• Journal of the Korean Institute of Landscape Architecture
• /
• v.48 no.3
• /
• pp.34-44
• /
• 2020

In order to suggest performance analysis directions of ecological components based on a vegetation-based LID system model, this study seeks to analyze the statistical significance between monitoring results by using SWMM computer simulation and rainfall and run-off simulation devices and provide basic data required for a preliminary system design. Also, the study aims to comprehensively review a vegetation-based LID system's soil, a vegetation model, and analysis plans, which were less addressed in previous studies, and suggest a performance quantification direction that could act as a substitute device-type LID system. After monitoring artificial rainfall for 40 minutes, the test group zone and the control group zone recorded maximum rainfall intensity of 142.91mm/hr. (n=3, sd=0.34) and 142.24mm/hr. (n=3, sd=0.90), respectively. Compared to a hyetograph, low rainfall intensity was re-produced in 10-minute and 50-minute sections, and high rainfall intensity was confirmed in 20-minute, 30-minute, and 40-minute sections. As for rainwater run-off delay effects, run-off intensity in the test group zone was reduced by 79.8% as it recorded 0.46mm/min at the 50-minute point when the run-off intensity was highest in the control group zone. In the case of computer simulation, run-off intensity in the test group zone was reduced by 99.1% as it recorded 0.05mm/min at the 50-minute point when the run-off intensity was highest. The maximum rainfall run-off intensity in the test group zone (Dv=30.35, NSE=0.36) recorded 0.77mm/min and 1.06mm/min in artificial rainfall monitoring and SWMM computer simulation, respectively, at the 70-minute point in both cases. Likewise, the control group zone (Dv=17.27, NSE=0.78) recorded 2.26mm/min and 2.38mm/min, respectively, at the 50-minutes point. Through statistical assessing the significance between the rainfall & run-off simulating systems and the SWMM computer simulations, this study was able to suggest a preliminary design direction for the rainwater run-off reduction performance of the LID system applied with single vegetation. Also, by comprehensively examining the LID system's soil and vegetation models, and analysis methods, this study was able to compile parameter quantification plans for vegetation and soil sectors that can be aligned with a preliminary design. However, physical variables were caused by the use of a single vegetation-based LID system, and follow-up studies are required on algorithms for calibrating the statistical significance between monitoring and computer simulation results.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.1
• /
• pp.72-85
• /
• 2018

This study focused on cases that led sustainable urban development through the construction and utilization of organic greenery systems linking green spaces of urban peripheries with metropolitan areas. To that end, Berlin - Brandenburg's regional parks in Germany and Milan's Raggi Verdi, a radial green axis project, in Italy were selected for analysis as case studies. As frameworks for this analysis, this study has established existing infrastructure accessibility and linkage, recycling and cooperative management. The results of the case study analysis are as follows: First, the specialized spatial strategy based on the individuality of the green space outside the city rather than a uniform landscape was used as the foundation of the sustainable development plan. Second, physical linkage from the center of the city to the periphery contributed to the sustainable development of the overall metropolis by improving the economic value of the surrounding area as well as ecological and environmental values. Third, the central management system was established to reduce the administrative inconvenience caused by multiple administrative districts in the green space of urban periphery. The implications of applying the above results to Seoul, Korea are as follows. First, it is necessary to establish a differentiation strategy by re-establishing the identity of a green landscape in the urban periphery, because the green spaces of Seoul's periphery are dispersed and mostly have a repetitious mountain landscape. Also, it is necessary to actively link peripheral mountains and urban green areas to create ecological value and economic value, and ultimately to help the sustainable development of the city. Finally, building an integrated management system is required to solve fragmented green space management departments in most of the urban periphery's green spaces. In conclusion, this study shows the significant possibility that the sustainable development of a metropolis can be derived from the utilization, linkage, and management of the green space in the urban peripheries, which is extraordinary compared to normal centralized urban development.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.1
• /
• pp.61-71
• /
• 2018

This study sought to interpret the Ya-Aeng (夜櫻) from the viewpoint of urban society, focusing on the occurrence of the Ya-Aeng at Changgyeongwon (昌慶苑) in the modern city of Kyungsung. When the Ya-Aeng started in the 1920s, the social aspects of Kyungsung were in a transitional period from the traditional to the modern. The social modernization of Kyungsung has had a dramatic impact on the Ya-Aeng as a part of the city culture. Using the concept of 'phantasmagoria', which was widespread in Kyungsung society and the Ya-Aeng, this study has established three implications of the Ya-Aeng. First, Kyungsung's phantasmagoria appeared in the form of crowds, spectacles, and experiences. This study suggests that such interpretation also applies to the Ya-Aeng. This means that the capitalism-controlled modern society on one hand and the Ya-Aeng on the other had the same mechanism. Therefore, the Ya-Aeng, as modern city culture, becomes a miniature version of Kyungsung and a modern commodity world in itself. Second, the fact that phantasmagoria is a major element of the landscape of the Ya-Aeng means that there is a special way of seeing. For modern subjects, the phantasmagoria of the Ya-Aeng has acted as a learning mechanism for a modern way of seeing. Third and finally, the phantasmagoria of the Ya-Aeng was an illusion to encourage the continued consumption of this culture and at the same time, forget about the capitalism-controlled urban culture. At this time, capitalism was dominated by the influence of Japanese imperialism. The significance of this study lies in that it expands the idea of the Ya-Aeng from the events inside Changgyeongwon into the urban culture, which is a projection of modern urban society. In addition, where the Ya-Aeng in the past had been regarded as a decadent and poor-quality spring celebration in comparison to the traditional spring celebration, this study proposes a new point of view for the Ya-Aeng in an urban social context.

• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.43-51
• /
• 2017

Purpose: The purpose of this study is to evaluate the dosimetric effects of couch attenuation and air gaps using 3D phantom for prone breast radiation therapy. Materials and method: A 3D printer(Builder Extreme 1000) and computed tomography (CT) images of a breast cancer patient were used to manufacture the customized breast phantom. Eclipse External Beam Planning 13.6 (Varian Medical Systems Palo Alto, CA, USA) was used to create the treatment plan with a dose of 200 cGy per fraction with 6 MV energy. The Optically Stimulated Luminescence Detector(OSLD) was used to measure the skin dose at four points (Med 1, Med 2, Lat 1, Lat 2) on the 3D phantom and ion-chamber (FC65-G) were used to perform the in-vivo dosimetry at the two points (Anterior, Posterior). The Skin dose and in-vivo dosimetry were measured with reference air gap (3 cm) and increased air gaps (1, 2, 3, 4, 5, 6 cm) from reference distance between the couch and 3D phantom. Results: As a result, measurement for the skin dose at lateral point showed a similar value within ${\pm}4%$ compared to the plan. While the air gap increased, skin dose at medial 1 was reduced. And it was also reduced over 7 % when the air gap was more than 3 cm compared to radiation therapy plan. At medial 2 it was reduced over 4 % as well. The changes of dose from variety of the air gap showed similar value within ${\pm}1%$ at posterior. As the air gap was increased, the dose at anterior was also increased and it was increased by 1 % from the air gap distance more than 3 cm. Conclusion: Dosimetrical measurement using 3D phantom is very useful to evaluate the dosimetric effects of couch attenuation and air gaps for prone breast radiation therapy. And it is possible to reduce the skin dose and increase the accuracy of the radiation dose delivery by appling the optimized air gap.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.284-284
• /
• 2016

Topological insulator (TI) is a bulk-insulating material with topologically protected Dirac surface states in the band gap. In particular, $Bi_2Se_3$ attracted great attention as a model three-dimensional TI due to its simple electronic structure of the surface states in a relatively large band gap (~0.3 eV). However, experimental efforts using $Bi_2Se_3$ have been difficult due to the abundance of structural defects, which frequently results in the bulk conduction being dominant over the surface conduction in transport due to the bulk doping effects of the defect sites. One promising approach in avoiding this problem is to reduce the structural defects by heteroepitaxially grow $Bi_2Se_3$ on a substrate with a compatible lattice structure, while also preventing surface degradation by encapsulating the pristine interface between $Bi_2Se_3$ and the substrate in a clean growth environment. A particularly promising choice of substrate for the heteroepitaxial growth is hexagonal boron nitride (h-BN), which has the same two-dimensional (2D) van der Waals (vdW) layered structure and hexagonal lattice symmetry as $Bi_2Se_3$. Moreover, since h-BN is a dielectric insulator with a large bandgap energy of 5.97 eV and chemically inert surfaces, it is well suited as a substrate for high mobility electronic transport studies of vdW material systems. Here we report the heteroepitaxial growth and characterization of high quality topological insulator $Bi_2Se_3$ thin films prepared on h-BN layers. Especially, we used molecular beam epitaxy to achieve high quality TI thin films with extremely low defect concentrations and an ideal interface between the films and substrates. To optimize the morphology and microstructural quality of the films, a two-step growth was performed on h-BN layers transferred on transmission electron microscopy (TEM) compatible substrates. The resulting $Bi_2Se_3$ thin films were highly crystalline with atomically smooth terraces over a large area, and the $Bi_2Se_3$ and h-BN exhibited a clear heteroepitaxial relationship with an atomically abrupt and clean interface, as examined by high-resolution TEM. Magnetotransport characterizations revealed that this interface supports a high quality topological surface state devoid of bulk contribution, as evidenced by Hall, Shubnikov-de Haas, and weak anti-localization measurements. We believe that the experimental scheme demonstrated in this talk can serve as a promising method for the preparation of high quality TI thin films as well as many other heterostructures based on 2D vdW layered materials.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.6
• /
• pp.327-340
• /
• 2017

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2016. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of flow, heat and mass transfer, the reduction of pollutant exhaust gas, cooling and heating, the renewable energy system and the flow around buildings. CFD schemes were used more for all research areas. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results of the long-term performance variation of the plate-type enthalpy exchange element made of paper, design optimization of an extruded-type cooling structure for reducing the weight of LED street lights, and hot plate welding of thermoplastic elastomer packing. In the area of pool boiling and condensing, the heat transfer characteristics of a finned-tube heat exchanger in a PCM (phase change material) thermal energy storage system, influence of flow boiling heat transfer on fouling phenomenon in nanofluids, and PCM at the simultaneous charging and discharging condition were studied. In the area of industrial heat exchangers, one-dimensional flow network model and porous-media model, and R245fa in a plate-shell heat exchanger were studied. (3) Various studies were published in the categories of refrigeration cycle, alternative refrigeration/energy system, system control. In the refrigeration cycle category, subjects include mobile cold storage heat exchanger, compressor reliability, indirect refrigeration system with $CO_2$ as secondary fluid, heat pump for fuel-cell vehicle, heat recovery from hybrid drier and heat exchangers with two-port and flat tubes. In the alternative refrigeration/energy system category, subjects include membrane module for dehumidification refrigeration, desiccant-assisted low-temperature drying, regenerative evaporative cooler and ejector-assisted multi-stage evaporation. In the system control category, subjects include multi-refrigeration system control, emergency cooling of data center and variable-speed compressor control. (4) In building mechanical system research fields, fifteenth studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, renewable energies, etc. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which could be help for improving the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the analyses of indoor thermal environments controlled by portable cooler, the effects of outdoor wind pressure in airflow at high-rise buildings, window air tightness related to the filling piece shapes, stack effect in core type's office building and the development of a movable drawer-type light shelf with adjustable depth of the reflector. The subjects of building energy were worked on the energy consumption analysis in office building, the prediction of exit air temperature of horizontal geothermal heat exchanger, LS-SVM based modeling of hot water supply load for district heating system, the energy saving effect of ERV system using night purge control method and the effect of strengthened insulation level to the building heating and cooling load.

• Journal of the Korean earth science society
• /
• v.37 no.4
• /
• pp.218-229
• /
• 2016

The bedform stability diagram indicates the shape and size of bedforms that will occur to a given grain size and flow velocity. The diagram has been constructed from experimental data which have been mostly acquired by flume experiments. Generally, the flume experiments have been performed on well sorted sediments with unimodal grain size distribution, in order to understand relationship between grain size and flow velocity. According to the diagram, a ripple structure initiates to be formed from lower flow regime flat bed, as the flow velocity increases on the surface of fine-sand or medium-sand sediments. This study aims to verify that the experimental result of bedform stability diagram will be reproduced in our flume experimental systems, and also to confirm that the result is consistent not only on well-sorted sand sediments but also on poorly-sorted sand sediments with bimodal grain size distribution. The experimental results in this study show that initiation of 2D or 3D ripple structure on poorly-sorted sand sediments requires higher flow velocity and shear stress than those for initiation of the structure on well-sorted sand sediments. In general, carbonate sediments are characterized by poor sorting due to inactive hydraulic sorting and bimodal grain size distribution with allochems and matrices. The results suggest that the carbonate depositional system possibly need a higher flow velocity for initial formation of 2D or 3D bedform structures. The reason might be the fact that pulling off and lifting of a grain in poorly sorted sediments require more energy due to sorting, friction, stabilization, armour effects, and their complex interaction. This preliminary study warrants additional experiments under various conditions and more accurate analysis on the relationship between formation of bedforms and grain size distribution.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.633-638
• /
• 2011

Mn substituted La, Sr or Ba-hexaaluminate were prepared by $(NH_4)_2CO_3$ co-precipitate method and calcined at $1,200^{\circ}C$ for 5 h. Catalysts were characterized by X-ray diffraction and $N_2$ physisorption and scanning electron microscope (SEM). Compared to $SrMnAl_{11}O_{19}$ and $BaMnAl_{11}O_{19}$, $LaMnAl_{11}O_{19}$ in which La located at mirror plane showed better crystallinity and high surface area, 13 $m^2/g$. $LaMnAl_{11}O_{19}$ revealed well developed plate-like structure which is characteristic structure of hexaaluminate. The catalytic activity of methane combustion increased in the following order: $LaMnAl_{11}O_{19}$ > $SrMnAl_{11}O_{19}$ > $BaMnAl_{11}O_{19}$ and was dependent on surface area of catalysts. 60 wt% $CeO_2/LaMnAl_{11}O_{19}$ calcined at $700^{\circ}C$ showed enhanced methane activity and methane was oxidized completely at low temperature ($700^{\circ}C$). It was confirmed that addition of ceria seems to be effective for the low and middle temperature combustion of methane. But, after calcination at high temperature of $1,200^{\circ}C$, it lost the promoting effect of ceria due to increase of ceria particle size and it had a limit to applying to the high temperature catalytic combustion.

• Korean Journal of Soil Science and Fertilizer
• /
• v.27 no.2
• /
• pp.98-104
• /
• 1994

Effects of paddy-upland rotation system on nutrients distribution in soil profile and nutrient balance were studied in paddy fields from 1989 to 1993. The obtained results are summarized as follows. 1. $NO_3{^-}-N$, Av.$P_2O_5$, Ex.-K, and EC were high by small extent in surface layer of 0~20cm soil depth without the sign of salt movement to deeper layers. On the contrary Ex.-ca, Ex.-Mg, and pH became high with increase of soil depths. 2. $NO_3{^-}-N$, Av.$P_2O_5$, Ex.-K, and EC in surface soil were high in the order of Converted, Paddy-Upland Rotation, Potato-Chinese Cabbage>2 Year, Rotation, Potato-Chinese Cabbage>Converted, Paddy-Upland Rotation, Soybean>Continous Paddy, which responded well to fertilizer application rates. On the other hand Ex.-Ca, Ex.-Mg, and pH in whole layers were high in the order of Converted, Paddy-Upland Rotation, Soybean>Converted, Paddy-Upland Rptation, Potato-Chinese Cabbage>2 Year, Rotation, Potato-Chinese Cabbage>Continuous Paddy, which largely depended on plant absorption. 3. Nutrient balance in upland cropping system cultivating potato and Chinese cabbage showed that the input of chemical fertilizer of nitrogen and potassium was less than the plant uptake, while it was reverse for phosphorus with much gap between fertilizer input and plant uptake. Therefore, phosporous was expected to be accumulated by 27kg/10a every year. 4. Nutrient balance in upland cropping system cultivating soybean showed that nitrogen was not deficient to soybean crops even the chemical fertilizer input was less than plant uptake because of nitrogen fixation by rhizobia. However, there was about 1kg/10a deficit of potassium, which resulted dificiency symptom in the middle stage of soybean growth. For phosphorous there was excess of 4kg/10a, which was expected to be short for maintaining phosphorous fertility of upland soils.

• Journal of Intelligence and Information Systems
• /
• v.23 no.1
• /
• pp.143-159
• /
• 2017

Due to the rapid development of IT in recent years, not only personal information but also the key technologies and information leakage that companies have are becoming important issues. For the enterprise, the core technology that the company possesses is a very important part for the survival of the enterprise and for the continuous competitive advantage. Recently, there have been many cases of technical infringement. Technology leaks not only cause tremendous financial losses such as falling stock prices for companies, but they also have a negative impact on corporate reputation and delays in corporate development. In the case of SMEs, where core technology is an important part of the enterprise, compared to large corporations, the preparation for technological leakage can be seen as an indispensable factor in the existence of the enterprise. As the necessity and importance of Information Security Management (ISM) is emerging, it is necessary to check and prepare for the threat of technology infringement early in the enterprise. Nevertheless, previous studies have shown that the majority of policy alternatives are represented by about 90%. As a research method, literature analysis accounted for 76% and empirical and statistical analysis accounted for a relatively low rate of 16%. For this reason, it is necessary to study the management model and prediction model to prevent leakage of technology to meet the characteristics of SMEs. In this study, before analyzing the empirical analysis, we divided the technical characteristics from the technology value perspective and the organizational factor from the technology control point based on many previous researches related to the factors affecting the technology leakage. A total of 12 related variables were selected for the two factors, and the analysis was performed with these variables. In this study, we use three - year data of "Small and Medium Enterprise Technical Statistics Survey" conducted by the Small and Medium Business Administration. Analysis data includes 30 industries based on KSIC-based 2-digit classification, and the number of companies affected by technology leakage is 415 over 3 years. Through this data, we conducted a randomized sampling in the same industry based on the KSIC in the same year, and compared with the companies (n = 415) and the unaffected firms (n = 415) 1:1 Corresponding samples were prepared and analyzed. In this research, we will conduct an empirical analysis to search for factors influencing technology leakage, and propose an early warning system through data mining. Specifically, in this study, based on the questionnaire survey of SMEs conducted by the Small and Medium Business Administration (SME), we classified the factors that affect the technology leakage of SMEs into two factors(Technology Characteristics, Organization Characteristics). And we propose a model that informs the possibility of technical infringement by using Support Vector Machine(SVM) which is one of the various techniques of data mining based on the proven factors through statistical analysis. Unlike previous studies, this study focused on the cases of various industries in many years, and it can be pointed out that the artificial intelligence model was developed through this study. In addition, since the factors are derived empirically according to the actual leakage of SME technology leakage, it will be possible to suggest to policy makers which companies should be managed from the viewpoint of technology protection. Finally, it is expected that the early warning model on the possibility of technology leakage proposed in this study will provide an opportunity to prevent technology Leakage from the viewpoint of enterprise and government in advance.