Co_xO_2$ thin films with $x{\leq}0.05$ showed a homogeneous structure without any clusters, and pure ferromagnetic properties of thin films are only attributed to the $Ti_{1-x}Co_xO_2$ (TCO) phases. On the other hand, in case of thin films above x=0.05, Co clusters formed in a homogeneous $Ti_{1-x}Co_xO_2$ Phase, and the overall ferromagnetic (FM) properties depended on both $FM_{TCO}$ and $FM_{Co}$. Co clusters with about 10nm-150nm size decreased the value of Mr (the remanent magnetization) and increased the saturation magnetic field.

• Journal of the Korean Ceramic Society
• /
• v.45 no.9
• /
• pp.567-571
• /
• 2008

The properties of a grown film by the chemical vapor deposition process depend on the deposition temperature because the deposition mechanism of the CVD film is controlled by the deposition temperature. The preferred orientation of the zrC film changed from (111) to (220) or (200) with an increase of the deposition temperature. The grain size of the ZrC film changes from $0.8{\mu}m$ to $2.5{\mu}m$ in the range of 1350 to $1500^{\circ}C$. The hardness of the deposited ZrC film depended on the preferred orientation and the grain size. The hardness of the ZrC film deposited at $1400^{\circ}C$ was 31 GPa.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.39-44
• /
• 2004

The effects of the STS 304 hollow cylinder property variations on the non-steady heat conduction are considered in this paper. In the non steady state, the specific heat and conductivity are depended on the temperature variations, and these properties affect to the governing equation on heat conduction. But the most of numerical analysis on heat conduction is assumed to constant properties which is conductivity and specific heat. Assuming that the properties are reacted sensitively, the numerical results can have the difference of between constant properties with non constant properties. The main parameters are specific heat and conductivity. The temperature distributions of the STS 304 hollow cylinder became in steady state after 4 minutes in case of the constant properties. As the conductivity is varied with temperature, the temperature distributions became in steady state after 15 minutes. Therefore, a numerical analysis of the non steady state heat transfer is so important in case of varying temperature.

• Journal of Korea Foundry Society
• /
• v.18 no.6
• /
• pp.563-569
• /
• 1998

A Study on microstructure and elevated temperature strength of 18Cr-2Mo ferritic stainless steel castings strengthened by alloying small amounts of titanium and carbon, has been conducted. The morphology of titanium carbides showed spherical in shape and their distribution depended on the amount of alloying elements. Maximum density ($7{\times}10^5/cm^2$) of titanium carbides has been formed in the alloy containing 2.0 wt.% titanium and 0.5 wt.% carbon as alloying elements and the size of carbide particles is in the range of 0.5 to $3.0\;{\mu}m$. High temperature tensile and fatigue strength of this alloy were the highest among the alloys tested in this research. The fracture mode of the alloys containing alloying elements less that 2.0 wt.% titanium and 0.5 wt.% carbon showed intercrystalline fracture at room temperature, while the alloys containing higher amounts of alloying elements showed transcrystalline fracture. All of the alloys showed creep or ductile rupture mode at elevated temperature.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1552-1557
• /
• 2004

This paper introduced about characteristics on the non-steady heat transfer of STS 304 hollow cylinder, In the non-steady state, the specific heat and conductivity are depended on the temperature variations, and these properties affect to the governing equation on heat conduction. But the most of numerical analysis on heat conduction is assumed to constant properties which is conductivity and specific heat. Assuming that conduction is assumed to constant properties which is conductivity and specific heat. Assuming that the properties are reacted sensitively, the numerical results can have the difference of between constant properties with non-constant properties. The main parameters are specific heat and conductivity. The temperature distributions of the STS 304 hollow cylinder became in steady state after 4 minutes in case of the constant properties. As the conductivity in varied with temperature, the temperature distributions became in steady state after 15 minutes. Therefore, a numerical analysis of the non steady state heat transfer will has to apply that conductivity varied with temperature.

• Korean Journal of Materials Research
• /
• v.19 no.12
• /
• pp.686-691
• /
• 2009

The effects of thermal properties on the crystallization behavior of $CaMgSi_2O_6$ glass-ceramics were investigated as a function of sintering temperature from 800$^{\circ}C$ to 900$^{\circ}C$. The crystallization behavior of the specimens depended on the sintering temperature, which could be evaluated from the differential thermal analysis, X-ray diffraction and Fourier transform infrared spectroscopy. With increasing sintering temperature, the thermal conductivity of the sintered specimens increased, while the coefficient of thermal expansion (CTE) of the sintered specimens decreased. These results could be attributed to the increase of crystallization, confirmed from the estimation by density measurements. Also, the thermal diffusivity and specific heat capacity of the sintered specimens were discussed with relation to the sintering temperature. Typically, a thermal conductivity of 3.084 $W/m^{\circ}C$, CTE of 8.049 $ppm/^{\circ}C$, thermal diffusivity of 1.389 $mm^2/s$ and specific heat capacity of 0.752 $J/g^{\circ}C$ were obtained for $CaMgSi_2O_6$ specimens sintered at 900$^{\circ}C$ for 5 h.

• Korean Journal of Agricultural Science
• /
• v.49 no.2
• /
• pp.331-339
• /
• 2022

Deforestation and conservation of coniferous forest have been recognized as critical issues in Korea due to climate change. The main purpose of this research was to monitor changes of secondary metabolite contents and growth of Korean fir (Abies koreana) according to the temperature change in Mt. Halla. The Korean fir located at three different regions, Yeongsil, Witseoreum, and Jindallaebat, was monitored in April, July, and October from 2016 to 2018 and secondary metabolites, specifically lutein, α-carotenoid, and β-carotenoid, were analysed with high performance liquid chromatography. The results showed that average concentrations of lutein, α-carotenoid, and β-carotenoid were 0.82 - 23.30, 0.02 - 2.01, and 0.11 - 2.84 ㎍·g-1 and the highest concentration of secondary metabolite was observed in October compared to April and July. The average length and width of Korean fir in the three regions were 11.84 - 20.70 and 1.78 - 2.41 mm from 2016 - 2018. A correlation analysis showed that the concentrations of all three secondary metabolites were negatively correlated with temperature and a significant difference was observed between temperature and lutein concentration in Korean fir. Overall, growth and production of secondary metabolites in Korean fir highly depended on the temperature, and global warming thus might have an adverse effect on the growth and physiological changes of Korean fir in Mt. Halla.

• Korean Journal of Food Science and Technology
• /
• v.15 no.4
• /
• pp.392-398
• /
• 1983

A pilot single-screw food extruder was constructed, and its mechanical properties and product characteristics were investigated by using corn grits. The screw rotational speed was varied and the changes in temperature profile of the barrel for the start-up period of operation were measured. The rate of heat generation for the start-up period was affected by the screw speed and feed rate. The screw speed resulted in a great influence on the estimated dough viscosity. The changes in the dough viscosity could indicate the on-set of termoplastic reaction in the barrel. The expansion ratio during the start-up period mainly depended on the barrel temperature and the degree of thermoplastic reaction in the barrel. The barrel temperatures for the gelatinization and burning of corn grits depended on the screw speed as well as the feed rate.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.352-356
• /
• 2011

Transparent conducting oxide films like ITO/Au/ITO and AZO/Au/AZO were fabricated with a sputter at a low-temperature of less then $70^{\circ}C$ and their crystallization and opto-electrical properties were studied. X-ray diffractiometry showed that single-ITO layer was amorphous, whereas, ITO of ITO/Au/ITO multi-layer was crystal. The ITO crystallization and its orientation depended on Au crystallization. Surface roughness of the ITO-multi-layers were in the range of 29-88% of that of ITO-single layer. ITO on amorphous gold layer had more rough surface than ITO on crystal gold. The gold layer between ITO improved electrical conductivity. Carrier density, mobility, resistivity and sheet resistance of ITO-single layer were $2.3{\times}10^{19}/cm^3$, $85{\times}cm^2$/Vs, $31{\times}10^{-4}{\Omega}cm$, and $310{\times}{\Omega}/cm^2$, respectively. Those of ITO/Au/ITO-multi-layers depended on Au-interlayer-thickness, which were in the range of $3.6{\times}10^{19}{\sim}4.2{\times}10^{21}/cm^3$, $43{\sim}85cm^2$/Vs, $0.17{\times}10^{-4}{\sim}25{\times}10^{-4}{\Omega}cm$, and $1.7{\sim}20{\times}{\Omega}/cm^2$, respectively. The sheet resistances of the single-layer ITO and the multi-layer ITO were 310 and $2.7{\sim}21{\Omega}/cm^2$, respectively. That of AZO/Au/AZO was $8.6{\Omega}/cm^2$, which was better than the single-layer ITO.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.165-169
• /
• 2004

Microwave dielectric properties and the behavior of low-temperature sintering of $Zn_{1-x}(Li_{1/2}La_{1/2})_xTiO_3$ ($0.01{\leq}x{\leq}0.05$) with 4 wt% $H_3BO_3$ were investigated as a function of $(Li_{1/2}La_{1/2})^{2+}$ content. The sintering temperature of the specimens can be reduced from $1150^{\circ}C$ to $875^{\circ}C$ with the addition of 4 wt% $H_3BO_3$ as a sintering agent. Dielectric constant (K) and Temperature Coefficient of resonant Frequency (TCF) with the substitution of ($(Li_{1/2}La_{1/2})^{2+}$ ion depended on dielectric mixing rule. Quality factor (Qf) depended on density and microstructure. Typically, K of 26.5, Qf of 19,030 GHz and TCF of 7.5 ppm$/^{\circ}C$ were obtained for the specimens with x=0.03 sintered at $875^{\circ}C$ for 3 h.