• Geomechanics and Engineering
• /
• 제10권2호
• /
• pp.125-135
• /
• 2016

Adhesion in geotechnical engineering is the interaction between cohesive soil and a solid surface which can cause clogging in mechanized tunnelling through clayey formations. Normal piston pull out and modified direct shear tests were performed on clayey soil samples to determine which type of adhesion stress, normal or tangential, could be most effectively measured. Measured values for normal adhesion ranged from 0.9 to 18 kPa. The range of tangential adhesion was 2.4 to 10 kPa. The results indicate normal adhesion results were more accurate than those for the modified direct shear test that measure tangential adhesion. Direct shear test on identical samples did not show any correlation between measured cohesion and normal adhesion values. Normal adhesion values have shown significantly meaningful variation with consistency index and so are compatible with the base of field clogging assessment criteria. But tangential adhesion and cohesion were not compatible with these assessment criteria.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.334-340
• /
• 2002

This paper proposes a new anti-slip re-adhesion control system fur electric railway vehicle driven by inverter-fed induction motors. This paper introduces an instantaneous tangential farce coefficient estimator between driving wheel and rail, which is based on disturbance observer. The torque command of proposed system regulates to exceed this estimated tangential farce coefficient in order to avoid undesirable slip phenomenon of driving wheels. We have already proposed the anti-slip re-adhesion control system based on disturbance observer for simplified one wheel equivalent model successfully. This paper extend to this system to the actual bogie system, which has four driving wheels driven by two induction motors fed by one inverter. In order to apply anti-slip re-adhesion control to the actual bogie system a new anti-slip re-adhesion control based on both disturbance observer and speed sensor-less vector control of induction motor with quick response are combined. The experimental results and the numerical simulation results prove the validity of the proposed control system.

• 정보저장시스템학회논문집
• /
• 제5권2호
• /
• pp.82-88
• /
• 2009

Understanding the adhesion behavior and characteristics of toner film is required to achieve image and text printing with high quality resolution. Toner can be considered as a thin film coating on a media such as paper or polymer film. Quantitative measurement of adhesion characteristics of the thin film is important to assess the reliability of the system. In this work the main objective was to investigate the adhesion characteristic between the toner and the media by ramp loading scratch test method. The scratch test may be used to obtain quantitative information about the adhesion of the film to the substrate. In the scratch test a diamond tip was used to scratch the surface of the toner film under an increasing normal load until the toner detached or fractured. The critical load (LC) was obtained from the experimental results. Also, the relationship between the critical load and the adhesive strength of the interface between the substrate and the toner was obtained by measuring the normal and tangential forces during the scratch test. Finally, theoretical analysis of the toner scratch characteristics was performed based on Benjamin and Weaver theory, Plowing model, and Laugier model.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.109-116
• /
• 2000

The objective of this study is to measure rim surface adhesion and to calculate motion resistance produced by the adhesion acting on the rim section of a circular wheel under sticky soil condition. The mechanisms of generating motion resistance by the adhesion on a circular wheel were analyzed through wheel motion. Experiments were conducted in an indoor soil bin that contains loam soil. A circular steel wheel was used for experiments. A part of the wheel rim was cut off, and transducers which can measure normal and tangential forces were installed in this section. Calculated motion resistance at a part of the rim section was superposed for one wheel rotation as motion resistance produced by the rim surface adhesion. The motion resistance increased with increasing the dynamic load. Ratio of the motion resistance to total motion resistance measured by an axis transducer was about 23 to 46 % in this study.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.1166-1175
• /
• 1993

The objective of this study is to measure contra-retractive adhesion and lift resistance acting on the rim section of a circular wheel for analyses of their effects on the dynamic load. A circular iron wheel was used for experiments. A part of the wheel rim was cut off, and transducers which can measure normal and tangential forces were installed in this section. Experiments were conducted on a laboratory soil bin which was filled with clayey soil under wet and dry conditions. The mechanism of generating contra -retractive adhesion on a circular wheel were analyzed by the experiments and motion analyses of the wheel. Effects of lift resistance on dynamic load were analyzed by measured forces under wet soil conditions in comparison in comparison with those under dry conditions. The showed that a part of the lift resistance were transferred to the dynamic load. These results may become basic data and ideas for analyses of tractor dynamic under wet soil conditions.

• Tribology and Lubricants
• /
• 제19권4호
• /
• pp.230-236
• /
• 2003

In applications such as MEMS and NEMS devices, the adhesion force and contact load may be of the same order of magnitude and the static friction coefficient can be very large. Such large coefficient may result in unacceptable and possibly catastrophic adhesion, stiction, friction and wear. To obtain the static friction coefficient of contacting real surfaces without the assumption of an empirical coefficient value, numerical simulations of the contact load, tangential force, and adhesion force are preformed. The surfaces in dry contact are statistically modeled by a collection of spherical asperities with Gaussian height distribution. The asperity micro-contact model utilized in calculation (the ZMC model), considers the transition from elastic deformation to fully plastic flow of the contacting asperity. The force approach of the modified DMT model using the Lennard-Jones attractive potential is applied to characterize the intermolecular forces. The effect of the surface topography on the static friction coefficient is investigated for cases rough, intermediate, smooth, and very smooth, respectively. Results of the static friction coefficient versus the external force are presented for a wide range of plasticity index and surface energy, respectively. Compared with those obtained by the GW and CEB models, the ZMC model is more complete in calculating the static friction coefficient of rough surfaces.

• 콘크리트학회논문집
• /
• 제17권6호
• /
• pp.1053-1064
• /
• 2005

The mechanical damage of concrete is normally attributed to the formation of microcracks and their propagation and coalescence into macroscopic cracks. This physical degradation is caused from progressive and hierarchical damage of the microstructure due to debonding and slip along bimaterial interfaces at the mesoscale. Their growth and coalescence leads to initiation of hairline discrete cracks at the mesoscale. Eventually, single or multiple major discrete cracks develop at the macroscale. In this paper, from this conceptual model of mechanical damage in concrete, the computational efforts were made in order to characterize physical cracks and how to quantify the damage of concrete materials within the laws of thermodynamics with the aid of interface element in traditional finite element methodology. One dimensional effective traction/jump constitutive interface law is introduced in order to accommodate the normal opening and tangential slips on the interfaces between different materials(adhesion) or similar materials(cohesion) in two and three dimensional problems. Mode I failure and mixed mode failure of various geometries and boundary conditions are discussed in the sense of crack propagation and their spent of fracture energy under monotonic displacement control.

• Structural Engineering and Mechanics
• /
• 제84권1호
• /
• pp.17-33
• /
• 2022

An experimental study is carried out to investigate the performance of the cutting tool regarding the insert wear, surface roughness, cutting forces, cutting power and material removal rate of three coated carbides GC2015 (TiCN-Al₂O₃-TiN), GC4215 (Al₂O₃-Ti(C,N)) and GC1015 (TiN) during the dry turning of AISI4140 steel. For this purpose, a Taguchi design (L₉) was adopted for the planning of the experiments, the effects of cutting parameters on the surface roughness (R_a), tangential cutting force (F_z), the cutting power (P_c) and the material removal rate (MRR) were studied using analysis of variance (ANOVA), the response surface methodology (RSM) was used for mathematical modeling, with which linear mathematical models were developed for forecasting of R_a, F_z, P_c and MRR as a function of cutting parameters (V_c, f, and a_p). Then, Multi-Objective Ant Lion Optimizer (MOALO) has been implemented for multi-objective optimization which allows manufacturers to enhance the production performances of the machined parts. Furthermore, in order to characterize and quantify the flank wear of the tested tools, some machining experiments were performed for 5 minutes of turning under a depth of 0.5 mm, a feed rate of 0.08 mm/rev, and a cutting speed of 350 m/min. The wear results led to a ratio (V_B-GC4215/V_B-GC2015) of 2.03 and (V_B-GC1015/V_B-GC2015) of 4.43, thus demonstrating the efficiency of the cutting insert GC2015. Moreover, SEM analysis shows the main wear mechanisms represented by abrasion, adhesion and chipping.

• Journal of the Korean Wood Science and Technology
• /
• 제2권2호
• /
• pp.25-31
• /
• 1974

포푸라와 일본잎갈나무는 속성조림 수종으로 적극 장려되고 있으나 구조용재로서 저재질인 까닭에 그 이용도가 제한되고 있다. 따라서 이들의 이용도 증진과 수요의 안정화를 위하여 대량으로 소비되는 일반 건축용재로 이용할 수 있는 형질의 개량과 강도 증진을 목적으로 임업시험장에서 1967년부터 포푸라와 일본잎갈나무의 집성재 제조조건을 구명하기 위하여 본 시험연구를 시작하여 현재까지 포푸라와 일본잎갈나무의 접착, scarf 접착성능과 실대형통직, 만곡 집성재의 제조조건 및 이 수종 구성집성재 제조에 의한 포푸라재의 집성강도 증진과 lamina 형질이 집성 강도에 마치는 영향을 구명한 결과 다음과 같은 결론을 얻었다. 1. 접착제 Resorcinol Plyophen #6000에 의한 미류(Populus deltoides)와 일본잎갈나무(Larix leptolepis)의 단일 수종, 이수종 접착성능, 방부처리, 미류의 접착성능과 미류와 일본잎갈나무의 scarf 접속 정착성능 및 방부처리, 마류의 scarf 접착성능을 구명한 결과 1.1 Block 전단 및 안장선단 시험에 의한 접착성능은 평균 목파율이 65%로 우수하였고, 미류는 촉단면이 경단면보다, 일본잎갈나무는 경단면이 촉단면 보다 접착성이 양호하였다(표 1, 2참조). 1. 2 방부제 Na-PCP는 resorcinol 수지 접착제의 접착력에 영향 하였으나 집성재 제조에 요구되는 접착력에는 영향하지 않았다(표 3, 4참조). 1. 3 Plane scarf joint 접착에 있어서 안전한 scarf비는 일본잎갈나무 1/12이상, 미류는 1/6이상이 요구되고 방부처리 미류의 plane scarf joint 접착의 안전 scarf 비도 무처리재와 같이 1/6 이상이 요구되었다(표 5, 6, 7 및 8참조). 2. 접착제 Resorcinol Plyophen #6000에 의한 미류와 일본잎갈나무의 단일 수종 및 이수종구성 집성재의 상대 접착력과 삶음반복 접착력 및 접착층의 박리시험에 의한 접착성능을 구명한 결과 2.1 실대형 통직, 만곡 집성재의 block 전단 상태 접착강도는 허용 최소상태 접착강도의 3배 이상이였으며 삶음반복 접착 강도는 상태접착 강도의 1/2로 감소 되었으나, 허용 최소 기준 삶음반복 접착강도의 2배 이상으로 실대형 내수 집성재 제조의 안전성이 확인되였다(표 9 및 10참조). 2.2 실대형 통직, 만곡집성재의 박리율은 미류, 이수종(일본잎갈나무+미류), 일본잎갈나무의 순으로 높았으나 최대치는 일본잎갈나무의 통직집성재(3.5%)로서 허용 최대 기준율보다 적었다.(표 11 참조) 3. urea 수지 접착제에 의한 이태리포푸라(Populus euramericana)와 일본잎갈나무의 단수종, 이수종 및 lamina 형질에 따른 5 ply 구성 통직 접성재의 휨강도 시험, 압축강도 시험에 의한 집성강도와 접착성능을 구명한 결과 3.1 집성강도가 요구되는 건축 구조용재를 목적으로 이태리포푸라와 일본잎갈나무의 이수종 구성 집성재를 제조할 때에는 수종 구성을 L(일본잎갈나무)+P(이태리포푸라)+L+P+L로 하는 것이 양호하였다.(표 12참조) 3.2 수심과 옹이를 가지는 lamina로 구성된 집성재의 경성 강도는 무결점 lamina로 구성된 집성재 강도보다 현저히 강도가 감소되므로 강도가 요구되는 구조용재로서의 집성재 제조에는 이들 결점 부재의 분산 집성이 필요하였다.(표 13참조) 3.3 실대형 통직 집성재의 FPL 전단 상태 접착강도는 허용 최소기준 상태 접착강도의 2배 이상으로 urea 수지접착제로서 이을 수종의 내장주조용 집성재 제조가 가능하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제46권3호
• /
• pp.213-220
• /
• 2018

리기다소나무를 구조용 집성재의 재료로 이용하기 위해 판면의 옹이와 대패가공 후 방치시간에 따른 수지 삼출량이 레조르시놀수지로 접착한 판재의 접착성능에 미치는 영향을 검토하였다. 고온($120{\sim}95^{\circ}C$) 및 저온($65{\sim}50^{\circ}C$)에서 건조한 리기다소나무의 수지 삼출량은 판목면이 정목면 보다 저온건조재가 고온건조재보다 많았다. 방치시간별로는 저온건조재는 3일째 고온건조재는 7일째에 최고함량을 보였고, 이후부터는 서서히 감소하여 15~90일에는 거의 차이가 없었다. 접착성능은 수지의 삼출이 많은 2~3일까지는 낮았으나 15일 이후에는 큰 차이가 없었으며, 고온 및 저온 건조재 모두 방치시간에 관계없이 KS 기준의 접착성능을 만족하였다. 옹이부가 포함된 적층 구성에서의 접착강도는 KS의 접착강도 기준 이상이었으나 목파율은 기준인 65% 이상을 만족하지 못하였다. 적층 단면구성(정목+정목, 판목+판목, 정목+판목)에 따른 접착성능은 고온 및 저온건조재 모두 모든 적층구성에서 KS의 기준을 크게 상회하였다.