• Journal of the Korean Vacuum Society
• /
• v.19 no.4
• /
• pp.293-299
• /
• 2010

Vertically aligned ZnO nanorods on Si (111) substrate were prepared by hydrothermal method. The ZnO nanorods on spin-coated seed layer were synthesized at $140^{\circ}C$ for 6 hours in autoclave and were thermally annealed in argon atmosphere for 20 minutes at temperature of 300, 500, $700^{\circ}C$. The effects of the thermal annealing on the structural and optical properties of the grown on ZnO nanorods were investigated by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), photoluminescence (PL). All the ZnO nanorods show a strong ZnO (002) and weak (004) diffraction peak, indicating c-axis preferred orientation. The residual stress of the ZnO nanorods is changed from compressive to tensile by increasing annealing temperature. The hexagonal shaped ZnO nanorods are observed. The PL spectra of the ZnO nanorods show a sharp near-band-edge emission (NBE) at 3.2 eV, which is generated by the free-exciton recombination and a broad deep-level emission (DLE) at about 2.12~1.96 eV, which is caused by the defects in the ZnO nanorods. The intensity of the NBE peak is decreased and the DLE peak is red-shifted due to oxygen-related defects by thermal annealing.

• Korean Journal of Weed Science
• /
• v.14 no.2
• /
• pp.120-127
• /
• 1994

To establish an efficient herbicide screening method for purple nutsedge(Cyperus rotundus) control, its sprouting characteristics, tuber production and responses on several herbicides were investigated under greenhouse condition. The tubers stored at $4^{\circ}C$ after sterilization with the diluted prochloraz(Spotac) solution showed higher sprouting than the non-sterilized did. The harvested tubers were not dormant, and the sterilized tubers which stored at low temperature had a sprouting capability of about 80% after 6 months. If the fresh weight of purple nutsedge tubers was decreased to below 48%, they could not sprout. However, the tubers soaked in water and then stored at low temperature could sprout by 88% even 6 months later. Sprouting and initial growth of tuber were much better at $35^{\circ}C$-day/$25^{\circ}C$-night than at 30/$20^{\circ}C$ or 25/$15^{\circ}C$. The half-sected tubers, which were prepared by setting the intact tuber of above 1.2g latitudinally, were shown similar initial growth to the intact but those sected crucifically were not. These results suggest that the half-sected tuber itself can be used as a material on herbicide screening. About 1000 tubers could be harvested when 10 tubers planted in a pot($56{\times}35{\times}16cm$) filled with the artificial soil were cultivated in greenhouse of $35^{\circ}C$-day/$25^{\circ}C$-night for 3 months(April-July, 1993). Chlorimuron, Bentazon and Norflurazon were selected as the standards for the screening because of providing relatively effective control on purple nutsedge in both soil-surface and foliar spray treatment.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.6
• /
• pp.453-458
• /
• 2001

The Rural Development Administration (RDA) of Korea now operates a system called Rice Variety Selection Tests (RVST), which are now being implemented in eight Agricultural Research and Extension Services located in eight province RVST's objective is to provide accurate yield estimates and to select well-adapted varieties to each province. Systematic evaluation of entries included in RVST is a highly important task to select the best-adapted varieties to specific location and to observe the performance of entries across a wide range of test sites within a region. The rice yield data in RVST for ordinary transplanting in Kangwon province during 1997-2000 were analyzed. The experiments were carried out in three replications of a random complete block design with eleven entries across five locations. Additive Main effects and Multiplicative Interaction (AMMI) model was employed to examine the interaction between genotype and environment (G$\times$E) in the biplot form. It was found that genotype variability was as high as 66％, followed by G$\times$E interaction variability, 21％, and variability by environment, 13％. G$\times$E interaction was partitioned into two significant (P＜0.05) principal components. Pattern analysis was used for interpretation on G$\times$E interaction and adaptibility. Major determinants among the meteorological factors on G$\times$E matrix were canopy minimum temperature, minimum relative humidity, sunshine hours, precipitation and mean cloud amount. Odaebyeo, Obongbyeo and Jinbubyeo were relatively stable varieties in all the regions. Furthermore, the most adapted varieties in each region, in terms of productivity, were evaluated.

• Korean Journal of Environmental Biology
• /
• v.31 no.4
• /
• pp.429-439
• /
• 2013

This study was conducted to identify the relationship between environmental factors and algal bloom, and provide information for efficient management based on the results of monitoring the environmental parameters and algal diversity in the Jundai reservoir from March 2011 to October 2013. Little change in the weather conditions was observed during the study period except for a slight decrease in rainfall. Concentration of TN and TP in the reservoir exceeded water quality standards for agriculture and significant correlation between algal growth and environmental factors was observed. Phytoplankton in Jundai reservoir included 6 classes, 40 genus, 62 species, and the phytoplankton abundance was in the range of $1.3{\times}10^4{\sim}2.8{\times}10^6$ cells $mL^{-1}$. The annual average of phytoplankton abundance and Chl-a gradually decreased as TN and TP concentrations decreased. Overall Anabaena sp., Oscillatoria sp., and Microcystis sp. were the dominant species in Jundai reservoir. As the water temperature increased, the dominant species were Anabaena sp., Microcystis sp. and Oscillatoria sp., in that order. Anabaena sp. was dominant from spring to early summer with increase in water temperature and pollutant concentrations, and high correlation with environmental factors was observed. Microcystis sp. was dominant depending on changes in the nutrient levels. In the case of Oscillatoria sp., there was no significant correlation between phytoplankton biomess and Chl-a. However, efficient management of water environment and practical control of algal bloom in small scale reservoir polluted by livestock and farm irrigation should be achieved by identification of the relationship between algal growth and environmental factors.

• Journal of Chitin and Chitosan
• /
• v.23 no.4
• /
• pp.244-255
• /
• 2018

Natural extract in liquid phase was adjusted to 0, 0.25, 0.5, 1, 2, and 4% concentration to check microbial changes and to measure 4, 8, $12^{\circ}C$ for refrigeration temperature. In the case of grapefruit extract, the microbial safety was maintained at all the concentrations at $4^{\circ}C$ storage, but the antimicrobial activity was maintained at $12^{\circ}C$ storage and at $8^{\circ}C$ and 21 days storage. In the case of grape seed extract, only the 4% of the culture at $8^{\circ}C$ satisfied the requirement of safety of food distribution for the last 21 days, and the safety criterion was satisfied only at 4% concentration at $12^{\circ}C$ for 18 days. Complex Scutellaria baicalensis extract showed the total number of microbial cells treated by concentration. It was confirmed that microbial flow safety was maintained at low temperature ($4^{\circ}C$). However, at $8^{\circ}C$ and $12^{\circ}C$, Exceeded the distribution limit. When polylysine was applied to brown rice cake, it showed activity in all groups except $4^{\circ}C$, but these properties were not observed at $8^{\circ}C$ and $12^{\circ}C$. At a concentration of 0.5% or more of chitosan, the growth of the microorganism is suppressed by the 21st day very stably, and a similar tendency is observed at 8 and $12^{\circ}C$, so that it may be an antimicrobial material that inhibits microorganisms. At the first day, the distribution standards for general bacterial counts were exceeded.Ethyl-pyruvate showed that microorganism safety was maintained at $4^{\circ}C$ and 1% concentration, and food safety was stable even at 2 or 4%. Glycine showed very good and stable distribution stability at $4^{\circ}C$. However, at $8^{\circ}C$ and $12^{\circ}C$, the shelf life of 14 days could not be maintained as with the addition of other antimicrobial active substances.

• Clean Technology
• /
• v.27 no.4
• /
• pp.332-340
• /
• 2021

With the recent reinforcement of emission standards, it is necessary to make efforts to reduce NOx from air pollutant-emitting workplaces. The NOx reduction method mainly used in industrial facilities is selective catalytic reduction (SCR), and the most commercial SCR catalyst is the ceramic honeycomb catalyst. This study was carried out to reduce the NOx emitted from steel plants by applying De-NOx catalyst coated on metallic monolith. The De-NOx catalyst was synthesized through the optimized coating technique, and the coated catalyst was uniformly and strongly adhered onto the surface of the metallic monolith according to the air jet erosion and bending test. Due to the good thermal conductivity of metallic monolith, the De-NOx catalyst coated on metallic monolith showed good De-NOx efficiency at low temperatures (200 ~ 250 ℃). In addition, the optimal amount of catalyst coating on the metallic monolith surface was confirmed for the design of an economical catalyst. Based on these results, the De-NOx catalyst of commercial grade size was tested in a semi-pilot De-NOx performance facility under a simulated gas similar to the exhaust gas emitted from a steel plant. Even at a low temperature (200 ℃), it showed excellent performance satisfying the emission standard (less than 60 ppm). Therefore, the De-NOx catalyst coated metallic monolith has good physical and chemical properties and showed a good De-NOx efficiency even with the minimum amount of catalyst. Additionally, it was possible to compact and downsize the SCR reactor through the application of a high-density cell. Therefore, we suggest that the proposed De-NOx catalyst coated metallic monolith may be a good alternative De-NOx catalyst for industrial uses such as steel plants, thermal power plants, incineration plants ships, and construction machinery.

• Journal of Food Hygiene and Safety
• /
• v.38 no.4
• /
• pp.217-227
• /
• 2023

The consumption of ready-to-eat side dishes is rapidly growing in South Korea. These foods are particularly vulnerable to microbiological contamination as they are often cooked without any treatment, such as heating or stored at room temperature after cooking. Hence, in 2022, we analyzed the ready-to-eat side dishes sold in Gyeongsangnam-do, South Korea for microbiological contamination. We collected 100 samples from supermarkets in 7 cities, and then examined them for presence of food-borne pathogens and sanitary indicator bacteria. In the analysis of the food-borne pathogens, Bacillus cereus and Clostridium perfringens were isolated from 51 samples (51.0%) and 3 samples (3.0%), respectively. However, both quantitatively met the Korean Food Standards Codex. Genes of five different enterotoxins and one emetic toxin were analyzed from the 51 isolated B. cereus strains. We detected enterotoxin entFM (100.0%), nheA (94.1%), hblC (58.8%), cytK (56.9%), and bceT (41.2%) in 51 isolates, and emetic toxin gene, CER, in only one (2.0%) isolate. We did not detect C. perfringens toxin gene (cpe) that causes food poisoning in any one of the three C. perfringens isolates. In the case of sanitary indicator bacteria, Kimchi had the highest levels of total aerobic bacteria and coliforms, followed by Saengchae, Jeotgal, Jeolim, Namul, and Jorim, respectively. We counted total aerobic bacteria at two different storage temperatures (4℃ and 20℃) to determine the effect of storage temperature. When stored at 20℃, total aerobic bacteria count increased in most of the ready-to-eat side dishes, except for Jeotgal. This result conclusively shows the need for refrigerating the ready-to-eat side dishes after purchase. Further research is needed to assess the risk and safety of the ready-to-eat side dishes available in the market and determine appropriate safety management practices.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.895-905
• /
• 1994

The solid phase crystallization behavior of undoped amorphous $Si_{1-x}Ge_{x}$ (X=O to 0.53) alloyfilms was studied by X-ray diffractometry(XRD) and transmission electron microscopy(TEM). Thefilms were deposited on thermally oxidized 5" (100) Si wafer by MBE(Mo1ecular Beam Epitaxy) at 300'C and annealed in the temperature range of $500^{\circ}C$ ~ $625^{\circ}C$. From XRD results, it was found that the thermal budget for full crystallization of the film is significantly reduced as the Ge concentration in thefilm is increased. In addition, the results also shows that pure amorphous Si film crystallizes with astrong (111) texture while the $Si_{1-x}Ge_{x}$ alloy film crystallzes with a (311) texture suggesting that the solidphase crystallization mechanism is changed by the incorporation of Ge. TEM analysis of the crystallized filmshow that the grain morphology of the pure Si is an elliptical and/or a dendrite shape with high density ofcrystalline defects in the grains while that of the $Si_{0.47}Ge_{0.53}$ alloy is more or less equiaxed shape with muchlower density of defects. From these results, we conclude that the crystallization mechanism changes fromtwin-assisted growth mode to random growth mode as the Ge cocentration is increased.ocentration is increased.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.2
• /
• pp.26-29
• /
• 2011

Purpose: The general test method of the Korean Pharmacopeia specifies the test method on the clauses of quality control after manufacturing. According to KFDA Guidance for Medicines, standards of residual solvents regulates the maximum permissible dose of acetonitrile as 400 ppm, ethanol as 5,000 ppm, and acetic acid as 5,000 ppm. This study aims at identifying the type of resiual solvents in the final [F-18]FDG vial of an automatic synthesizer and measure its residual quantity. Materials and Methods: The center carried out residual solvents test of [F-18]FDG injection using Agilent Technologies 7890A with a Flame Ionization Detector. The column of Agilent Technologies 7890A used in measuring of residual solvents was CP WAX column ($30m{\times}0.53mm{\times}1.0{\mu}m$) and analysis condition was split mode 1:1 at the initial temperature $70^{\circ}C$ which was increased $20^{\circ}C/minute$ after two minutes and maintained at the final $140^{\circ}C$ for two minutes. The analysis method was as following: Firstly, ethanol-acetonitrile-acetic acid mixture was classified into four types of concentration (250-25-250 ppm, 1,000-100-1,000 ppm, 3,000-300-3,000 ppm, and 6,000-600-6,000 ppm), and $1.0{\mu}L$ of each type of concentration was injected into gas chromatography followed by an analysis of its peak domain. Then, a calibration-curve by the external standard method was drawn based on the analysis result. Results: While ethanol and acetonitrile were detected in TRACERlab MX, FASTlab had additional acetic acid. The residual quantity of the ethanol-acetonitrile-acetic acid mixture evaluated using the calibration-curve was average 72 ppm ethanol, 54 ppm acetonitrile, and 1030 ppm acetic acid for FASTlab, whereas average 439 ppm ethanol and 79 ppm acetonitrile for TRACERlab MX. This indicated that both of them were within the maximum permissible dose. Conclusion: Solvent residues in the [F-18]FDG injection were all within maximum permissible doses and proper to be used to examine a patient. The result indicated that types and quantities of solvent resides of radioactive pharmaceuticals vary depending on the automatic synthesizer.

• Journal of the East Asian Society of Dietary Life
• /
• v.13 no.1
• /
• pp.25-38
• /
• 2003

This study was conducted to establish the microbiological quality standards applying the HACCP system on sushi items of Japanese restaurant in Korea. The study evaluated hygienic conditions of kitchen and workers, pH time-temperature relationship, and microbial assessments during whole process of sushi making in 2001. Overall hygienic conditions were normal for both kitchen and for workers by 3 point scale, but hygienic controls against the cross-contamination were still needed. Each process of sushi making was performed under the risk of microbial contamination, since pH value of most of ingredients was over pH 4.6 and also production time(3.5~6 hrs) were long enough to cause problems. Microorganisms were high enough to cause foodborne illness ranged 8.0$\times$10$^2$~3.3$\times$10$^{6}$ CFU/g of TPC and 1.0$\times$10$^1$~1.6$\times$10$^3$CFU/g of coliforms, although TPC, coliforms and Staphylcoccus aureus were within the standard limits (TPC 10$^2$~10$^{6}$ CFU/g, coliforms 10$^3$CFU/g). However, Salmonella and Vibrio parahaemolyticus were not detected. High populations TPC and coliforms were also found in the cooks' hands and cooking utensils(TPC 10$^2$~10$^{6}$ CFU/100cm$^2$and Coliforms 10$^1$~10$^3$CFU/100cm$^2$). Based on the CCP decision tree analysis, the CCPs were the holding steps far six sushi production line except the tuna and the thawing step for tuna sushi. In conclusion, overall state of sushi production was fairly good but much improvement was still needed.